IR-Tec OS-NET ON-PBD-815 User manual

The ON-PBD-815 is an optional device of IR-TEC’s OS-NET
wireless mesh network solution. This device is exclusively
designed to replace an existing wall switch/dimmer to
broadcast manual on/off/dim control commands to the
assigned group lighting, while also function as a network
node.
This sleek, low profile OS-NET device can be mounted into a
standard EURO wall box, operated by line voltage power, and
provide wireless control to the grouped lighting as required.
Each ON-PBD-815 can be assigned to control up to 4 lighting
groups via a 2-way handheld remote programmer.
A short press at upper/lower position of the button will
transmit a command to switch on/off the lighting of groups
assigned. Press and hold at upper/lower position of the
button will increase/decrease the output level of controlled
lighting respectively. A screwless snap-on wall plate is
supplied to create a modern, high-end appearance for all
spaces. By grouping the ON-PBD-815 with OS-NET sensors
and controllers, you can effortlessly achieve an
energy-efficient, code-compliant smart lighting control
through a state-of-the-art wireless sensor mesh network with
manual controls capability for presentation or special event.
Line Voltage OS-NET Button
INSTALLATION INSTRUCTIONS
OVERVIEW
P/N: Z50-00334-000www.irtec.com
This product may be covered by one or more U.S. patents or patent applications.
Please visit www.irtec.com for more information.
ON-PBD-815
Lead the wires and strip the insulation with proper
length for connecting.
Connect the wires with the device according to the
wiring diagram shown above.
NOTE: The ON-PBD-815 requires connecting neutral
wire for operation. To replace the existing wall switch
with no neutral wire, you may substitute the switched
line wire for the neutral of lighting in accordance with
electrical codes and regulations.
Carefully set the wires and mount the device into the
wall box with screws provided.
NOTE: Do NOT mount the device upside down.
INSTALLATION
1.
2.
3.
INDOOR USE ONLY
Utilisation a L'interieur Uniquement
AVERTISSEMENT & PRUDENCE
WARNING & CAUTION
Turn power OFF at circuit breaker before installing .
Coupez l'alimentation au disjoncteur avant d'installer.
Unit: mm
30 86
86
72
60
72
54
DIMENSIONS
WIRING DIAGRAM
L
230VAC
N
PRELIMINARY
N L

OPERATION
SPECIFICATIONS
A SHORT press (≤0.5 second) at the UPPER part of button
will transmit a command to turn on the grouped lighting.
Light will stay on as long as the grouped sensor(s) detects
the occupancy, and the grouped sensor/controller will
resume control after the area is vacated.
A short press at upper/lower position of the button will
transmit a command to turn on/off the lighting of groups
assigned. Press and hold at upper/lower position of the
button will increase/decrease the output level of grouped
lighting respectively.
1. Turn On the light
A SHORT press (≤0.5 second) at the LOWER part of button
will transmit a command to turn off the grouped lighting. The
grouped sensor/controller will resume control after the delay
time elapsed.
2. Turn Off the light
A LONG press (≧0.5 second) at the UPPER part of button
will enter into dimming adjustment mode to increase the
output level of grouped lighting. Intermittent press on the
button during dimming control mode will adjust the output
level step by step. The device will exit from dimming
adjustment mode 2 seconds after the last button operation.
3. Ramp up the light
A LONG press (≧0.5 second) at the LOWER part of button
will enter into dimming adjustment mode to decrease the
output level of grouped lighting. Intermittent press on the
button during dimming control mode will adjust the output
level step by step. The device will exit from dimming
adjustment mode 2 seconds after the last button operation.
NOTE: After changing the dim level, allow the LED bar to
turn off before trying to switch on/off
4. Fade down the light
Power voltage
Wireless protocol
Radio frequency
Radio range
Op. humidity
Op. temperature
Dimensions
230VAC, 50/60 Hz
Modified Zigbee Light Link (ZLL)
2.4 GHz
Typical 15 m @indoor
Max 95% non-condensation
-10°C ~ 50°C (-14°F ~ 122°F)
72H x 72W x 38D mm (w/mounting plate)
IR-TEC International Ltd. warranties this product to be free of
defects in materials or workmanship for a period of five years
from date of shipment. There are no obligations or liabilities
on the part of IR-TEC International Ltd. for consequential
damages arising out or in connection with the use or
performance of this product or other indirect damages with
respect to loss of property, revenue, profit, or cost of removal,
installation or reinstallation.
WARRANTY
www.irtec.com
After installing completed, the
ON-PBD-815 requires grouping to
link with the OS-NET network. To
group and link the device, you
would need an SRP-281 OS-NET
Remote Programmer to conduct
the grouping process by pointing
toward the target device. Refer to
the OS-NET Programming Guide
available from www.irtec.com for more details about
grouping procedures.
NOTE: Grouping data can be read on the remote by
conducting a download process with the remote face to the
device.
GROUP LINK
Programming Guide