IP DOOR ENTRY BATICONNECT IPGUARD MINI User manual

4G/IP/GSMSMART VISITOR ENTRY PANEL
INSTALLATION MANUAL
4G/IP/GSM SMART
Visitor Door Entry
IPGUARD MINI IPGUARD MINI PLUS IPGUARD MINI TOUCH
IPGUARD®& BATICONNECT®

4G/IP/GSM SMART
Visitor Door Entry INSTALLATION CABLING
1
-
+
E1
GND
D2D2
SIM
CARD
-
+
-
+
2
1
E2
C
NC
RJ45
NO
EXIT BUTTON
RESET
BUTTON
POWER IN
3-core 1.5mm² flex cable (3183Y)
12VDC / 5A
EVE196-X3-RS
PROXIMITY
CONTROL
UNIT
(Only used if integral proximity reader
and EVE196-X3-RS control unit is not used)
LOCK OUTPUT RELAY
Lock circuit cable ref.
4 x 1 YY/LSZH per lock
(4-core, 1mm²/core)
INTERNAL OR
EXTERNAL AERIAL
LOCK RELAY 1
12VDC
TRIGGER
RELAY 1
4G/IP ROUTER CONNECTION
Class E (CAT6) U/UTP
(Option 2. Only required if 4G
aerial needs to go on the roof)
PRE-INSTALLED
Class E (CAT6) U/UTP IPGUARD PANEL
IPGUARD PANEL
TOP
4G/IP ROUTER
CONNECTION
(OPTIONAL)
SIM CARD
EVE196-X3-RS
CONNECTION
EXIT BUTTON
POWER IN
LOCK OUTPUT
RELAY 1
RESET
BUTTON
INTERNAL OR
EXTERNAL
AERIAL
SCREW ON
CONNECTOR
Unscrew nut to remove internal default aerial and
screw-on the external aerial cable in its place.
INTERNAL
AERIAL
ZAN1055 external
remote aerial. Used if
4G signal to the panel
is low, or simply to
improve signal strength
Supplied with 5 metres
of cable.

4G/IP/GSM SMART
Visitor Door Entry INSTALLATION CABLING
2
-
+
E1
GND
D2
SIM
CARD
-
+
E2
C
NC
RJ45
NO
INTERNAL OR
EXTERNAL AERIAL
12VDC
TRIGGER
RELAY 1
PROXIMITY READER
CONTROL UNIT
12V DC ELECTRIC
FAIL SECURE RELEASE
EXIT
BUTTON
IPGUARD PANEL
AR125
AR122
EVE196-X3-RS
LOCK RELAY 1*
-
+
-
+
+NO C NC 4 5 6 7 8 9-
D2D1
EXIT
BUTTON
COAX
PROX
LOCK OUTPUT
RELAY
12VDC
Class E (CAT6) U/UTP
1 2
+ -
3-core 1.5mm2 ex cable (3183Y)
+
-
VARISTOR
OR DIODE
4 x 1 YY/LSZH per lock
(4-core, 1mm2/core)
AR125 (12VDC/5A)
for IPGUARD
and EVE196-X3-RS
AR122 (12VDC/2A)
for locking
IPGUARD PANEL WITH INTEGRAL PROXIMITY READER
FAIL SECURE LOCKING
*The lock relay output on the EVE196-X3-RS
is normally used to control the lock.
*The EVE196-X3-RS used for the IPGUARD
needs to have the RS485 protocol 5.

4G/IP/GSM SMART
Visitor Door Entry INSTALLATION CABLING
3
-
+
E1
GND
D2
SIM
CARD
-
+
E2
C
NC
RJ45
NO
12VDC
TRIGGER
RELAY 1
PROXIMITY READER
CONTROL UNIT
12V DC MAGNET
OR FAIL SAFE RELEASE
EXIT
BUTTON
IPGUARD PANEL
AR125
AR122
EVE196-X3-RS
EMEX
If your fail safe locking requires an Emergency Breakglass
Exit Device (EMEX with a normally closed contact) to
comply with Building Safety regulations, please t as shown.
LOCK RELAY 1*
INTERNAL OR
EXTERNAL AERIAL
-
+
-
+
+NO C NC 4 5 6 7 8 9-
D2D1
EXIT
BUTTON
COAX
PROX
LOCK OUTPUT
RELAY
12VDC
Class E (CAT6) U/UTP
1 2
+ -
3-core 1.5mm2 ex cable (3183Y)
+
-
VARISTOR
OR DIODE
4 x 1 YY/LSZH per lock
(4-core, 1mm2/core)
IPGUARD PANEL WITH INTEGRAL PROXIMITY READER
FAIL SAFE LOCKING
*The lock relay output on the
EVE196-X3-RS is normally
used to control the lock.
AR122 (12VDC/2A)
for locking
EVE196-X3-RS’s connected to the
IPGUARD need to be programmed
as the rst in the chain (i.e RS485
address =1).
Each IPGUARD & EVE196-X3-RS
needs to be installed in their own bus
chains/network (not wired together).
AR125 (12VDC/5A)
for IPGUARD
and EVE196-X3-RS

