Isenberg TVH.2693 User manual

InstallationManual-TVH.2693
3/4”ThermostaticTubFillerValveWithVolumeControl
UseWithTrimsEndingin*2693
www.isenbergfaucets.com
Ver. 2.53
BEFOREYOUBEGIN

•Youmustobservealllocalplumbinglawsandcodes.

•Donotinstallthisvalveifitdoesnotmeetlocalplumbingcodes.
•Shutoffthemainwatersupply.


www.isenbergfaucets.com
TABLEOFCONTENTS
• OperatingSpecifications . . . . . . . 1
ValveInstallationAndTolerance
 Cut-OutDimensions . . . . . . . 1
RoughInSpecification . . . . . . 2
ConnectingTheSupply&OutputLines . . . . . 3
TrimMarkings/WaterOutput . . . . . . 4
UsingTheSupplyStops . . . . . . . 5
FlushingTheValve . . . . . . . . 5
InstallingTheTrim . . . . . . . . 6
ReplacingTheThermostaticCartridge . . . . . 10
ReplacingVolumeControlCartridge. . . . . . 10
ReplacingSupplyStops . . . . . . . 11
InstallingTheExtensionKit . . . . . . . 12
CartridgeMaintenance . . . . . . . 13

•
•
•
•

•
•
•
•
•
•
•
•
•
NOTICETOHOMEOWNER
• We recommendthatthisproductisinstalledbyaqualified 
professionalplumber.
•Pleasecheckthisproductimmediatelytoensurethatithas
notbeendamagedandiscomplete.Beforeinstallation,please
makesurethisproductisthecorrectmodelandyouhaveall
thepartsrequiredforinstallationanduse.
•Pleaseflushthewatersystemtoensurethatnometalswarf,
solder,andotherimpuritiescanentertheproduct.
•
Turnoffwatersupplybeforecommencingwork. 
•Pleasereadtheseinstructionscarefullyandretainforfuture
reference.


WATERTEMPERATURE
ThisvalvemeetsorexceedsANSIA112.18.1andASSE1016
ThisvalveiscertifiedbyIAPMO

WATERPRESSURE

Thisproductistobeusedwithawater
pressurerangeof15PSIto80PSIONLY

Ifwaterpressureisgreaterthan80PSI
installapressurereducingvalve(PRV)

Thisproductistobeusedwithwaterat
atemperaturerangeof40˚F-120˚F
ONLY!

www.isenbergfaucets.com
OPERATINGSPECIFICATIONS

CUTOUTDIMENSIONS
IsenbergʼsTVHSeriesvalvescomeswithablack
pre-attachedmud-guard.Thismud-guardisnot
toberemovedordiscarded.Itspurposeisto
guidetheinstallationprofessionalontheproper
cut-outdimensionsofthedrywall.
X
Y
Wall Cut Out Dimensions
From Center Point of Valve:
TVH.2693
X = 53mm / 2.08”
Y = 205mm / 8.07”
X
Y
1
X
Y

www.isenbergfaucets.com

ROUGHINSPECIFICATION
The distance between back of
the valve to the nished tile
surface should be between
2.71” and 3.46” inches.
Minimum = 61mm [2,40"]
Maximum = 93mm [3,67"]
Finished tile should fall
between Min & Max.
If valve is installed too deep
into the wall, extensions are
available.
2

www.isenbergfaucets.com
CONNECTINGTHESUPPLY&OUTPUTLINES
FixValveonwoodenplank LevelValve
AttachHot/ColdSupplyLines
3

www.isenbergfaucets.com
FINISHTILEPOSITION
InstallDrywallandTile.Ensurefinishedtile
surfaceisbetweentheminandmaxmarks
onthemudguards.
Thebelowdiagramshowsthemarkingson
thetrimplateandtheoutputsonthevalve.
Thiswillhelptheinstallationprofessional
toconnecttheappropriateaccessoriestothe
valveoutputports
4
TRIMMARKINGS/WATEROUTPUT
OUTPUT
HOT COLD

www.isenbergfaucets.com
USINGTHESUPPLYSTOPS
TurnClock-wise7timestostop
waterflow.
FLUSHINGTHEVALVE
Inordertocleardirtinthelines-
youmustflushthevalvebeforethe
wallisclosedandwateristurnedon
forthefirsttime.
1)Removethe2supplystopsby
turningwithaspanner
2)Removethermostaticcartridge
byturningwithaspanner
3)Removevolumecontrolcartridge
byturningwithaspanner
4)Turnonwatersupplyandlet
waterflowremovinganydirtinthe
lines.
5

www.isenbergfaucets.com
INSTALLINGTHETRIM-TRIMPLATESIZEANDSHAPEMAYVARY-ILLUSTRATIONONLY
Removemudguards Install42mmring
Ahardpushmayberequired The42mmringmustbeflush.Otherwisethehandle
willnotfitproperly
6

www.isenbergfaucets.com
INSTALLINGTHETRIM-TRIMPLATESIZEANDSHAPEMAYVARY-ILLUSTRATIONONLY
Inserttrimplate AlignTrimplatetillitisstraight
Insertadapterbaseandtighten Insertcenteringknob&screws
7

www.isenbergfaucets.com
INSTALLINGTHETRIM-TRIMPLATESIZEANDSHAPEMAYVARY-ILLUSTRATIONONLY
Insertvolumehandle.Tightenhexscrew&insert
coverbutton
Removeanti-scaldtemperatureringandreinsert
incorrectposition-seenextimage
Caliberatecartridgebeforeinsertingtemperature
handle.Redmarksmustalign.
Correctlyre-insertanti-scaldtemperatureringinthe
rightposition
8

www.isenbergfaucets.com
INSTALLINGTHETRIM-TRIMPLATESIZEANDSHAPEMAYVARY-ILLUSTRATIONONLY
Inserttemperaturehandle.Tightenhexscrew&
insertcoverbutton
9
Thisphotoshowsacompletelyinstalledtrim

REPLACINGTHEVOLUMECARTRIDGE
www.isenbergfaucets.com
REPLACINGTHETHERMOSTATICCARTRIDGE
1.RemoveAnti-ScaldRing
2.Thetemperaturecartridgecanbe
removedeasilyinoneoperationby
usingaspanner.
1.RemoveThreadedRodusingaspanner
2.Removediverterflange
3.Removecartridgebyturningwithaspan-
nerandpullingoutwithapairofpliers.
10

www.isenbergfaucets.com
REPLACINGTHESUPPLYSTOPS
11
Useaspannertotwistintheshownpositionand
removesupplystop

www.isenbergfaucets.com
INSTALLINGEXTENSIONSTOTHEVALVE-OPTIONAL
Installvolumeextensionkit-3Piecesasshown
above
Removeantiscaldtemperaturering
12
Installthermostatichandleextensionandreinsert
antiscaldtemperaturering
CompleteExtensionAssembly

Clean Filters
Check For Dirt
www.isenbergfaucets.com
CARTRIDGECLEANING&MAINTENANCE
13
Thermostatic Cartridge:
Inspect O-rings
Volume Control Cartridge:
Check For Dirt