IOLINK XTB Series User manual

XTB Series7mm Pitch，Interface terminalUser's Guide● Applicable Crimp Terminal● Model Configuration● Product/SpecificationN .201210- M-ENG-XTB
■ HQ : (617-828) #28, Daedong-ro, Sasang-gu, BusanTEL : [phone] FAX : [phone]■ SEOUL Office: #1507, 96, Gamasan-ro, Geumcheon-gu, SeoulTEL : [phone] FAX : [phone]
Thank you for purchasing product of SAMW N ACT.
Please check model of product that you purchase first, and read this manual prior to use it.
● Caution for SafetyCaution Case that results in serious damage in human body or equipment, and fire if user handles
this equipment wrongly
Warning Case that results in slight damage in human body or equipment, and fire if user handles
this equipment wrongly
Warning
1. Use in permissible temperature range. (-10℃~+50℃)
It may cause damage to extermal case.
2. Use in permissible rated voltage (125V) or rated current range. (1A)
It may cause malfunction by misconnection.
3. Use AWG16(1.25㎟Max.) wire and applicable crimp terminals the terminal block.
4. Read the user manual carefully and check the specification, wiring, dimension, etc.
5. If you make the connection cable between the controller such as PLC and our product, carefully
check the internal wiring of terminal block and pin array of controller.
It may cause damage to controller or our product.
Major products
■ Relay terminal 1, 2, 4, 6, 8, 16, 32point
■ Interface terminal 20, 24, 26, 34, 40, 50, 40 x2pole
■ PLC I/O Connecting cables MITSUBISHI, LSIS, CIM N, MR N, FUJI, Y K GAWA, HITACHI, SIEMENS, AB, etc.
■ Servo Connecting cables Encoder cable, Power cable, Motion cable / MITSUBISHI, YASKAWA, MR N, PANS NIC,
LSIS, SAMSUNG, etc.
■ Wiring harness / Special cable assembly
※The above specifications are subject to change without notice.
※Please contact HQ or branch office where you purchased product for A/S of this product or technique.
❶XTB Series 7mm Pitch Interface terminal
❷No. of Poles
20 : 20P
26 : 26P
34 : 34P
40 : 40P
50 : 50P
❸Connector type
H : MIL-C-83503 Connector
(50P polarity guide : 2EA)
B : 50P polarity guide : 1EA( nly 50P)
XTB -40 H
❶❷❸Caution
1. When wiring, do not let any foreign material such as dust or cable sheath go into terminal.
It may cause damage, overheat or fire.
2. When wiring or handing, turn off the power.
※We are providing the connection cable for PLC per each ma er.
For detail on model and specification, refer to our catalog or contact us.
Connector Side
Terminal Side
Connector Side
Terminal Side
Connector Side
Terminal Side
HIF3BA-20PA-2.54DSA
60.080.0
40.5
7.0
14.0
40.8
40.8
• Wiring Diagram
A1B1
2143658710911131215141716191821202322252426
B2A2B3A3B4A4B5A5B6A6B7A7B8A8B9A9B10A10B11A11B12A12B13A13
101.0HIF3BA-26PA-2.54DSA7.0
40.514.0
81.0
• Wiring Diagram
Connector Side
Terminal Side
Connector Side
Terminal Side
● XTB-40H
฀

40.8128.0149.0HIF3BA-40PA-2.54DSA7.0
40.514.0
● XTB-50H/XTB-50B
• Dimension
• Dimension •XTB-50H
•XTB-50B
• Wiring Diagram
• Wiring Diagram
40.8
40.514.0
109.0129.0HIF3BA-34PA-2.54DSA7.0
13579111315171921232527293133246810121416182022242628303234
B1B2B3B4B5B6B7B8B9B10B11B12B13B14B15B16B17A1A2A3A4A5A6A7A8A9A10A11A12A13A14A15A16A17
● XTB-34H
• Dimension
● XTB-20H
• Dimension
●
XTB-26H
• Dimension
• Wiring Diagram
ABCDApplicablewireForkedMin. 4.1Max. 16.0Min. 3.0Max. 5.9AWG 22-16(0.30~1.25㎟)RoundMin. 4.1Max. 16.0Min. 3.0Max. 5.9ModelXTB-20HXTB-26HXTB-34HXTB-40HXTB-50HXTB-50BRatedvoltage125V AC / 24V DCRatedcurrent1ANumberofconnectors20Pin26Pin34Pin40Pin50Pin50PinNumberofterminals20ea26ea34ea40ea50ea50eaTerminalpitch7.0㎜ApplicablewiresAWG22-16 (1.5㎟ / MAX)Insulationresistance100MΩ (DC 500V)DielectricstrengthAC500V 1minScrewM3 X 8LScrewtorque1.2N·m (12kgf·cm)Ambienttemperature-10℃ ~ +50℃ (No freezing)MaterialCaseModifide PPOProtectivecoverPolycarbonatePCBEpoxy 1.6t(Unit : ㎜)