4G/IP/GSM SMART
Visitor Door Entry INSTALLATION CABLING
4
The EVE196-X3-RS’s connected to the IPGUARD need to be
programmed as the first in the chain (i.e RS485 address =1)
Each IPGUARD and EVE196-X3-
RS needs to be installed in their
own bus chain/network (not
wired together).
The network/chains are
programmed and linked
together in the cloud via
www.baticonnect.com
RS485 = 1 ✔
RS485 = 1 ✔RS485 = 2 ✘
RS485 = 1 ✔
✘✘
✔✔

4G/IP/GSM SMART
Visitor Door Entry INSTALLATION CABLING
5
EVE196-X3-RS PROXIMITY READER CONTROL UNIT
FOR PROXIMITY READER INTERNAL TO IPGUARD PANEL
+NO C NC 4 5 6 7 8 9-
D2D1
EXIT
BUTTON
COAX
PROX
LOCK OUTPUT
RELAY
POWER FOR EVE196-X3
(NOT FOR LOCKING)
12VDC / 2AMP POWER
3-core 1.5mm
ex cable (3183Y)
EXIT
BUTTON
12VDC
Class E (CAT6) U/UTP
EVE196-X3
1 2
+ -
+-
EVE196-X3-RS
(Network address 01)
TOP
IPGUARD PANEL
BOTTOM
EXIT BUTTON
D2 ON IPGUARD
12VDC / 5AMP POWER
LOCK
OUTPUT
RELAY*
- +
*The lock relay output on the EVE196-X3-RS
is normally used to control the lock.

4G/IP/GSM SMART
Visitor Door Entry INSTALLATION CABLING
6
EVE196-X3-RS PROXIMITY READER CONTROL UNIT
WITH MLP8-RS PROXIMITY READER ANTI-VANDAL
EXTRA PROX
DOORS ONLY
+NO C NC 4 5 6 7 8 9-
D2D1
D2
D1
EXIT
BUTTON
COAX
PROX
LOCK OUTPUT
RELAY
POWER FOR EVE196-X3-RS
(NOT FOR LOCKING)
12VDC / 2AMP POWER
3-core 1.5mm
ex cable (3183Y)
EXIT
BUTTON
12VDC
+-+-
12VDC
Class E (CAT6) U/UTP Class E (CAT6) U/UTP
RS PROXIMITY READER
EVE196-X3-RS
CONTROL UNIT
NEXT EVE196-X3-RS
ON NETWORK
1 2
+ -
Class E (CAT6) U/UTP
NEXT EVE196-X3-RS
EVE196-X3-RS
1 2
+ -
LPERS
All proximity readers are installed in the same manner (LPERS, LPMRS and LPTRS)
*The EVE196-X3-RS used for the PROXIMITY READER needs to have the RS485 protocol 3.

