IOGear GDP14W2 User manual

www.iogear.com
GDP14SW2
PART NO. Q1662
Quick Start Guide
2-Port 8K DisplayPort 1.4 Switch

Package Contents 1
System Requirements
Overview
1 x DisplayPort Switch
1 x USB-A to DC Power Cable
1 x Quick Start Guide
1x Warranty Card
The GDP14SW2 is a manual switch for connecting 2 sources to a
single monitor allowing to switch contents between the 2 sources.
Complies with DP 1.4 specification.
Supports:
8K @60Hz
8K @30Hz
4K @120Hz, 60Hz
1440 @165Hz, 144Hz, 120Hz, 60Hz.
1080P @165Hz, 144Hz, 120Hz, 60Hz.
Supported OS: Mac OS X, Windows.
Supports HDR.
Color sub-sampling: 4:4:4, 4:2:2, 4:2:0
• 2 x DispalyPort output source device (Bluray, Satellite box, PC etc.)
• 1 x DisplayPort input display device (HDTV, projector with
DisplayPort port, etc.)

2
Overview
A. Port selection switch
B. DP1 Input port
C. DP2 Input port
D.Power port
E. DP Output port
Top View
Back View
A
B
C
D
E
DP 1 In DP 2 In
SELECT
1 2
2-Port
8K
DisplayPort 1.4 Switch
DP-Out

Hardware Installation 3
1. Turn off all devices before connecting to the switch.
2. Connect DP output port of the source devices to DP1 and DP2
ports.
3. Connect the display DP input port to the switch DP output port.
4. Connect the supplied USB-A to a PC USB-A port or a power
adapter with USB-A port (not supplied) and the other end of the
cable to the switch.
5. Turn on your source and display devices.
6. Press the “Select” button to select the source you want to
display on your monitor/TV/projector.
DP 1 In DP 2 In
SELECT
1 2
2-Port
8K
DisplayPort 1.4 Switch
3
4
6
2
or
DP-Out

Warranty
Contact
Warranty Information
This product carries a 3 Year Limited Warranty. For the terms
and conditions of this warranty, please go to
https://www.iogear.com/support/warranty
Register online at https://www.iogear.com/register
Important Product Information
Product Model
Serial Number
WE’RE HERE TO HELP YOU!
NEED ASSISTANCE SETTING UP THIS PRODUCT?
Make sure you:
1. Visit www.iogear.com for more product information
2. Visit www.iogear.com/support for live help and
product support
IOGEAR
https://iogear.custhelp.com
[e-mail]
www.iogear.com

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits
for a Class B digital service, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. Any changes or
modifications made to this equipment may void the user’s authority
to operate this equipment. This equipment generates, uses, and can
radiate radio frequency energy. If not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help
FCC Caution: Any changes or modifications not expressly approved
by the party responsible for compliance could void the user’s
authority to operate this equipment.
Compliance Information