Isenberg PBV.1005A User manual

InstallationManual-PBV.1005A
1/2”PressureBalanceValveWithIntegrated2-wayDiverter
UseWithTrimsEndingin*2101&*2100
www.isenbergfaucets.com
Ver. 2.53
BEFOREYOUBEGIN

•Youmustobservealllocalplumbinglawsandcodes.

•Donotinstallthisvalveifitdoesnotmeetlocalplumbingcodes.
•Shutoffthemainwatersupply.


www.isenbergfaucets.com
TABLEOFCONTENTS
• OperatingSpecifications . . . . . . . 1
ValveInstallationAndTolerance
 Cut-OutDimensions . . . . . . . 1
RoughInSpecification . . . . . . 2
ConnectingTheSupply&OutputLines . . . . . 3
TrimMarkings/WaterOutput . . . . . . 5
UsingTheSupplyStops . . . . . . . 6
FlushingTheValve . . . . . . . . 6
InstallingTheTrim . . . . . . . . 6
ReplacingTheTemperatureCartridge . . . . . 9
ReplacingTheDiverterCartridge . . . . . . 9
InstallingTheExtensionKit . . . . . . . 10

•
•
•
•

•
•
•
•
•
•
•
NOTICETOHOMEOWNER
• We recommendthatthisproductisinstalledbyaqualified 
professionalplumber.
•Pleasecheckthisproductimmediatelytoensurethatithas
notbeendamagedandiscomplete.Beforeinstallation,please
makesurethisproductisthecorrectmodelandyouhaveall
thepartsrequiredforinstallationanduse.
•Pleaseflushthewatersystemtoensurethatnometalswarf,
solder,andotherimpuritiescanentertheproduct.
•
Turnoffwatersupplybeforecommencingwork. 
•Pleasereadtheseinstructionscarefullyandretainforfuture
reference.


WATERTEMPERATURE
ThisvalvemeetsorexceedsANSIA112.18.1andASSE1016
ThisvalveiscertifiedbyIAPMO

WATERPRESSURE

Thisproductistobeusedwithawater
pressurerangeof15PSIto80PSIONLY

Ifwaterpressureisgreaterthan80PSI
installapressurereducingvalve(PRV)

Thisproductistobeusedwithwaterat
atemperaturerangeof40˚F-120˚F
ONLY!

www.isenbergfaucets.com
OPERATINGSPECIFICATIONS

CUTOUTDIMENSIONS
IsenbergʼsPBV1005Avalvecomeswithapre-at-
tachedmud-guard.Thismud-guardisnottobe
removedordiscarded.Itspurposeistoguidethe
installationprofessionalonthepropercut-out
dimensionsofthedrywall.
Wall Cut Out Dimensions
From Center Point of Valve:
PBV.1005A
X = 138mm / 5.43”
Y = 121mm / 4.76”
1
X
Y

www.isenbergfaucets.com

ROUGHINSPECIFICATION
The distance between back of
the valve to the nished tile
surface should be between
2.44 and 3.14 inches.
Minimum = 62mm [2,44"]
Maximum = 80mm [3,14"]
Finished tile should fall
between Min & Max.
If valve is installed too deep
into the wall, extensions are
available.
2

www.isenbergfaucets.com
CONNECTINGTHESUPPLY&OUTPUTLINES
FixValveonwoodenplank LevelValve
AttachHot/ColdSupplyLines
3

www.isenbergfaucets.com
CONNECTINGTHESUPPLY&OUTPUTLINES
LevelValve AttachHot/ColdSupplyLines
4

www.isenbergfaucets.com
FINISHTILEPOSITION
InstallDrywallandTile.Ensurefinishedtile
surfaceisbetweentheminandmaxmarks
onthemudguards.
Thebelowdiagramshowsthemarkingson
thetrimplateandtheoutputsonthevalve.
Thiswillhelptheinstallationprofessional
toconnecttheappropriateaccessoriestothe
valveoutputports
5
TRIMMARKINGS/WATEROUTPUT
OUTPUT 2
HOT COLD
OUTPUT 1

www.isenbergfaucets.com
USINGTHESUPPLYSTOPS
TurnClock-wise7timestostop
waterflow.
FLUSHINGTHEVALVE
Inordertocleardirtinthelines-
youmustflushthevalvebeforethe
wallisclosedandwateristurnedon
forthefirsttime.
1)Removethe2supplystopsby
turningwithaspanner
2)Removetemperaturecartridge
byturningwithaspanner
3)Removevolumecontrolcartridge
byturningwithaspanner
4)Turnonwatersupplyandlet
waterflowremovinganydirtinthe
lines.
6

www.isenbergfaucets.com
INSTALLINGTHETRIM-TRIMPLATESIZEANDSHAPEMAYVARY-ILLUSTRATIONONLY
Removemudguards Applysiliconebetweenmudguardanddrywall/
tile
Applysiliconebehindtrimplate Pushtrimplatetowardswall
7

www.isenbergfaucets.com
INSTALLINGTHETRIM-TRIMPLATESIZEANDSHAPEMAYVARY-ILLUSTRATIONONLY
8
Insertdiverterhandle Inserttemperaturehandleandtightenhexscrew,
theninsertcoverbutton
Thisphotoshowsacompletelyinstalledtrim

www.isenbergfaucets.com
REPLACINGTHEDIVERTERCARTRIDGE
1.Removedivertercoverbyturning
withhand
2.Removeddiverterholdingnut
withwrench
3.Removedivertercartridge
9
REPLACINGTHETEMPERATURECARTRIDGE
1.Removecartridgecircularbezel
withhand
2.Removedcartridgeretainingnut
withwrench
3.Removetemperaturecartridge

www.isenbergfaucets.com
INSTALLINGEXTENSIONSTOTHEVALVE-OPTIONAL
10
Removedivertertrimpiece InsertDiverterextension
Removetemperaturecartridgeandcartridgecover Inserttemperatureextensionpieceandextended
cartridgecover

www.isenbergfaucets.com
INSTALLINGEXTENSIONSTOTHEVALVE-OPTIONAL
11
Inserttemperaturecartridge,retainingnutand
bezel
Fullyinstalledextensionkitisseenabove