Itouchless AV002A User manual

Auto Cleaner With Remote Controller
INTELLIGENT CLEANER
OPERATING MANUAL
AV002A

- 1 -
INTELLIGENT CLEANER
OPERATING MANUAL
Dear customers,
Thank you for using our Intelligent Vacuum Cleaner!
The Intelligent Cleaner is our creation and manufactured by using our own mechanical
electronic technology. It can be used widely in your family, office and entertainment
places. Also it is hard to clean area where workers cannot easily access.With the help
of this intelligent Cleaner, the quality of your life is enriched.
The Cleaner is only recommended for indoor use. It can be used to clean floor
surfaces including hardwood, linoleum, tile and low pile carpets. If you want your
hardwood or tile floor brighter, clean the brush after it cleans the floor, and then
scoop up some liquid wax with the spoon and start the Cleaner again. The fashion flat
design facilitates its cleaning under the sofa, table, and bed, etc. Its convenient
remote control function enables a hands-free operation.

- 2 -
INTELLIGENT CLEANER
OPERATING MANUAL
When you unpack the box, the Intelligent Cleaner
will be included with the following attachments:
1. Battery Charger X 1
2. Rechargeable Battery Pack (Installed) X 1
3. Spoon X 1
4. Filter Mesh X 1
5. Remote Controller X 1
6. Side Brush X 1
7. Dust Brush X 1
8. Operating Manual X 1
Intelligent Cleaner Rechargeable Battery Pack
Spoon
Side Brush
Remote Controller
Charger
Dust Brush
Filter Mesh

Easy to grab handle
Removable particle bin
Start button
Battery life indicator
- 3 -
INTELLIGENT CLEANER
OPERATING MANUAL
Intelligent Cleaner is installed with:
Rechargeable battery
Battery charger socket
Side brush
Power switch
Main brush
Filter
Vacuum inlet lid
Sensors
Sensors
Surface
Bottom
Infrared sensor
***When unit is operating, the side with sensor should move forward.

- 4 -
INTELLIGENT CLEANER
OPERATING MANUAL
After the introduction of the Intelligent Cleaner,
please note the following operating procedures:
The Cleaner can make repeated screw type cleaning within the
scope of 3 feet of diameter, focusing to clean a spot for 4 minutes. It’s
applicable for cleaning the room where it is dirty at partial places.
The Cleaner will automatically clean the room for 30 minutes. The
mode is applicable for cleaning a small room.
The Cleaner won’t stop running until complete consumption of is the
complete consumption of its power. The maximum working is
60 minutes.
When wrong start button is pressed, the other start switch needs to be pressed
twice before cleaning.
4.
5. The max working time for the Cleaner is about 45-60 minutes, which can meet the
requirements for cleaning a normal room. If the battery power is about to run out, the
battery life indicator will become red, and it will stop working. Charging of battery is
needed.
Please ensure the battery is fully charged before starting the Cleaner.
Please tidy unfixed articles on the floor before using the Cleaner, and keep it from the
edge of the carpet and power lines, etc.
Turn on its main power start button, there are three start buttons: Spot, Clean and
Max, representing three different cleaning modes.
1.
2.
3.
A. Spot mode
B. Clean mode
C. Max mode

INTELLIGENT CLEANER
OPERATING MANUAL
Firstly confirm whether the using voltage of charge confirms to the local one for
unconformity will result in damages of charge and unit.
The power indicator on the panel will keep flashing during charging,and turn solid
green from flashing green upon fully charging. then the charging should be stopped
in case of damaging charger. Generally, the charging time is about 4-5 hours.
The charger should be stored in a dry and well-ventilated area, and can’t be used
in wet environments such as a bathroom, etc. in case of any dangers.
It’s strictly forbidden to throw the charger or directly pull out the power line with
hand for inserting or pulling out the charger.
In order to prolong the service life of the battery, it should be charged for 8-9 hours
for the first use or when being used again after a long time. It only can reach its best
performance after 2-3 circles for charging and discharging.
Note on charging:
- 5 -
Outlet
Battery charger socket
a.
b.
c.
d.
e.

