Iomega REV 35gb Assembly Instructions

1
REV™ 35gb
Removable Hard Disk Drive
Integrator Guide

2
Table of Contents
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
ATAPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Installing the Iomega REV Internal ATAPI Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Iomega REV Internal ATAPI Drive Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
SCSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Installing the Iomega REV Internal SCSI Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Iomega REV Internal ATAPI Drive Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Tech Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
About the Iomega REV System Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Troubleshooting the REV Internal SCSI Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

3
System Requirements
The following are the minimum system requirements for using a REV drive.
Supported Operating Systems
• Windows XP (Home and Professional)
• Windows Server 2003 (Standard and Small Business Editions)
• Windows 2000 Professional (SP3 and SP4)
• Windows 2000 Server (SP3 and SP4)
• Windows 2000 Advanced Server (SP3 and SP4)
Hardware Requirements
• 333 MHz processor, or higher
• Available 5.25" or 3.5" drive bay
• Available internal power connector
• 4X CD-ROM drive to use the Solutions CD
• 100MB hard drive space
• 128MB RAM
Additional Hardware Requirements for REV SCSI drive
• SCSI adapter card (68-pin SCSI only)

4
ATAPI
1
Install the REV System Software.
NOTE: See the “About the REV System Software” section of this guide for more
information.
2
Disconnect the power cord, and remove the cover to your computer. Verify that the
REV drive jumper settings are set to Cable Select as shown in the illustration.
NOTE: If you will be connecting another drive to the REV IDE data cable set the jumper
settings for that drive to cable-select.
Installing the Iomega REV Internal ATAPI Drive

5
ATAPI
3
Locate a vacant drive bay (5.25 " or 3.5 " drive bay) and remove the panel cover. Slide
the REV drive into the drive bay.
NOTE: If you are installing into a 5.25
" drive bay, you will need a mounting bracket
(available from your computer retailer).
4
Connect the black connector of the IDE data cable to the back of the REV drive
NOTE: For best performance, use the cable that shipped with the drive.

6
ATAPI
5
Connect the  blue connector of the IDE data cable to the secondary channel on the
motherboard and the  gray connector to another drive (optional).
NOTE: If the secondary channel already has a cable attached, replace with the IDE data
cable as shown here or see the User’s Manual for detailed instructions.
6
Connect a  spare power supply cable from the computer to the drive.
NOTE: If there is no spare power supply cable, you may need to purchase a Y-cable
power adapter.




7
ATAPI
7
Replace the cover, connect the power cord and restart your computer.
8
Confirm that your drive appears in the list by selecting Yes, and then select Close.
NOTE: If the detection software does not startup or you do not see your drive listed,
refer to the user’s manual on the CD for help.

8
ATAPI
35
GB /
90
Native/Compressed
GB
9
Insert a disk and your drive is now ready to use. The REV drive icon will display in My
Computer or Windows Explorer.
NOTE: If this package did not include a REV disk, you will need to purchase one.
Iomega REV Internal ATAPI Jumper Settings
 Cable Select (Default)
 Slave
 Master

9
SCSI
1
Install the REV System Software.
NOTE: See the “About the REV System Software” section of this guide for more
information.
2
Select an appropriate SCSI ID. The Iomega REV comes preset at SCSI ID 4.
You can use any SCSI ID that is not already in use by the computer or another device.
See the drive properties for information on the IDs of connected devices. ID 7 is
generally reserved for the SCSI adapter card.
Installing the Iomega REV Internal SCSI Drive

10
SCSI
Check the Term Power (Termination Power) setting of the REV drive.
Your SCSI chain must have a termination block (preinstalled on most cables) and at
least one device that provides termination power. The Iomega REV drive provides
termination power by default. If you do not want the REV drive to provide termination
power, remove the Term Power jumper.
Power down the computer. Disconnect the computer power cord and remove the
cover.
4
3