ISO Preferred BA203 User manual

ISO PREFERRED, 1419 DONELSON PIKE, SUITE A, NASHVILLE, TN 37217
ISOPREFERRED.COM
jljlkjljljlk
.
ISO Preferred Lumbar Back Brace III (BA203) has a heat moldable posterior panel. It is intended to provide support for the
sacrococcygeal junction to the T9 vertebra and supports conditions such as mild disc herniation of the lumbar, strain or sprain of the
lower back, Spondylosis, Spondylolisthesis and Lumbago.
Lumbar Back Brace III
The ISO Preferred Lumbar Back Brace III reduces the time it takes to heal discomfort from
injuries or post-surgery. Please follow your orthopedic professional’s instructions explicitly
and adjust or discontinue use only as directed to achieve maximum benefit for your
concerns.
Always Putting Our Patients First
1. The belt is designed to fit waist sizes Small to 2XL. To apply, lay out the back brace on a
flat surface. Ensure the pull tabs are nearest to the middle of the back of the brace
without the cords bunching up.
2. Position the center of the lumbar back brace over your spinal region at your desired
height. Pull firmly and equally on both sides of the support belt, wrapping and
overlapping them in front of your stomach. Then secure together with fastening fabric.
 If the belt is too long or too short, turn belt to inside.
 Unfasten the belt overlap at position “A”.
 Adjust the length on each side.
 Adjust both belts equally to position front and back
plates properly. Excess belt may be cut as desired.
 Proceed to apply and fasten the belt as instructed above.
3. Detach both pull tabs (attached to the cords) from the support belt. While pulling
slowly towards the front towards the front of your stomach, firmly and evenly increase
the compression support to your doctor’s prescribed specific level. Re-attach both pull
tabs. DO NOT OVERTIGHTEN.
A pocket on the inside of the lumbar back plate will allow you to add a hot or cold pack
to aid in relieving any muscle discomfort.
ISO Lumbar Belt Extension: Universal (Optional- BA202)
For additional length at the waist securely fasten the (optional) ISO Lumbar Belt
Extension: Universal to each side of the ISO Lumbar Belt.
3
2
2
1
A
A

ISO PREFERRED, 1419 DONELSON PIKE, SUITE A, NASHVILLE, TN 37217
ISOPREFERRED.COM
INTRODUCTION
Your ISO Preferred Lumbar Back Brace III (BA203) is designed to provide your body with the support and stability
that it needs to successfully manage or eliminate your mobility concerns. It is critical that you follow your
orthopedic professional’s directions closely to ensure that the apparatus is worn properly and in the manner that
will be most beneficial in addressing your issues. For correct application, please read the enclosed instructions and
watch the on-line instructional video at www.ISOpreferred.com so that this device can provide you with superior
long-term usability and care.
USAGE RECOMMENDATIONS
It is vital that you read the included instructions and when applicable watch the instructional video for the ISO
Preferred Lumbar Back Brace III (BA203) that is included here within. It is intended for the use of qualified
professionals only. It is not recommended for patients to fit or apply or adjust their new brace without an
orthopedic professional’s expertise, unless otherwise instructed. Further questions in regards to adjustments or
changes, frequency of use, and/or duration of use should be presented to your orthopedic professional, as they are
familiar with your needs and conditions, for which this device was prescribed.
CARE AND CLEANING INSTRUCTIONS
Please do not place your brace in the washing machine or dryer at any time. When preparing to clean your ISO
Preferred Lumbar Back Brace III (BA203) you will want to separate the parts where applicable and care for them
individually.
 Do not dry clean, iron, bleach, or use an abrasive cleaning instrument on any part of the brace. Failure
to follow these instructions may damage your brace and void the manufacturer's warranty and it may
no longer work properly.
 Hand wash each section in cold water with a mild detergent. Lay flat to air dry.
 Allow all parts to air dry prior to reassembling the device.
CAUTION
The ISO Preferred Lumbar Back Brace III (BA203) is for single patient use only. While every effort has been made to
obtain maximum strength, function and durability, there is no guarantee that injury will be prevented through the
use of this device, especially if the instructions are not followed correctly. DO NOT OVERTIGHTEN.
Always Putting Our Patients First