Iseo Zero1 stylos 2 User manual

Stylos 2

ELECTRONIC SUPPORT SERVICE

iseozero1.com

iseo.com

Iseo Serrature s.p.a

Via San Girolamo 13

25055 Pisogne (BS)

ITALY

Tel. +39 0364 8821

[email protected]

Non contractual document. Subject to change. Cod. 60000STY2LV01.4 - 08/06/2020

INSTALLATION GUIDE (EN)

WARNINGS

Read this manual prior to use the device in order to ensure a safe and proper use.

Preserve this manual as future reference.

The installation and maintanance of the device must be carried out by qualified technical staff, adequately

trained by ISEO.

The instructions should be carefully followed during installation. These instructions and any maintenance

instructions should be passed on by the installer to the user.

No modifications of any kind are permitted, except for those described in these instructions.

The product must be destined only for the use for which it is expressly designed and therefore as a

credential reader for civil and industrial locations. Any other use is considered improper and dangerous.

The electrical connection must be made according to the constructor's instructions and respecting the

regulations in force.

Disconnect the power supply before carrying out any technical service that involves opening or accessing

the internal parts of the product.

In the event of a failure and/or poor operation, remove the power supply using the main switch and do not

tamper with it. For all repairs, exclusively contact a technical assistance center authorized by the constructor.

4. READER/VALIDATOR SETTING

For more information about Stylos and Atlas, refer to

the Atlas Installation Manual available at:

app.iseo.com.

Back side view

Circuit board

J2.

JPS

Stylos as Reader/Validator = Address 1

LEGEND:

J2.1/2/3/4 = Power supply/Lockbus

JPS = System Jumper (reserved)

S1 = Programming button

JP 0/2/4/6 = Bus Address Jumpers

Back side view

Circuit board

J2.

JPS

ADDRESS 0 =

ADDRESS 2 =

ADDRESS 4 =

ADDRESS 6 =

BUS

ADDRESS

(Master)

(slave)

FUNCTION

(Communication Channel)

NEGATIVE (-) GND

POSITIVE (+) Power Supply

LOCKBUS

}

BUS

ADDRESS

J2.

JPS

3.1 STAND-ALONE GATE ELECTRICAL CONNECTIONS

mm²0.20÷1.5

Minimum/maximum cross-section

of the cables is:

(24÷15AWG).

Power supply: 8÷30 VDC 3W MAX

3. STAND-ALONE GATE SETTING

Back side view

Circuit board

Only to set the Stylos 2 to be used as Stand-Alone

gate, you have to close, by a jumper, PIN 2 and 3 as

shown in the picture.

Fit the jumper when

the Stylos is OFF.

J2.

JPS

Stylos as Stand-Alone gate = Address 0 (Master)

2. DISASSEMBLING

Disconnect the power before opening the device.

1. VERSIONS AND DIMENSIONS

A = 47,5mm

B = 17,5mm

C = 130mm

A = 40mm

B = 10mm

C = 125mm

Credential reader

with led Spacer for wall

installation

This guide includes instruction

to configure the Stylos as

Stand-Alone gate or as

Reader/Validator, connected

to Atlas. Refer to the proper

section.

TECHNICAL DATA

Power Supply:

8÷30 VDC 3W MAX

Operating temperature: -20°C + 60°C

RFID: frequency 13,553 - 13,567 MHz, maximum magnetic field: 0,89 µA/m (measured at 10m at the

maximum power capacity).

Only for devices with on-board Bluetooth radio: frequecy 2,40 - 2,4835 GHz, maximum power: 5,25 mW.

Lithium Battery

CR2032 - 3V

CR2032

Lithium

Risk of explosion if the battery is replaced with an incorrect type.

Dispose of batteries according to your local environmental laws and guidelines.

Battery replacement must be carried out by qualified technical staff.

For the replacement battery procedure, read the user manual available at app.iseo.com.

