Isenberg 160.1168 User manual

InstallationManual
FloorMountTubFiller
www.isenbergfaucets.com
Ver. 2.54
BEFOREYOUBEGIN

•Youmustobservealllocalplumbinglawsandcodes.

•Donotinstallthisitemifitdoesnotmeetlocalplumbingcodes.
•Shutoffthemainwatersupply.

160.1168
160.1167
150.1165
260.1165

www.isenbergfaucets.com
TABLEOFCONTENTS
• OperatingSpecifications . . . . . . . 1
ValveInstallationAndTolerance
 Cut-OutDimensions . . . . . . . 1
RoughInSpecification . . . . . . 2
FaucetPlacement . . . . . . . . 3

SecuringValveToTheFloor . . . . . . . 4
ValvePositionWithRespectToTheTub . . . . . 5
UsingTheWaterPlugs . . . . . . . 5
FlushingTheValve . . . . . . . . 5
InstallingTheTrim . . . . . . . . 6
ReplacingTheCartridge . . . . . . . 8
ReplacingTheDiverterMechanism -160.1168. . . . . 9
ReplacingTheDiverterMechanism -150.1165/160.1167. . . 10
CartridgeMaintenance . . . . . . . 12

•
•
•
•

•
•
•
•
•
•
•
•
NOTICETOHOMEOWNER
• We recommendthatthisproductisinstalledbyaqualified 
professionalplumber.
•Pleasecheckthisproductimmediatelytoensurethatithas
notbeendamagedandiscomplete.Beforeinstallation,please
makesurethisproductisthecorrectmodelandyouhaveall
thepartsrequiredforinstallationanduse.
•Pleaseflushthewatersystemtoensurethatnometalswarf,
solder,andotherimpuritiescanentertheproduct.
•
Turnoffwatersupplybeforecommencingwork. 
•Pleasereadtheseinstructionscarefullyandretainforfuture
reference.
•


WATERTEMPERATURE
ThisvalvemeetsorexceedsANSIA112.18.1andASSE1016
ThisproductiscertifiedbyIAPMO

WATERPRESSURE

Thisproductistobeusedwithawater
pressurerangeof15PSIto80PSIONLY

Ifwaterpressureisgreaterthan80PSI
installapressurereducingvalve(PRV)

Thisproductistobeusedwithwaterat
atemperaturerangeof40˚F-120˚F
ONLY!

www.isenbergfaucets.com
OPERATINGSPECIFICATIONS

CUTOUTDIMENSIONS
Cut Out Dimensions
From Center Point of Valve:
X = 100 mm / 3.93”
Y = 100 mm / 3.93”
X
Y
1
FLOOR CUT-OUT DIMENSIONS
Isenberg’s oor mount valves come with
escutcheon plates to cover the hole in the
tile / oor.
It is essential to review the cut-out
dimensions mentioned here so that the
cut-out in the oor is not accidentally
bigger than the size of the escutcheon
plate.

18mm [0.708”]
Finished Tile
www.isenbergfaucets.com

ROUGHINSPECIFICATION
2
The distance between the center
point of valve inlet (hot, cold) to the
nished tile surface should be
ideally 18mm [0.708”].
Level the valve before securing into
the oor. Ensure valve is straight
and do not install at an angle.
The connections for Hot & Cold
water supply lines are shown on the
left.
HOT
COLD

www.isenbergfaucets.com
FAUCETPLACEMENT
3
min. 6”
min. 3”

www.isenbergfaucets.com
SECURINGVALVETOTHEFLOOR
Markholesforfloorboltinstallation Installvalveusingfloorbolts
Ensurevalveisperfectlylevel
4

www.isenbergfaucets.com
VALVEPOSITIONWITHRESPECTTOTUB
5
Note:
Direction of valve
w.r.t. tub & spout
is shown here.
USINGTHEWATERPLUGS
Thisillustrationhighlightsthe
placementofthevalve.
The supplied plugs should be used to block
water output during installation.
Insert plugs and use connector and screws to
hold in place.

www.isenbergfaucets.com
INSTALLINGTHETRIM-SIZEANDSHAPEMAYVARY-ILLUSTRATIONONLY
Ensuredoubleo-ringsareundamagedandgreased
Inserttrimontovalve.Tightenscrews(x3) Ensurethatallscrewsaretight
6
Installconnectorandtightenscrewsonbottom
oftrim

www.isenbergfaucets.com
INSTALLINGTHETRIM-SIZEANDSHAPEMAYVARY-ILLUSTRATIONONLY
Pushdownfloorcover Screwonhandheldandhose
7

www.isenbergfaucets.com
REPLACINGTHECARTRIDGE
8
Inordertoremoveorservicethecartridgefollowtheprocedurebelow:
1)Removehandle.Coverbuttonandhexscrewonhandlewillneedtoberemoved.
2)Unscrewcartridgebezelandretainingnut.
3)Pulloutcartridge/

www.isenbergfaucets.com
REPLACINGTHEDIVERTERMECHANISM-FOR160.1168
9
1)Removeholderbyremovinghexscrewandpullingout.
2)Removerectangluarknob
3)Removebrassconnectorwitho-ringsbyturning
4)Pulloutdiverter
1
2
3
4

www.isenbergfaucets.com
REPLACINGTHEDIVERTERMECHANISM-150.1165/160.1167
10
Removehandshowerandhose Removeholderbylooseningtwohexscrewsbelow
Removeholderscrews Removewateroutletpiece&knobbytwisting

www.isenbergfaucets.com
REPLACINGTHEDIVERTERMECHANISM-150.1165/160.1167
11
Removepushpullrod

www.isenbergfaucets.com 12
CARTRIDGECLEANING&MAINTENANCE
Check For Dirt
Check For Dirt
Inspect
Rubber
Seal