Ironton 5000G User manual

Thank you very much for choosing an IRONTON™ product! For future reference, please complete
the owner’s record below:
Model: _______________ Purchase Date: _______________
Save the receipt, warranty and these instructions. It is important that you read the entire manual
to become familiar with this product before you begin using it.
This machine is designed for certain applications only. The distributor strongly recommends this
machine is not modified and/or used for any application other than that for which it was
designed. If you have any questions relative to a particular application, DO NOT use the machine
until you have first contacted the distributor to determine if it can or should be performed on the
product.
For technical questions and replacement parts, please call 1-800-222-5381.
TECHNICAL SPECIFICATIONS
Measurements in three modes: grams, ounces and pounds
Max. capacity: 5000g, 176 oz., 11 lbs.
Weighing Increments: 1g, 0.01 oz., 0.001 lb.
Scale construction: ABS
Platform construction: Tempered glass
Platform diameter: 5 7/8in.
Operates on one lithium button cell CR2032 (included).
GENERAL SAFETY REGULATIONS
WARNING: Read and understand all instructions.
WARNING: The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions or situations that could occur. It must be
understood by the operator that common sense and caution are factors that cannot be built
into this product, but must be supplied by the operator.
• Keep the work area clean and dry. Damp or wet work areas can result in damage to the
product.
• Keep children away from work area. Do not allow children to handle this product.
• Always wear ANSI-approved safety glasses and heavy-duty work gloves during assembly
and use. Do not wear loose clothing or jewelry, which can get caught in moving parts.
•Store idle equipment. When not in use, tools and equipment should be stored in a dry
location to inhibit rust. Always lock up tools and equipment, and keep out of reach of children.
• Use the right tool for the job. Do not attempt to force small equipment to do the work of
larger industrial equipment. There are certain applications for which this equipment was
designed. It will do the job better and more safely at the capacity for which it was intended.
Do not modify this equipment, and do not use this equipment for a purpose for which it was
not intended.
• Check for damaged parts. Before using this product, carefully check that it will operate
properly and perform its intended function. Check for damaged parts and any other
conditions that may affect the operation of this product. Replace damaged or worn parts
immediately.
• Do not overreach. Keep proper footing and balance at all times to prevent tripping, falling,
back injury, etc.
• DO NOT use the equipment when tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating this equipment may result in serious
personal injury.
• Industrial applications must follow OSHA requirements.
5000G (11 LB.) GLASS DIGITAL SCALE
USER’S MANUAL
5000G (11 LB.) GLASS DIGITAL SCALE
USER’S MANUAL
WARNING:
Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS
before operating. Failure to follow the safety rules and other basic safety
precautions may result in serious personal injury.
Item# 30737
1 of 3

GUIDE TO SAFETY OPERATION
WARNING: The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions or situations that could occur. It must be
understood by the operator that common sense and caution are factors that cannot be built
into this product, but must be supplied by the operator.
(1) Use the scale on a clean and flat table or other level surface.
(2) Do not overload the scale. 5000g/ 176 oz./ 11 lbs. is the maximum allowable weight before
you tare the containers.
(3) Do not apply excessive pressure or drop the scale. Use the scale with care to prevent
damage.
(4) Use soft cloth to clean the scale. Water or any chemical detergent can easy go inside the
scale and damage it.
(5) Check the condition of battery and the touch point of platform contacts well with the
scale body if the scale doesn’t work.
(6) Replace depleted batteries as soon as possible. Replacement batteries (CR2032) are
available from the distributor.
(7) This scale is designed for household use only. Not for commercial use.
OPERATION INSTRUCTIONS
1. Key Function
(1) Function of the ON/TARE key: Power on,
Power off, Tare
(2) Function of UNIT key: Unit exchange
between g, oz. and lb.
2. Battery Replacement
When installing or replacing the battery,
please open the cover on the bottom, and
install/ replace the battery with one CR2032
lithium button cell properly. Re-place cover
before operation.
3. Operation
NOTE: Do not overload the scale.
Place the scale on a flat table with the button
cell on. Make sure it is steady before opera-
tion.
(1) Press ON/TARE key to power on, the
display flashes ”88888” for about 3 seconds
before it goes to standby and shows 0.
(2) Press UNIT key to change the unit between
g, oz. and lb.
(3) Put item onto the platform, display shows
the total weight of the item.
5000G (11 LB.) GLASS DIGITAL SCALE
USER’S MANUAL
5000G (11 LB.) GLASS DIGITAL SCALE
USER’S MANUAL
2 of 3
(4) Tare Deduction:
①. Put the container on the platform, it
displays the weight of the container.
③. Put item into the container, display shows
the net weight of the item.
②. Press ON/TARE key, the number of the
weight is zero. If you take the vessel away,
the number of the weight will be negative.
4. Error Display
(1) If the display will show "0-ld", it indicates
that the scale is overloaded.
(2) If the display shows "LO", it indicates that
the power is low and it is time to replace
the battery.
(3) If the display shows "OUT2" and the power
is off, it indicates that the scale is unsteady
or overloaded.
3 of 3
WARRANTY
1-year limited warranty
88888
UNIT TARE
ON
(1) (2)
88888 0 g
0g
89 g
23 g
66 g
0g23 g
-
0.00oz
0.000 lb
BATTERY
Distributed by:
Northern Tool + Equipment Co., Inc.
Burnsville, MN 55306
NorthernTool.com
Made in China