EC Declarations of conformity available at:

https://www.iseo.com/it/en/download

9.1 INSTALLATION WITH THE SPACER

Check the connections

on section 5 or 6

before powering the

device.

Take care to not

damage the cables

while installing the

device.

9. INSTALLATION WITHOUT THE SPACER

Check the connections

on section 5 or 6

before powering the

device.

Take care to not

damage the cables

while installing the

device.

5 x 25 mm

3.9 x 30 mm

Ø 5 mm

Ø 26 mm

Ø 5 mm

8. INSTALLATION ON A WALL

7. INSTALLATION ON A METAL PROFILE

Ø 3.2 mm

(max)

Ø 3.2 mm

(max)

Ø 26 mm

3.9 x 19 mm

6.1 STAND-ALONE GATE: EXCHANGE OF CODED KEYS WITH ACTUATOR

(EXCHANGE KEYS)

J2.

JPS

Back side view

Power supply

24VDC 25W

COM

NO/NC

GND

IN AN

I/O 2

I/O 1

VCC

GND

L2L1P1 P2 LRL

J P 3

LPW

J P 2L C HJ P 1LV O

V2 Output

V1 Output

OPEN

V PWR +

GND

EARTH

For more information regarding the exchange of keys, see the Tutorial Video available at

app.iseo.com.

Switch on the Stylos keeping

pressed the button and wait

for the acustic and light signal,

then release it immediately.

Switch on the actua-

tor keeping pressed

one button for 3 sec.

Stylos Master

address 0

Actuator

address 1

6. STAND-ALONE GATE: EXCHANGE OF CODED KEYS WITH ACTUATOR

(JUMPER SETTING)

J2.

JPS

Back side view

Power supply

24VDC 25W

COM

NO/NC

GND

IN AN

I/O 2

I/O 1

VCC

GND

L2L1P1 P2 LRL

J P 3

LPW

J P 2L C HJ P 1

L V O

V2 Output

V1 Output

OPEN

V PWR +

GND

EARTH

Stylos Master

address 0

Set jumpers on Actuator and Stylos as per pictures below. Note this configuration is correct only

in case of 1 Stylos (Master) and 1 Actuator (Slave).

For more information about

jumper setting with different

configuration, refer to the

Stylos User Manual available

at app.iseo.com.

Actuator

address 1

5. ACTUATOR CONFIGURATION: LOCKBUS SELECTION

Switch on the Actuator and check if red led

flashes:

2 times (Lockbus 2) = Stand-Alone gate.

Change the Lockbus type accordingly to your

configuration, following the next point.

Switch on the Actuator keeping pressed both

buttons simultaneously for 1 sec.

Switch on it again to check if now red led

flashes 1 or 2 times.

If not repeat the procedure.

Power supply

24VDC 25W

COM

NO/NC

GND

IN AN

I/O 2

I/O 1

VCC

GND

L2L1P1 P2 LRL

J P 3

LPW

J P 2L C HJ P 1L V O

V2 Output

V1 Output

OPEN

V PWR +

GND

EARTH

Red led flashing

JP 1

Back side view

Circuit board

J2.

1.2.3

JP2

ADDRESS 5 =

ADDRESS 6 =

ADDRESS 7 =

ADDRESS 8 =

ADDRESS 1 =

ADDRESS 2 =

ADDRESS 3 =

ADDRESS 4 =

BUS

ADDRESS

(Communication Channel)

NEGATIVE (-) GND

POSITIVE (+) Power Supply

LOCKBUS

}

BUS

ADDRESS

JP 1

J2.

1.2.3

JP2

JP 1

4.1 READER/VALIDATOR ELECTRICAL CONNECTIONS

mm²0.20÷1.5

Minimum/maximum cross-section

of the cables is:

(24÷15AWG).

Power supply: 8÷30 VDC 3W MAX

Iseo Zero1 Stylos 2 User manual

Popular Ebook Reader manuals by other brands