iTime TB1-T User manual

Smart Intelligent Temperature Detection Bracelet
User Manual

1，Adapt platform requirements：
Android 4.2 IOS 8.0 or above BT 4.0
2，Before using
Please make sure the bracelet has enough power
for the first time, if the power cannot be started,
please charge the bracelet first.

3，“Lefun Health”APP download
1. Scan the QR code to download
2. Search “Lefun Health”app from App store
or Android market to download.

4，Match the bracelet with phone
Long press the touch button to turn on, please
make sure that the bluetooth of the mobile
phone is enabled. Open the mobile APP- click
the function bar in the upper left corner - click
the APP icon - click "search" - select the MAC
string code that matches the bracelet to show
"bluetooth request pairing" and click "pair and
connect";
5，Operation
Long press for 6 seconds to power on and the
bracelet is connected.
Synchronize time and date of the phone;
The APP can synchronize the movement status
of the bracelet, such as “Sleeping, heart rate,
blood pressure and other data”

Long press the ‘power off’button to turn off.
6，Function
Home: dial can be switched, display time, date,
power;
Measuring Temperature:
Wear it on the wrist and adjust it close to the wrist. In order to measure
the temperature accurately, it is recommended to measure the temperature
after wearing it for about 10 minutes and test it for about 3 minutes, which
will show the body surface temperature and body temperature.

Step-counting:
Count the steps for the whole day, clear it at
00:00am every day, you can check the historical
steps in the APP;
Sport Mode:
Record the duration of exercise, clear it at
00:00am every day, you can check the historical
steps in the APP;
Measuring Oxygen:
When the function is switched to the blood
oxygen interface, the measurement will
automatically start.
The result is transferred to the APP for saving;
Measuring Heart rate:
When the function is switched to the heart rate
interface, the measurement will automatically
start.

The result is transferred to the APP for saving;
Sleeping Monitoring:
Record the duration of your sleeping, clear it at
00:00am every day, you can check the historical
steps in the APP;
Measuring Blood Pressure:
When the function is switched to the heart rate
interface, the measurement will automatically
start.
The result is transferred to the APP for saving;
Smart Alarm:
Set the alarm on the app, the bracelet will vibrate
when it is time.
Sedentary Reminder:
Open the ‘sedentary reminder’ from the
"bracelet function Settings"in the app, Switch,
set duration, etc., the bracelet will vibrate when it

is time;
Messages Reminder:
After the bracelet and APP match successfully,
the mobile phone receives the WhatsApp,
WeChat, SMS and other application messages,
the bracelet will be brighten the screen and
vibrate.
Incoming Call Reminder:
After the bracelet is paired with the APP, when
there is incoming call, it will display the contacts
information;
Shake to Take Photos:
Open this function in the APP "bracelet function
Settings". After that, click "shake to take photos"
function to enter the interface;
Find Bracelet:
Click "find bracelet" function, and the bracelet
will vibrate.

Factory Reset:
Set the time to the previous day or the forward
day in the mobile APP to synchronize then can
clear the bracelet data.
Basic Specification
Type
Smart bracelet
battery
Li-polymer
Vibrating motor
Support
synchronization
method
Bluetooth 4.0
Working temperature
-10℃~50℃
sensor
Low power
accelerometer
System requirement
IOS 8.0 above/Android 4.2 above
Notice:
1. Don't wear them for bathing or swimming.
2. Please connect the bracelet when synchronizing data.
3. Do not expose the band to high moisture,extremely
high/low temperature for long periods of time.

4. If the bracelet dies and restarts. Please check the
phone's memory information to clear and try again, or
return the APP and open it again.
Parts Introduction
*We reserve the right to modify the instruction
without notice.

NOTE: This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are
designed to provide reasonable protection
against harmful interference in a
residential installation. This equipment
generates uses and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this
equipment does cause harmful interference to
radio or television reception, which

can be determined by turning the equipment off
and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the
equipment and receiver.
-Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV
technician for help
Changes or modifications not expressly
approved by the party responsible for
compliance
could void the user's authority to operate the
equipment.

This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful
interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.