IOT-Smart Solutions MPTZ20XIRIP-ST Instruction Manual

MPTZ20XIRIP-ST
Manual operation
V4.5.1
Network HD IR High Speed PTZ Camera
http://iotsmartsolutions.net

PRECAUTIONS:
CAUTION
RISK OF ELECTRIC
SHOCK. DO NOT OPEN!
CAUTION:
TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO DOT
OPEN COVERS. NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
The lighting flash with a arrowhead symbol, in an
equilateral triangle, is intended to alert the user.
There is uninsulated “dangerous voltage” presence
near by the product's enclosure which may be risk of
to persons .
The exclamation point within an equilateral
triangle is intended to alert the user to reference
of the important op era tin g and mainten anc e
(servicing ) instructions .
THE PRODUCT CODE MARKED ON THE BOTTOM COVER. PLEASE
FILL THE CODE IN THE FOLLOWING BLANK. PLEASE SAVING
THIS SPECIFICATION CAREFULLY, SO THAT CHECKING.
MODEL:________________________
PRODUCT CODE:________________________
Please read the operation manual
Carefully before installing and using this product

Index
I. Important Safeguards…………………………………………………………………… 1
II. Description of Functions………………………………………………………………1
III. Setup of PTZ Camera…………………………………………………………………2
1. Protocol &PTZ address selecting……………………………………………2
2. Setup of Coding Switch of PTZ Camera …………………………………3
3. Setup of the Protocol and the Default Baud Rate………………………3
4. Setup of the Baud Rate of Communication………………………………4
5. Selection of the Terminal Resistor of the PTZ Camera………………4
6. Outline connecting socket description……………………………………4
IV. The installation of system……………………………………………………………5
V. Technical Parameter……………………………………………………………………7

1
I. Important Safeguards
1. All the safety and operating instructions should be read before the units is operated.
2. Power supply for HD IR PTZ Camera：DC12V. The power input power supply indicated on the
base of PTZ or other related marking label.
3. During the course of transportation, storage and installation, the product should be avoided
from incorrect operations such as heavy pressing, strong vibration etc., which can cause damage
of product as there are sophisticated optical and electronic devices inside the machine.
4. Do not attempt to disassemble the camera. In order to prevent electric shock, do not remove
screws or covers. There are no user-serviceable parts inside.
5. Always follow all electrical standards for safety when it is in operation. Adopt the particular
power supply, which is provided with the unit. RS-485 and video signal should keep enough
distance with high voltage equipments and cables when they are in transmission. Precautions
for anti-lightning and anti-surging should be taken if necessary.
6. Do not operate it in case temperature, humidity and power supply are beyond the limited
stipulations.
7. Do not let the camera aim at the sun or the object with extreme light whatsoever it is switched
on or not. Do not let the camera aim at or monitor bright and standstill object for a long time.
8. Do not use aggressive detergent to clean the main body of the camera. Wipe dirt with dry cloth.
If needed, mild detergent can be used suitably.
9. Operate the intelligent PTZ camera with great care to avoid shock or vibration. It operate
incorrectly, the PTZ could be damaged.
10.Please ensure the installation position with enough endurance when you install the intelligent
IR High speed PTZ camera.
11. If necessary, use a commercial lens cleaning paper to clear the lens windows. Gently wipe the
lens window until clean..
II. Description of Functions
The intelligent PTZ camera is a hi-tech CCTV product, which incorporates high-clarity color
camera, panoramic speed-variable PAN/TILT, multifunctional decoder, universal character
generator, CPU processor, memory chip into a whole. It can largely reduce connection and
installation processes of components in the system, rise up reliability of the system and facilitate
installation and maintenance. Therefore, it has advantages of beautiful appearance, compact
structure and easy operation.
1. Dome descriptions:
a. Pan 360º continuously rotation, manual pan control speed 0.1～100rad/s;Tilt range 0～
90º(It could be up to - 60°～90°without outer housing),Manual operation control speed
90°/s, pan preset speed max up to150°/s,tilt preset speed max up to 120°/s.
b. Running stably at low speed with super lower noise. Pictures have no shaking.
c. Automatic flip and panoramic monitoring without blind point, the location precision up
to ±0.1°.
d. It could setup 6 cruising tracks, 4 scanning commands, 1 patterns function.

