If you would like to quick hook-up the power
inverter and check its performance before
going ahead with your installation, please
follow these guidelines:
1.
Unpack and inspect the power inverter,
check to see that the power switch is in the
OFF position.
2.
Connect the cables to the power input
terminals on the rear panel of power inverter.
The red terminal is positive (+) and black
terminal is negative (-).
Connect the cables into the terminals and
tighten the wing nut to clamp the wires
securely.
3.
Connect the cable from the negative terminal
of the inverter to the negative terminal of
the power source. Make a secure connection.
Loosely tightened connectors result in
excessive drop and may cause overheated
wires and melted insulation.
4.
Before proceed further, carefully check that
cable you have just connected connects
from the negative terminal of inverter to the
negative output terminal of the power source.
Reverse polarity connection will blow
a fuse in inverter and may permanently
damage the inverter. Damage caused
by reverse polarity connection is not
covered by our warranty.
5.
Connect the cable from the positive terminal
of inverter to the positive terminal of the
power source. Make secure connection.
You may observe a spark when you make
this connection since current may flow to
charge capacitors in the power inverter.
Do not make this connection in the presence
of flammable fumes, explosions or fire
may result.
6. Set the power switch to the ON position.
Check the meters and indicators on the
front panel of the inverter.
300W
Sine Wave
DC to AC Power inverter manual
HT-S-300
If does not, check your power source and
the connections to inverter. The other
indicators should be off.
7.
Set power inverter switch to the OFF
position, the indicator lights may blink.
Plug the test load into the AC receptacle
on the front panel of the inverter. Please
keep switch in off position.
8.
Set power inverter switch to the ON
position, the inverter should supply
power to the load.
1. Where to install
The power inverter should be installed in a
location that meets the following requirements:
a.
Dry - Do not allow water to drip or splash
on the inverter.
b.
Cool - Ambient air temperature should
be between 0℃and 40℃, the cooler the
better.
c. V
entilated - Allow at least one inch of
clearance around the inverter for airflow.
Ensure the ventilation openings on the
rear and bottom of the unit are not
obstructed.
d.
Safe - Do not install the inverter in the
same compartment as batteries or in any
compartment capable of storing flammable
liquids such as gasoline.
2. Cables
DC to AC inverters require high amperage/low
voltage DC power to low amperage/high
voltage AC power. To operate properly
connect inverter DC input terminals direct
to battery with heaviest wire available see
chart below:
Approx. Amps
Req'd Wire Guage
Max Watts Out
15A #16150W
30A #12300W
60A600W
100A #4
#4
#4
2 X #4
2 X #4
1000W
120A1200W
150A
#6 or 2×#10
1500W
1800W
2500W
180A
250A
Firstly, thank you for purchase our product.
Please read this manual carefully before
installing or using this product.
This model is used in a wide range of
application including remote homes, RVs,
sailboats and powerboats.
It will operate most televisions and VCR,
personal computers, small appliances
and tools such as drills, sanders, grinders,
mixers and blenders.To get the most out
of the power inverter, it must be installed
and used properly. Please read the instructions
in this manual before installing and using
this model.
Introduction
Quick hook – up and testing
Installation
◎
Pure sine wave output (<2% THD).
◎
Input & Output fully isolation design.
◎
High surge in motor start capacity.
◎
5-stage thermal control fan.
◎
Frequency 50/60HZ switchable.
◎
Auto restart.
◎
Small size.
MODEL: HT-S-300
SPECIFICATIONS
HT-S-300-12 HT-S-300-24 HT-S-300-48
Model No.
Continuous Output
Power
Max Output Power
DC Input Voltage
AC Output Voltage
Frequency
No Load current
Draw
Output Wave form
Input Low
Voltage Alarm
Input Low Voltage
Protection
Overload Protection
Temperature Protection
Output Short Circuit
Protection
Efficiency
Input Reverse Pola
rity circuit protection
Distortion
Dimensions
(L x W x H / mm)
Net Weight (by Kg/s)
100VAC
120VAC
230VAC
300W
600W
DC24V DC48VDC12V
50Hz / 60Hz±3%
(Switch selectable)
0.3A 0.2A0.6A
Pure Sine Wave
YES
>87%
YES
<2%
YES
YES
(
55°C±5°C
)
YES
260 x 129 x 82.5
2.0
POWER LED
ON/OFF
SWITCH
60HZ
AC OUTPUT
50HZ
Rear view
Fan
DC Input 50/60HZ
Switch selectable
EARTH
Fan
+
-
DC Input
