IR-Tec ON-PBD-705 Series User manual

The ON-PBD-705 series is an optional device of IR-TEC’s
OS-NET wireless mesh network solution designed to
replace an existing wall switch/dimmer and broadcast
manual on/off/dim control commands to the lighting group
assigned.
This sleek, low profile device can be mounted into a
standard NEMA wall box, operated by line voltage power,
and provide wireless control required by users. Each
ON-PBD-705 can be assigned to control up to 4 lighting
groups via a 2-way handheld remote programmer.
A screwless snap-on Decora wall plate is supplied to create
a modern, high-end appearance for all spaces. By grouping
the ON-PBD-705 with OS-NET sensors and controllers, you
can effortlessly achieve an energy-efficient, code-compliant
smart lighting control through a state-of-the-art wireless
sensor mesh network with manual controls capability for
presentation or special event.
OVERVIEW
www.irtec.com
This product may be covered by one or more U.S. patents or patent applications.
Please visit www.irtec.com for more information.
Lead the wires and strip the insulation with proper
length for connecting.
Connect the wires with the device according to the
wiring diagram shown above.
NOTE: The ON-PBD-705 requires connecting neutral
wire for operation. To replace the existing wall switch
with no neutral wire, you may substitute the switched
line wire for the neutral of lighting in accordance with
electrical codes and regulations.
Carefully set the wires and mount the device into the
wall box with screws provided.
INSTALLATION
1.
2.
3.
NOTE: Do NOT mount the device upside down.
INDOOR USE ONLY
Utilisation a L'interieur Uniquement
AVERTISSEMENT & PRUDENCE
WARNING & CAUTION
Risk of Electrical Shock – Turn off the power at circuit breaker
before installing or servicing.
This device should be installed by a qualified electrician in
accordance with electrical codes and regulations.
Risque de choc électrique - Débranchez l'alimentation avant
l'entretien.
Installer et utiliser ce dispositif conformément aux codes et
règlements électriques.
Line Voltage OS-NET Button
ON-PBD-705 series
INSTALLATION INSTRUCTIONS
PRELIMINARY
WIRING DIAGRAM
Black
White
Line
120/277VAC Green
Ground
Neutral
UP
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
Federal Communication Commission Interference
Statement
P/N: 058-50911-002 Printed in Taiwan

OPERATION
IR-TEC International Ltd. warranties this product to be free of
defects in materials or workmanship for a period of five years
from date of shipment. There are no obligations or liabilities
on the part of IR-TEC International Ltd. for consequential
damages arising out or in connection with the use or
performance of this product or other indirect damages with
respect to loss of property, revenue, profit, or cost of removal,
installation or reinstallation.
WARRANTY
www.irtec.com
After installing completed, the
ON-PBD-705 requires grouping to
link with the OS-NET network. To
group and link the device, you
would need an SRP-281 OS-NET
Remote Programmer to conduct
the grouping process by pointing
toward the target device. Refer to
the OS-NET Programming Guide
available from www.irtec.com for more details about
grouping procedures.
NOTE: Grouping data can be read on the remote by
conducting a download process with the remote face to the
device.
GROUP LINK
A short press at upper/lower position of the button will
transmit a command to turn on/off the lighting of groups
assigned. Press and hold at upper/lower position of the
button will increase/decrease the output level of grouped
lighting respectively.
1. Turn On the light
A SHORT press (≤0.5 second) at the UPPER part of button
will transmit a command to turn on the grouped lighting.
Light will stay on as long as the grouped sensor(s) detects
the occupancy, and the grouped sensor/controller will
resume control after the area is vacated.
2. Turn Off the light
A SHORT press (≤0.5 second) at the LOWER part of button
will transmit a command to turn off the grouped lighting.
The grouped sensor/controller will resume control after the
delay time elapsed.
3. Ramp up the light
A LONG press (≧0.5 second) at the UPPER part of button
will enter into dimming adjustment mode to increase the
output level of grouped lighting. Intermittent press on the
button during dimming control mode will adjust the output
level step by step. The device will exit from dimming
adjustment mode 2 seconds after the last button operation.
4. Fade down the light
A LONG press (≧0.5 second) at the LOWER part of button
will enter into dimming adjustment mode to decrease the
output level of grouped lighting. Intermittent press on the
button during dimming control mode will adjust the output
level step by step. The device will exit from dimming
adjustment mode 2 seconds after the last button operation.
NOTE: After changing the dim level, allow the LED bar to
turn off before trying to switch on/off.
SPECIFICATIONS
Power voltage
Wireless protocol
Radio frequency
Radio range
Op. humidity
Op. temperature
Dimensions
120/277VAC, 50/60 Hz
Modified Zigbee Light Link (ZLL)
2.4 GHz
Typical 50 ft. @indoor
Max 95% non-condensation
-14°F ~ 122°F (-10°C ~ 50°C)
4.13”H x 1.77”W x 1.65”D (w/mounting plate)
DIMENSIONS
3.81”
3.28”
4.13”
2.75”
1.22” 2.73”
1.77”
4.47”
Programming Guide