IOGear MiniView G-CS12 User manual



©1999 ATEN Technology, Inc. All Rights Reserved.
Microsoft and Windows 98 are registered trademarks of Microsoft
Corporation.
IBM is a registered trademark of International Business Machines,
Inc.
Macintosh, G3/G4 and iMac are registered trademarks of Apple
Computer, Inc.
ATEN is a registered trademark of ATEN Technology, Inc.
IOGEAR is a registered trademark of ATEN Technology, Inc.
ATEN Technology makes no warranty of any kind with regards to
the information presented in this document. All information
furnished here is for informational purposes only and is subject to
change without notice. ATEN Technology assumes no
responsibility for any inaccuracies or errors that may appear in
this document.

Packing List Packing List
The complete IOGEAR MiniViewTM package consists
of:
•One MiniViewTM KVM switch
•Two or four sets of custom cables, depending
on the model. G-CS12 comes with two cables
while G-CS14 comes with four.
•One User Manual
•One Quick-Start Setup Guide
Note: If your computers use AT keyboard
connectors, please contact us for a free set of
PS/2-AT adapters.
Please check to make sure that all components are
included and nothing is damaged. If you discover a
problem, please contact your dealer. Before
connecting your MiniViewTM, read the manual
thoroughly and follow the installation and operation
procedures carefully in order to prevent any
damage to the unit and/or any devices it connects
to.
Packing ListPacking List


Contents Contents
ContentsContents

Introduction ……...…………...……... 0101
Features ………………………………... 0202
Hardware Requirements …………… 0303
Installation …………………..………… 0404
Operation ………………………….……. 0606
Manual Port Selection
HotKey Port Selection …………….………. 0707
Auto Scan Mode ………………………….... 0808
Next/Last Mode ……………………….……. 0909
Appendix A ……………………………… 1010
Specifications
Appendix B ……………………………… 1111
Troubleshooting
Appendix C ………………………………. 1212
Contacting IOGEAR
Appendix D ………………………………. 1313
Radio Interference / Warranty

Introduction Introduction
Thank you for purchasing one of the smallest and most
feature-rich KVM switches on the market. IOGEAR’s
KVM switches are first-rate connectivity accessories
designed to help reduce the frustration of managing
multiple computer systems. With the MiniViewTMseries by
IOGEAR, you can access multiple computers from a
single console (keyboard, mouse and monitor). The
MiniViewTM provides two convenient methods to access
connected computers. Change ports easily via the push
button selection switch located on the unit’s side panel, or
by entering Hot Key combinations from the keyboard.
Setup is fast and easy; plugging cables into their
appropriate ports is all that is entailed. There is no
software to configure, no installation routines and no
incompatibility problems. Since the MiniViewTM intercepts
keyboard input directly, it works on any PS/2 compatible
hardware platform and with all operating systems. There
is no better way to save time and money than with a
MiniViewTM. By allowing a single console to manage the
attached computers, the MiniViewTM eliminates the
expense of purchasing a separate keyboard, monitor and
mouse for each PC. Additionally, these switches save all
the extra space multiple consoles would take up, and
eliminate the inconvenience and wasted effort involved in
constantly having to move from one PC to the other.
We hope you enjoy using your MiniViewTM KVM switch,
yet another first-rate connectivity solution from IOGEAR.
IntroductionIntroduction
11


Features Features
Supports Microsoft IntelliMouse, Logitech MouseMan+,
FirstMouse+, IBM Scroll Point Mouse and many others
Keyboard and mouse emulation for error free PC booting
Hot pluggable –add or remove connected PCs without powering
off the MiniViewTM
Full Plug-n-Play monitor support
Caps Lock, Num Lock and Scroll Lock status is saved and
restored when switching ports
Supports video resolutions up to 1920 x 1440
Easy installation -no software required
Built-in Auto Scan Mode
Uses standard connectors to connect PC’s
Easy to operate -PC selection via push button or Hot Keys
Compatible with all operating platforms
LED display for easy status monitoring
Saves time, space, power and equipment costs
Power-free design –the MiniViewTM draws power from the attached
computers
FeaturesFeatures
22


Hardware Hardware
Require Require
... ...
Console
One VGA, SVGA, or Multisync monitor capable of the highest
resolution that you
will be using on any PC in the installation
One PS/2 mouse
One PS/2 keyboard
or
One AT keyboard w/ a PS/2 keyboard adapter
PC
The following equipment must be installed on each PC that is to be
connected to
the system:
One VGA, SVGA or Multisync video card
One PS/2 mouse port
One PS/2 or AT keyboard port
* See the note under Cables in the next section.
Cables
Although it’s possible to use standard extender cables to connect
the PCs to the MiniViewTM, for optimum signal integrity and to
simplify the layout we strongly recommend that you use the high
quality custom cables that are provided as part of the package.
Note: The keyboard and mouse cables have PS/2 connectors at
each end. If your PC uses a standard AT style keyboard socket,
you will need an AT-PS/2 keyboard adapter in order to plug the
cable into the PC’s keyboard port. Be aware, however, that
because of the wiring and pin assignments, attempting to use
standard extender cables with adapters at both ends will not work.
You cannot use an AT-PS/2 adapter at the end that plugs into the
MiniViewTM.
The MiniViewTM supports PS/2 mice only. Please note that
PS/2-serial converters will not afford proper functionality with
your MiniViewTM KVM switch.
HardwareHardware RequirementsRequirements
33


Installation Installation
Before you begin, make sure that the computers you’re
going to connect to the MiniViewTM are turned off.
1Plug the monitor, keyboard, and mouse into the
console port connectors of the MiniViewTM unit.
2Use the extender cables (as described in the
Hardware Requirements and Unpacking sections) to
connect the monitor, keyboard and mouse ports of the
PCs to the MiniViewTM CPU ports, as shown in the
diagram to the right. If your PC uses an AT style
connector for the keyboard port, connect a PS/2-AT
adapter to the end of the cable that will connect to the
PC. If you don’t have a PS/2-AT adapter available,
please contact us and we’ll be happy to provide one at
no extra charge.
3Turn on the power to the connected PCs.
InstallationInstallation
44


Installation Installation
InstallationInstallation......
55


Operation Operation
Controlling the PCs in your MiniViewTM configuration
from a single console couldn’t be easier. Two port
selection methods provide instant access to any
attached PC:
Manual Port Selection
Hot Key Port Selection
Note: When powering-on, the MiniViewTM switches to port 1
by default. If the PC attached to port 1 is inactive, the
monitor will be blank so it may appear as if the unit is not
functioning. This is not the case. Simply use one of the port
selection
methods described below to switch to the active PC on a
different port.
Manual Port Selection
With manual port selection, you simply press the Port
Selection button on the
side panel of the MiniViewTM to switch between computers.
The selected LED on the top panel will light up to indicate
which port is active.
OperationOperation
66