4G/IP/GSM SMART
Visitor Door Entry INSTALLATION CABLING
7
NETWORKING EXTRA DOORS ONTO IPGUARD PANEL
-
+
E1
GND
D2
RT
ON OFF
SIM
CARD
-
+
E2
C
NC
RJ45
NO
LOCK RELAY 1
12VDC
TRIGGER
RELAY 1
IPGUARD PANEL
DOOR 1
IPGUARD DOOR
(Network address 01)
DOOR 4
(Network address 04)
DOOR 2
(Network address 02)
DOOR 3
(Network address 03)
LAST DOOR
+NO C NC 4 5 6 7 8 9-
D2
EXIT
BUTTON
COAX
PROX
COAX
PROX
COAX
PROX
COAX
PROX
LOCK OUTPUT
RELAY
12VDC
EVE196-X3-RS CONTROL UNIT FOR
PROXIMITY READER INTEGRAL TO IPGUARD
Class E (CAT6) U/UTP
Class E (CAT6) U/UTP
1 2
+ -
+NO C NC 4 5 6 7 8 9-
D2
EXIT
BUTTON
LOCK OUTPUT
RELAY
12VDC
EVE196-X3-RS CONTROL UNIT
Class E (CAT6) U/UTP
1 2
+ -
+NO C NC 4 5 6 7 8 9-
D2
EXIT
BUTTON
LOCK OUTPUT
RELAY
12VDC
EVE196-X3-RS CONTROL UNIT
Class E (CAT6) U/UTP
Fit a 120Ω (OHM) resistor
1 2
+ -
+NO C NC 4 5 6 7 8 9-
D2
D1
D1
D1
D1
EXIT
BUTTON
120Ω
LOCK OUTPUT
RELAY
12VDC
EVE196-X3-RS CONTROL UNIT
1 2
+ -
INTERNAL OR
EXTERNAL AERIAL
PRE-PROGRAMMED by IP
Door Entry ltd as Door 1,
Door 2, Door 7 etc.
Trained installers equipped
with TELU programmer
can program default
EVE196-X3-RS door
setting themselves. All
actual system operational
programming is via
www.baticonnect.com
When networking multiple
doors to the IPGUARD,
switch on RT on the
IPGUARD’s board.
Maximum 10 doors per IPGUARD®
panel. Additional doors can be added
by creating additional networks in
conjunction with our IGSM data modems.
At the end of the bus chain / network, YOU MUST add resistance
either by switching on RT2 on the last EVE only or by adding a
120 (OHM) resistor, as shown above.

4G/IP/GSM SMART
Visitor Door Entry INSTALLATION CABLING
8
FOR
INFORMATION
ONLY
NO C NC 4 5
+-
12V DC MAGNET
OR FAIL SAFE RELEASE
VARISTOR
OR DIODE
EXIT BUTTON
EMEX
LOCK OUTPUT RELAY
If your fail safe locking requires an Emergency
Breakglass Exit Device (EMEX with a normally
closed contact) to comply with Building Safety
regulations, please t as shown.
TO +
+
-
12VDC/2AMP
DEDICATED PSU
EVE196-X3-RS CONTROL UNIT
FAIL SECURE LOCKING
EVE196-X3-RS CONTROL UNIT
AUTOMATION CONTROL / VOLT-FREE
EVE196-X3-RS CONTROL UNIT
FAIL SAFE LOCKING
NO C NC 4 5
+
-
12V DC
FAIL SECURE
ELECTRIC RELEASE
VARISTOR
OR DIODE
EXIT BUTTON
12VDC/2AMP
DEDICATED PSU
FOR
INFORMATION
ONLY
TO +
+ -
FOR
INFORMATION
ONLY
NO C NC 4 5
TO AUTOMATION
CONTROL
EXIT
BUTTON
IMPORTANT!
1. A diode or varistor must be
tted across the lock power
terminals as clearly shown.
2. Use separate power supplies
for (a) the electric locking
(b) the IPGUARD panel.
3. The IPGUARD back box and/or
any metal work connected to
the IPGUARD must be earthed.
Failure to comply invalidates all
warranties.

4G/IP/GSM SMART
Visitor Door Entry INSTALLATION CABLING
9
NO
C
NC
+
-12V DC FAIL SECURE
ELECTRIC RELEASE
VARISTOR
OR DIODE
LOCK OUTPUT
RELAY
FOR
INFORMATION
ONLY
TO +
+ -
12VDC/2AMP
DEDICATED PSU
FOR
INFORMATION
ONLY
NO
C
NC
VARISTOR
OR DIODE
LOCK OUTPUT
RELAY
+
-
12V DC MAGNET OR
FAIL SAFE RELEASE
If your fail safe locking requires an Emergency
Breakglass Exit Device (EMEX with a normally
closed contact) to comply with Building Safety
regulations, please t as shown.
EMEX
TO +
+ -
12VDC/2AMP
DEDICATED PSU
FOR
INFORMATION
ONLY
NO
C
NC
LOCK OUTPUT
RELAY
TO AUTOMATION
CONTROL
FAIL SECURE LOCKING
IPGUARD RELAY 1
FAIL SAFE LOCKING
IPGUARD RELAY 1
AUTOMATION CONTROL / VOLT-FREE
IPGUARD RELAY 1