IPitomy IPR20 User manual

IPR20 Quick Start Guide
The IPR20 is a 2 Port VoIP Gateway. IPitomy’s IPR20 connects two
analog phones to your IP network to allow VoIP calls or allows you to
setup a dedicated DID for faxing. The IPR20 comes with 2 FXS ports,
one WAN port and one LAN port.
5 Easy Steps to configure the IPR20
Connecting the IPR20
Creating extensions on the PBX
Registering the IPR20 with the PBX
Creating users on the IPR20
(Optional) Configuration of DID on the PBX for fax service
1)
2)
3)
4)
5)
www.ipitomy.com | 941.306.2200

IPR20 LED Indicators
LED Label Description
10/100 Ethernet WAN
LAN
On Link Up
Off Link Down
Flashing Sending / Receiving
Data Packets
Loop / Ring FXS Phone 1
FXS Phone2
On Off Hook
Off On Hook
Flashing Ring Out
Device Power On Indicates Power
Supply is Working
Off
Ports Label Description
Voice Ports Phone 1
Phone 2
Connects to a telephone or fax machine
Connects to a telephone or fax machine
Ethernet Ports Wan RJ-45 Connector
MDI-X Connects to a modem
Lan RJ-45 connector
MDI connects to a PC or local network
Power 12 V/DC Input: 12V DC
Reset RESET Reset System
IPR20 Back Panel

Typical Small Office Configuration

Connecting the IPR20
Connect a PC with a RJ-45 cable to the IPR20’s LAN port
On the connected PC open a web browser and navigate to 192.168.1.1
Username: admin
Password: voip
If the main network is already a 192.168.1.xxx network you must change
the LAN subnet of the IPR20. Leave the WAN side set to DHCP or
assign the WAN port a static IP address on the main network.
After configuring the IP scheme of the IPR20:
Connect a RJ-45 cable from your local network to the IPR20’s WAN port.
1)
2)
3)
4)
1

Creating Extensions on the PBX
Log into the IPitomy PBX
Under Destinations > Extensions click add new
Configure an extension or 2 extensions for the IPR20 (see PBX
manual for how to configure extensions) leave phone type as generic
and make note of your USERNAME and SIP PASSWORD
Save Changes > Apply Changes
1)
2)
3)
4)
2

Registering the IPR20 with the PBX
Log into the IPR20 ex (192.168.1.1) if you are on the LAN side
(DHCP address or static address if on WAN side)
Go to SIP > Server
*Address, Domain Name and Outbound Proxy IP are the IP address of the PBX to be registered with
*Port and Outbound Proxy Port is the standard 5060
Save SIP Settings
Restart IPR20
1)
2)
3)
4)
3

Setting Users on the IPR20
Go to SIP > User1 and/or User2
*User Name is the extension number used for this user
*Password is the sip password configured in the PBX
Save SIP Settings
Restart IPR20
The status light on the IPR20 should be solid green if
a connection to the PBX was established
1)
2)
3)
4)
4

Configuring a DID for FAX service
Log into the PBX
Go to providers
Choose either a) SIP Providers or b) Hardware Trunks (this is determined by what
provider you want to associate your DID FAX number with)
a) if using a T1 line choose your associated card and select add a line
b) if using a SIP provider choose edit on the proper associated provider
At the bottom of the page add your DID number (for detailed information
on adding a DID please refer to the PBX documentation)
Under the destination drop down list for you DID choose the extension created
for the user on the IPR20 that will be connected to the FAX machine
Set the destination and Save Changes > Apply Changes
1)
2)
3)
4)
5)
6)
5