IO-Power Technology Co., Ltd
1F,No.212, Ln. 271, Wuling Rd., North Dist., Hsinchu City 30053, T iw n
http://www.io-power.com e-mail: io-power@io-power.com.tw Tel: 03-5429395 Cell: 0933168849 Fax: 03-5357297
Form No.
Form No.Form No.
Form No.
：
：：
：
IOP
IOPIOP
IOP-
--
-OANI
OANIOANI
OANI-
--
-001
001001
001-
--
-001 Rev.
001 Rev.001 Rev.
001 Rev.
：
：：
：
A.1
A.1 A.1
A.1
保存期限
保存期限保存期限
保存期限：
：：
：
6
66
6
年
年年
年
3.
3. 3.
3. AP Configuration with SMT User Interface
AP Configuration with SMT User InterfaceAP Configuration with SMT User Interface
AP Configuration with SMT User Interface
3
33
3-
--
-1.
1.1.
1.
Configuring AP
Configuring AP Configuring AP
Configuring AP with
with with
with Telnet
TelnetTelnet
Telnet
STEP
STEPSTEP
STEP–
––
–1
11
1.
..
.
Power on the AP
Power on the APPower on the AP
Power on the AP
1.Connect power supply to PoE injector with the AC power cord provided as shown in the above
diagram. The yellow POWER
POWERPOWER
POWER LED on the PoE will be on when the PoE has ade uate power supply.
2.Connect The AP to POWER & DATA OUT
POWER & DATA OUTPOWER & DATA OUT
POWER & DATA OUT port on the PoE with MIL-C-5015 IP67 Cat-5 Ethernet
Cable provided. The red ACTIVE
ACTIVEACTIVE
ACTIVE LED indicates if the AP has successfully powered-on.
3.Connect DATA IN
DATA INDATA IN
DATA IN port on the PoE injector with Ethernet cable to the LAN that the AP associates
with.
STEP
STEPSTEP
STEP–
––
–2
22
2. Verify IP address setting
. Verify IP address setting. Verify IP address setting
. Verify IP address setting
Configure the network settings on your PC to obtain an IP address. Computer uses IP addresses to
communicate with each other across a network, such as a LAN. The default IP address of the AP is
The default IP address of the AP is The default IP address of the AP is
The default IP address of the AP is
192.1 8.1.1
192.1 8.1.1192.1 8.1.1
192.1 8.1.1 so the PC needs to be set in the same net scope to access AP with Telnet.
1.Go to Con
ConCon
Control Panel
trol Paneltrol Panel
trol Panel
of your PC and
double-click Network
Network Network
Network C
CC
Connections
onnectionsonnections
onnections icon.
2.Right click Local
Local Local
Local Area
AreaArea
Area Connection
Connection Connection
Connection and select Properties
PropertiesProperties
Properties.
3.Select TCP/IP
TCP/IPTCP/IP
TCP/IP for the applicable Ethernet adapter and click Properties
PropertiesProperties
Properties.
4.Click the IP Address
IP AddressIP Address
IP Address tab page, select USE the following
USE the following USE the following
USE the following IP address
IP addressIP address
IP address, type an address between
192.1 8.1.
192.1 8.1.192.1 8.1.
192.1 8.1.2
22
2 to 192.1 8.1.254
92.1 8.1.25492.1 8.1.254
92.1 8.1.254 (192.168.1.1 is for the AP) for IP Address
IP AddressIP Address
IP Address and 255.255.255.0
255.255.255.0255.255.255.0
255.255.255.0 for Subnet
Subnet Subnet
Subnet
Mask
MaskMask
Mask, then click OK
OKOK
OK button.
STEP
STEPSTEP
STEP–
––
–3
33
3.
. .
. Connect the AP by telnet
Connect the AP by telnetConnect the AP by telnet
Connect the AP by telnet
After having the correct connection, start the telnet session to 192.1 8.1.1
192.1 8.1.1192.1 8.1.1
192.1 8.1.1. Enter the default password
Enter the default password Enter the default password
Enter the default password
(Please Check User Menu)
(Please Check User Menu)(Please Check User Menu)
(Please Check User Menu) and press ENTER on your keyboard to enter the main menu. The system
menu tree (SMT) will appear on your terminal software as shown below.
Please refer to the user manual for detailed description of each selection item.
