IOGear GWHDKITD User manual

Wireless TV Connection
with Dongle
Quick Start Guide
GWHDKITD
PART NO. Q1504-b
www.iogear.com

1
Package Contents
Product Introduction
1 x GWHDKITD Transmitter
1 x GWHDKITD Receiver
1 x 3 feet HDMI Cable
1 x HDMI Extender Cable
1 x USB Cable
This wireless HDMI video extender includes transmitter and receiver that
will allow an HDMI signal to be extended up to 75 feet. IR passback allows
you to control the source device from the receiver side using the video
source remote control.
1 x IR Blaster Cable
1 x IR Receiver Extender Cable
1 x Antenna
1 x DC5V/2A Wall Mount Switching Power Supply
1 x Quick Start Guide

System Requirements
Features 2
1. Compliant with HDMI 1.3 and HDCP 1.2.
2. Highest resolution up to 1080p full HD.
3. Strong anti-interference by operating at 5GHz frequency.
4. Support point to point wireless configuration.
5. Support IR pass back with 20-60KHz frequency.
6. Range up to 75 feet.
7. Plug and play, no software installation required.
1 HDMI source device (DVD, PS3, Set top box, PC, etc.)
1 HDMI display device (SDTV, HDTV, projector with HDMI port, etc.)

Overview 3
F. Power input
G. Power indicator
H. Wireless connection indicator
I. HDMI output connector
J. IR receiver extender
cable connector
K. Antenna connector
A. HDMI input
B. Wireless connection indicator
C. Power input
D. Power indicator
E. IR blaster cable connector
Receiver Back
Transmitter
A
B C D E
F
I
J
GH
K

4
Hardware Installation
Please read safety instructions carefully before installation and operation:
1. Please pay attention to all the warnings and hints for this device.
2. Do not expose this unit to rain, moisture or liquid.
3. Do not insert any foreign object into the device.
4. Opening the enclosure will void the warranty.
5. Place the device in a well ventilated area.
6. Use DC5V/2A only. Make sure the specification matched if using 3rd
party DC adapters.
Note:
1) Transmission distance will vary due to the environment.
2) Obstructions such as wall, brick or glass will shorten the signal cover
range or cause signal degradation.
3) Ideally works best using line-of-sight.

Hardware Installation 5
Transmitter
STEP 1 Insert the transmitter into an open HDMI port on the video source device
(Blu-ray, computer, media player, etc.). In case the space is too tight around the
HDMI port, or the position of the HDMI port is at an awkward angle and could
possibly cause a connection issue, use the HDMI cable extension cable included in
the package to increase the space or correct position issues.
STEP 2 Use the USB charging cable to connect the micro USB port on the
transmitter to a type A USB port on the source device to obtain power. In the rare
case that the source device has no USB port, please use a 5V USB power adapter
with a minimum 500mA output (not included in the package).
3
2
1
STEP 3 Skip this step if the video source device does not use an IR remote,
for example, a computer. Take the IR Out for TX cable from the box, connect the
IR TX cable to the IR Out port on the transmitter; peel off the protective paper from
the sensor end of the cable and place it in front of the video source device with the
round area of the IR TX sensor facing the IR sensor on the source device (it is very
important to accurately identify the IR sensor area on the video source device, you
may have to use your remote very close to the video source device to find it).

Hardware Installation 6
STEP 4 Install the antenna to the receiver
STEP 5 (Disregard this step if skipped in step 3) Take the IR In for RX cable
from the box, insert IR RX cable to the IR In port on the receiver; peel off the
protective paper from the sensor end of the cable and place it with the round
area of the IR sensor facing out towards the viewing area, the IR RX sensor
must be able to receive the signal from the video source device remote control.
STEP 6 Connect one side of the HDMI cable to the receiver and the other
side to your HDMI display device
Receiver
6
7
4
5

Hardware Installation 7
STEP 7 Connect DC5V/2A power supply to the Receiver power input port
STEP 8 Power on the video source device, then power on the video display. The
power indicator LED’s should be lit on both the transmitter and the receiver
indicating they are powered on. Once connected wirelessly, you should be able to
see the video content on the video display and both wireless signal LED’s should
blink which indicates video is being transmitted.
NOTE: This wireless kit is designed as a same-room solution, it is not intended to
go through walls.

8
FAQ
Q Everything is connected, power LEDs are on for both devices, but no
video on the video display.
A: 1. Make sure the video source device and the video display are turned on;
2. Check the HDMI cable connection at both sides to make sure they are
plugged in firmly;
3. Check the video input selection on the video display device, make sure that
the HDMI input port you selected is the same as the one you actually
plugged in;
4. If still no video after some time, connect the video source device to the
video display directly with the HDMI cable to make sure there are no
compatibility issues;
5. If the direct connection is working. reconnect everything restart (unplug
then re-plug the USB power cables) both transmitter and receiver and
make sure the LEDs light up.
Q Video is not stable on the video display.
A: 1. Check the distance and environment, make sure no other wireless devices
with a strong wireless signal is close;
2. Change the location of the transmitter and the receiver to make sure the
device is within the allowed range and there no obstacles in between;
3. Check the HDMI cable connection at both sides to make sure they are
plugged in firmly;
If all of the above has been checked and there is still no video displayed, contact
IOGEAR Technical Support for further support.

9
Specification
Items Specifi cation
Power supply
Voltage/Current Transmitter: DC5V/1A Receiver: DC5V/2A
Power consumption TX < 3W Rx < 5W
HDMI
performance
and interface
HDMI compliance HDMI 1.3
HDCP compliance HDCP 1.2
HDMI resolution supported
480i@60Hz, 480p@60Hz, 576i@50Hz,
576p@50Hz, 720p@50/60Hz, 1080i@50/60Hz,
1080p@50/60Hz
Supports audio formatsL/R stereo audio
Maximum transfer rate 10.2Gbps
Input and output TMDS signal 0.7 ~ 1.5Vp-p (TMDS)
Input and output DDC signal 5Vp-p (TTL)
Input cable length supported ≤ 5m (AWG26 HDMI 1.3 cable standard)
Output cable length supported ≤ 5m (AWG26 HDMI 1.3 cable standard)
Wireless
performance
and interface
Transmission method 5.8G Wireless transmission
Transmission distance 100 Feet (30.48 Meters)
Latency ≤ 200 ms
Protection level Electrostatic protection of the whole
machine
1a Contact discharge level 3
1b Air discharge level 3
Standard: IEC61000-4-2
Operating
environment
Working temperature0 ~ 40°C (32 ~ 122 °F)
Storage temperature -20 ~ 70°C (-4 ~ 158 °F)
Humidity (no condensation) 0 ~ 90%
Body properties
Dimension TX: 3.5 (W) x 1.54 (D) x 0.59 (H) in
RX: 5.18 (W) x 3.74 (D) x 0.78 (H) in
Material Plastic
Finishing Grit blast
Colour Black
Weight TX: 0.06lb, RX: 0.48lb
Reliability Mean time between failures (MTBF) >30000 Hours