INTELLIGENT CLEANER
OPERATING MANUAL
Use the infrared remote controller by refer-
ring to the following drawing:
- 6-
Power key
Direction key
Max key
Clean key
Spot key
Indicator
The cleaner can be controlled to clean by the infrared remote controller. As shown in
the above drawing,the three keys: Spot, Clean and Max work respectively for the
three work modes. Using the direction keys, it can control the cleaners’ movement.
The P key is for powering on/off. If you press the P key, the indicator light on the unit
will turn off, and the Cleaner will enter Sleep mode, which will save energy while in
its non-operating state. If you press the P key again, indicator light on the unit will turn
on, and the Cleaner will enter the Standby mode, while waiting for the next command.
The Intelligent cleaner is user-friendly with very little maintenance required after use.To
ensure optimal performance please observe the following procedures:

- 7 -
INTELLIGENT CLEANER
OPERATING MANUAL
1. Empty the bin
2. Clean the filter mesh
Empty the removable particle bin by following two pro-
cedures below:
Press the clip slightly and put the bin back to the Cleaner.
c. Clear the dirt on the filter mesh.
d. Fit the filter mesh back to the bin.
a. Turn off the power switch.
b. Press down the bin clip and pull out the bin as shown in the following
illustrations below:
c. Clear the bin.
d. Press down the clip on the bin to insert the bin back to the unit.
a. Turn the bin upside down.
b. Press the bottom slightly, take the filter mesh out as shown in the
following illustration:

Turn off the power switch and put the Cleaner on a flat surface with its bottom side up.
Use cross head screwdriver to remove the fixing screw on the right, and then take
out the main brush, rubber brush and brush coupler together as shown in the
following drawing.
- 8 -
Brush coupler.
INTELLIGENT CLEANER
OPERATING MANUAL
Clean the chamber where the brush is located and the contaminants on brush and
rubber brush.
Wipe out dirt on the metal shaft and bearing of the brush coupler and the brushes
(this may not be necessary to do after every cleaning) as per the following drawings.
If necessary, you may add a little lubricant to it.
5.Put the brush coupler and brushes back and tighten the screw.
1.
Clean the main brushes of the Cleaner
2.
3.
4.

- 9 -
INTELLIGENT CLEANER
OPERATING MANUAL
1. Turn off the power switch; turn the Cleaner upside down on a flat surface.
2. Take the Vacuum Inlet Lid out as per following drawing:
3. Clean the Vacuum Inlet Lid and the fan-shaped mechanism to ensure good
ventilation.
4 .Guide the hinge tabs on the Vacuum Inlet Lid back into their holes carefully.
Method for replacement of side brush
Bottom
Fig. 1 Fig. 2
1. Remove the two screws as per the Fig.1.
2. Turn the side brush to the extent that the screwdriver can be inserted as per the
Fig.2, loosen the screw, take off the old brush and replace with new one.
3. Install the side brush and bottom housing in reverse order.
The side brush is consumable. See the following picture for the replacement method.
Clean the vacuum inlet lid

- 10 -
INTELLIGENT CLEANER
OPERATING MANUAL
Intelligent path judgment
Please remove small objects such as a vase, small paper box etc,
which can be knocked down by cleaning. Please must clear these
items first before the Cleaner can carry out its work.
It is switched on but stops after the short music plays. Then this may mean the
battery is low or off and charging is needed.
Please do not use the Cleaner on medium and high-pile carpets.
Avoid using the Cleaner where there are objects such as clothing, power cords,
towels, etc. These things may entangle the brushes of the Cleaner.
Turn off the power when not in use, and make sure the unit is fully charged if it
has not been used for a long period of time. Take battery out of the unit and store
the battery and unit in a cooler place when it’s not being used. Keep the bottom of
the cleaner dry and clean
The Intelligent Cleaner is a vacuum cleaning device which
can control dust, making it a wonderful cleaning assistant.
Attention should be paid to the following points:
Caution
1.
2.
3.
4.
The cleaner is intelligently controlled so that it operates powerfully to avoid any
obstruction and also from falling down from the edge of the table, staircase or
pathway.

What should we do if the Cleaner is dropped down from the edge of stairs?
Solution: Wipe away the dust for the probe at the bottom of the front plate with a dry
cloth.
1.
2.
3.
Troubleshooting:
The cleaner and light turn on, however, no movement
- Make sure no obstacles in pathway
- Check if carpet is under 1 inch
- Clean off debris from brushes
- Clean out trash compartment
- Clean sensors with a damp and dry cloth
- Try all 3 modes
- Charge overnight
Will run for a few minutes, then turn off
- Check for any obstacles in the way
- Try to run mode 3
- Charge overnight
No light, no response
- Check if unit is flashing green while charging
- Charge overnight
Cannot charge battery
- Make sure battery installed correctly
- Check the connection
Will not run from one surface to another
- Check if carpet is under 1 in
- Make sure no obstacles in pathway
- Remove sidebrush and try again
Cleaner stays in one place and rotates
- Make sure no obstacles in pathway
- Clean off brushes
4.
5.
6.
7.

Other manuals for AV002A
1
Table of contents