2
e. Home position as tracking, patterns, presets
f. Memory function after power off, it automatically returns to the original station after
power on.
g. Built-in temperature sensor, with temperature display function, can control internal air
cooling system by manual or auto.
h. Coordination display function, the compass direction way could setup to the North.
i. PELCO-D coordination searching, coordination setup functions.
j. It stores 255 preset positions, data memorize after power off.
k. Proportional pan function, it could recognize many normal using cameras.
l. With wiper for the PTZ, it could solve the disadvantages side of cleaning camera lens.
m. IP Grade: IP66.
n. 4 Alarm input, 1 Alarm output (Optional).
o. It could analyze dome camera fault problem, some fault details information, such as
pan/tilt information, and self-testing information could be displayed on the screen.
p. IR lamp opening threshold could be adjusted. It could be used at different environment.
q. Infrared lights and cameras really achieve three-compartment isolation; completely solve
the infrared lamp rapidly aging and camera lens fog problem.
r. Constant current dimming design, more stable infrared lamp life up to 30,000 hours.
s. This PTZ applies with the 3rd generation high-power IR light, multiple angles with the
adjustable of brightness, could maximally achieve the best illumination.
t. 4 different IR lamp light compensation, it meets different requirement.
III. Setup of PTZ Camera
1. Protocol &PTZ address selecting
Diagram 1
2. Setup of Coding Switch of PTZ Camera .As diagram 1 shows，SW1 is used to set address of
the PTZ camera from 1 – 255. The coding switches from DIP-8 to DIP-1 are equivalent to a 8-bit
binary digital. DIP-8 is MSB while DIP-1 is LSB. The state “ON” of each bit means 1 while
“OFF” means 0. Following table shows states of coding switches of some addresses.
PTZ address selecting
SW1：DIP1—DIP8 selecting address
DIP10: 120
Ω
Resistor to selecting
Protocol selecting
SW1
SW2

3
1
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
4
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
5 ON OFF ON OFF OFF OFF OFF OFF
6 OFF ON ON OFF OFF OFF OFF OFF
7 ON ON ON OFF OFF OFF OFF OFF
8 OFF OFF OFF ON OFF OFF OFF OFF
9 ON OFF OFF ON OFF OFF OFF OFF
10 OFF ON OFF ON OFF OFF OFF OFF
11
ON
ON
OFF
ON
OFF
OFF
OFF
OFF
12
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
13
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
14
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
15 ON ON ON ON OFF OFF OFF OFF
16 OFF OFF OFF OFF ON OFF OFF OFF
17 ON OFF OFF OFF ON OFF OFF OFF
18 OFF ON OFF OFF ON OFF OFF OFF
… … … … … … … … …
255 ON ON ON ON ON ON ON ON
Table 1
For example：
Speed Dome Address=1
ON
1 2 3 4 5 6 7 8 9 10
Speed Dome Address=2
ON
1 2 3 4 5 6 7 8 9 10
Speed Dome Address=3
ON
1 2 3 4 5 6 7 8 9 10
Speed Dome Address=4
ON
1 2 3 4 5 6 7 8 9 10
Speed Dome Address=18
ON
1 2 3 4 5 6 7 8 9 10
Speed Dome Address=512
ON
1 2 3 4 5 6 7 8 9 10
3. Setup of the Protocol and the Default Baud Rate. As figure 1shows, SW2 is used to set the
protocol of communication and the baud rate used by the PTZ camera. DIP-4 to DIP-1 of SW2
is used to select protocols.
Protocols DIP Status Normal Baud Rate
DIP-1
DIP-2
DIP-3
DIP-4
DIP-5
DIP-6
PELCO-D OFF OFF OFF OFF OFF OFF
PELCO-P OFF ON OFF OFF OFF OFF
Tablet 2
4. Setup of the Baud Rate of Communication. As shown in Figure 1, SW2 is used to set the
Dome
Address
Coding Switch Status
DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6 DIP-7 DIP-8

