J.Burrows ASHFORD JBASHFMBBK User manual

Weight capacity: 120kgs
1 CTN
This design and instruction booklet is subject to copyright.
www.officeworks.com.au
For spare parts or hardware call [phone] or email [email protected]
ASSEMBLY INSTRUCTIONS
ASHFORD MEDIUM BACK MESH CHAIR
JBASHFMBBK

[phone]
20min
•Please check you have all hardware before assembly.
•If you are missing any hardware, please contact Kyvas on [phone] or
email [email protected]
•Please ensure you have the name of the item, required hardware part and quantity.
•Please retain your receipt as proof of purchase to validate your warranty.
NOTE
• Do not tighten screws before all screws are in the right place.
• Do not use this product unless all bolts, screws and knobs are firmly secured.
• Check that all bolts, screws and knobs are securely tightened at least every 4 months.
CAUTION
• If parts are missing, broken, damaged or worn stop using the product until all repairs
are made using manufacturer authorised parts.
• Failure to follow these warnings could result in serious injury.
WARNING
• CHILDREN MUST BE SUPERVISED.
Officeworks Ltd. | 236-262 East Boundary Road | Bentleigh East VIC 3165 | AUSTRALIA
DANGER
2/10

3/10
H
x1 x1
x5x1 x1 x1
x1 x2
C
LR
x 1
M6
J
x 4x 2
I
6x20mm
K
x 6
6x30mm
LM
x 6
6x40mm

Note: Push the castors (H) firmly into hole at the end of each leg.
Note: Turn the Star Base (G) upright and insert Gas Lift (E) into the center hole of Star Base (G).
Place cover (F) over the Gas Lift (E).
F
E
H
G
G
4/10

Note: Attached Armrests (C) to the Seat Cushion (B) using 6xScrews (J) with Allen Key (L).
Do not tighten Screws fully until you have completed assembly.
Note: Attach Backrest (A) to the Seat Cushion (B) using 4xScrews (K) with Allen Key (L).
Fully tighten the screws with Allen Key (L).
J
L
L
K
A
C-L
B
B
60%
5/10
J
6Pcs
ø6x30mm
used to complete
this step.
K
4 Pcs
used to complete
this step.
ø6x40mm
FRONT
FRONT

Note: Attached Armrests (C) to the Backrest (A) using 2xScrews (K) .
Fully tighten the screws with Allen Key (L).
Note: Align the Seat Plate (D) so the FRONT of the Seat Plate matches the FRONT
label on the bottom of the Seat Cushion (B) . Fully tighten the screws with Allen Key (L).
L
K
B
D
A
C-L
L
I
100%
6/10
6
K
2 Pcs
used to complete
this step.
ø6x40mm
FRONT
I
4 Pcs
ø6X20mm
used to complete
this step.
FRONT

M
M
E
Your Ashford Medium Back Mesh Chair is now complete and ready for use.
IMPORTANT NOTE: Periodically check and re-tighten screws.
8
Note: Place assembled seat on the Gas Lift (E). Push down firmly until connection is secure.
7
7/10

Thank you for your purchase. Please retain your receipt to validate warranty.
If you would like to know more about our furniture products, please visit www.officeworks.com.au
8/10
• Spot clean mesh/fabric with upholstery shampoo or dry cleaning powder only.
• Do not saturate mesh/fabric. Apply proprietary cleaning products strictly according
to instructions. Wipe dry immediately with an absorbent dry cloth.
• Treat spills on PU material immediately with an absorbent cloth by blotting the spill.
• Do not use detergents, solvents or abrasive cleaners.
Care Instructions
• Keep away and protect from direct sunlight and heat.
• Avoid contact with skin, in particular during high temperatures and humidity.
• Clean, check and tighten all parts regularly.
• Vacuum regularly.

Ashford Medium Back Mesh
Chair Functionality
Chair Tilt
- To increase chair height pull
lever upward while lifting body
weight slightly off the seat.
- Release lever at desired height.
- To lower chair height sit fully into
the chair and pull lever upward.
- Release lever at desired height.
Your feet should be resting flat on
the floor.
Adjustable Tilt Tension Control
- Turn continuously to adjust how
quickly chair tilts back & forth.
Note: if adjusting while sitting in chair:
Turn knob left to tighten tension
Turn knob right to loosen tension
-Pull lever out to unlock & allow
chair to tilt back & forth.
-Push lever to lock. Chair will have slight
movement in locked position.
9/10

Warranty 3 years
Product Warranty –valid for Australian customers only
Officeworks Ltd warrants that this product will be free from defects and work as
intended for 3 years from the date of purchase by the original customer.
If the product has any defects or does not work as intended during the Warranty Period,
Officeworks will, at its election and at its expense, repair or replace the product.
This warranty does not apply:
• to cosmetic damage;
• to damage caused by consumables used in connection with the product (such as
cleaning products);
• where the product has not been used in accordance with all provided instructions;
• to damage arising from fair wear and tear;
• where the product has not been subject to reasonable use;
• where the product has been intentionally or negligent ly damaged; and/or
• if the customer has attempted to repair the product.
To make a claim under this warranty, please return your product with your receipt or
proof of purchase to your nearest Officeworks store or contact 1300 633 423.
This warranty is provided in addition to any rights you may be entitled to under the
Competitions & Consumer Act 2010.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goodsfail to be of acceptable
quality and the failure does not amount to a major failure.
Thank you for your purchase. Please retain your receipt to validate warranty.
If you would like to know more about our furniture products, please visit www.officeworks.com.au
10/10