4
protocol of communication and the baud rate used by the PTZ camera. DIP-6 and DIP-5 of SW2
are used to select the baud rate of communication and 4 different baud rates can be selected in
maximum. If the controller adopts non-standard baud rate, you can adjust it to be identical with
that of the main machine as per the following table.
Baud Rate of Communication
Setup of Baud
Rate
DIP-1
DIP-2
DIP-3
DIP-4
DIP-5
DIP-6
2400bps
OFF
OFF
4800bps ON OFF
9600bps OFF ON
19200bps ON ON
5. Selection of the Terminal Resistor of the PTZ Camera. As shown in Figure 1, SW1is the
select switch of the 120 Ω terminal resistors on the bus RS485, on which only one terminal
resistor of the dome camera at the farthest end can be connected, while the terminal resistors of
other devices should be opened. Dip 10 turns ON of SW1,it means 120 Ω resistor turns ON; Dip
10 turns OFF of SW1.it means 120 Ω resistor turns OFF.
6.Outline connecting socket description：
A．10-pin input connecting socket
6.1 10-pin input connecting socket description：
1．NET_TX-2．NET_RX+
3．NET_TX+ 4．Video output(CVBS)
5．GND 6．POWER-
7．POWER+ 8．NET_RX-
9．RS
485+
10．RS
485-
IV. The installation of system
1. Installing ways
1）Dimension(IR Version)

5
2. Dimension for shock absorber
2. Installing steps
1. Please carefully take out the PTZ and accessories from package.
2. You may cancel Step 2, and Step3 if protocol and address don’t need to change
3. As Diagram 2 shows, please setup the related protocol according to table 2 shows. And please
ensure if the PTZ address is matched with your requiring address, if it’s not matched; please setup
according to the table 1.
Diagram 2
Dimension for shock absorber

6
4. If it uses on car surveillance, please put the absorber on the surface of the shock absorber, then
fix the total PTZ on the shock absorber components, here it also needs 4 pieces M8X25 outer
hexagonal screws, 4 piecesφ8 spring washers,4 piecesφ8 flat washers,4 piecesM8 nut.
5. Please connect the socket outlet correctly according to the related wire color, and avoid any
mistake of connecting wire.
Notes: Please connect the related adaptor according to the actual using situation: DC power supply
input could be recommended as car surveillance.
Shock absorber
12V installing way

7
V. Technical Parameter
PTZ function
Pan range 360°contimuously rotation
Pan speed
Pan control speed
：
0.1°-100°/s,
Pan preset speed：150°/s
Tilt range -60°- 90°
Tilt speed Tilt speed：0.1°-90°/s,
Tilt preset speed：120°/s
Proportional pan function Support
Preset positions 255
Cruising scanning 6, each with 16 preset positions
Patterns function 4, pattern direction and speed could adjust
Self-studying function 1 with 200 seconds
Memory after power off Support
Home position Presets /Tracking/ Pan scanning
Coordination display Support
Temperature display Support
Compass function Support, the North direction could be setup
Wiper function Support jog and linkage mode
Power supply DC10.8V-DC18V
Consumption 50W (Max)（IR lamp 20W Max，Heater 5W Max）
Temperature and humidity -30 ℃- 65℃humidity less than 90%
IP Grade IP66(Outdoor)TVS 4000V lightning、anti-surge protection
Installing way Different installing ways accordingly(Support car surveillance)
Weight 6kg
IR function IR range 60m
IR lamp consumption 8W