J4C 20 User manual

MOUNTING INSTRUCTIONS J4C 20/85
MOUNTING INSTRUCTIONS J4C 20/85
VERY IMPORTANT:
PLEASE, FOLLOW THESE INSTRUCTIONS STEP BY STEP.IF THE CONNECTOR OF THE
BATTERY PACK IS PLUGED TO THE “BSR” PCB, BEFORE ARRIVING TO POINT 7, THE PCB
COULD BE DAMAGED.
KIT COMPONENTS
A 1 BSR PCB.
B 1 Lower baery support.
C 1 Baery pack.
D 1 Upper baery support.
E 3 Sheet metal Fixing screws
F 2 Plasc Fixing screws
AC
DE F
B
1. Remove the hand wheel screws and take it off. (Fig. 1).
2. Remove the 6 screws between the cover and the body of the actuator.(Fig.2).
3. Carefully remove the cover, in order to install the kit. (Fig.3).
4. Take the BSR PCB (A) from the KIT and connect it to the actuator PCB, by using the connector
Shown in picture. See (Fig.4). Fix it to the actuator metal plate, by using the Sheet metal fixing screw (E). See (Fig.5).
5. Put the lower baery support (B). See (Fig.6A). Fix it by using 2 Sheet metal fixing screws (E) (Fig.6B & 6C).
6. Place the baery pack (C) on the lower baery support (B) (Fig.7B). The baery cables should remain on the
boom part. Put the cables, as shown in the picture (Fig.7A).
7. Connect the baery cables to the BSR PCB (A), as per (Fig.7C).
8. Place the upper baery support (D) (Fig.8A) and fix it to the columns of the lower baery support (B), by using
the Plasc fixing screws (F) (Fig.8B & 8C).
9. BSR Configuraon NO or NC (Fig.9):
NC (normally close) SELDIR jumper ON.
NO (normally open) SELDIR jumper OFF.
10. Carefully replace the cover and be sure that the joint is correctly lodged in its place. See (Fig.10). Be sure that
any cable is not trapped between the cover and the body.
11. Fix the 6 screws, between the cover and the body. See (Fig.11).
12. Reassemble the hand wheel and fix it with the screws. See (Fig.12).
13. Fill in the blanks of the document inside the BSR KIT and send it back to the supplier, via fax or mail.
Now, the actuator is ready to work.
We strongly recommend to put the power on, send the actuator to an intermediate posion and check that,
aer pung the power off, the actuator goes to the pervious set-up posion (NC or NO).

ASSEMBLY INSTRUCTIONS
MOUNTING INSTRUCTIONS J4C 20/85

MOUNTING INSTRUCTIONS J4C 140/300
MOUNTING INSTRUCTIONS J4C 140/300
VERY IMPORTANT:
PLEASE, FOLLOW THESE INSTRUCTIONS STEP BY STEP.IF THE CONNECTOR OF THE
BATTERY PACK IS PLUGED TO THE “BSR” PCB, BEFORE ARRIVING TO POINT 4, THE PCB
COULD BE DAMAGED.
KIT COMPONENTS
A 1 BSR PCB.
B 2 Baery support.
C 2 Baery pack.
D 3 Sheet metal Fixing screws
E 1 Plasc clamp
A
BD
C E
1. Remove the hand wheel screw and take it off. (Fig. 1A & 1B).
2. Remove the 8 screws between the cover and the body of the actuator. (Fig.2).
3. Carefully remove the cover, in order to install the kit. (Fig.3).
4. Take the BSR PCB (A) from the KIT and connect it to the actuator PCB, by using the connector shown in the picture.
See (Fig.4). Fix it to the actuator metal plate, by using the Sheet metal fixing screw (D). See (Fig.5).
5. Place the 2 baery packs (C) as per picture (Fig.6A & 6B).
6. Place the baery supports (B), as per picture (Fig. 7A & 7B).
7. Fix the baery supports (B), with the sheet metal fixing screws (D) (Fig. 8A & 8B).
8. Connect the baery cables to the BSR PCB (A), as per (Fig.8C).
9. Put both baery cables (C) together with the plasc clamp (E) (Fig. 8D). Cut the remaining part of the plasc clamp (E).
10. BSR Configuraon NO or NC (Fig.9):
NC (normally close) SELDIR jumper ON.
NO (normally open) SELDIR jumper OFF.
11. Carefully replace the cover and be sure that the joint is correctly lodged in its place. See (Fig.10). Be sure that
any cable is not trapped between the cover and the body.
12. Fix the 8 screws, between the cover and the body. See (Fig.11).
13. Reassemble the hand wheel and fix it with the screw. See (Fig.12).
14. Fill in the blanks of the document inside the BSR KIT and send it back to the supplier, via fax or mail.
Now, the actuator is ready to work.
We strongly recommend to put the power on, send the actuator to an intermediate posion and check
that , aer pung the power off, the actuator goes to the pervious set-up posion (NC or NO).

ASSEBL INSTRUCTIONS
MOUNTING INSTRUCTIONS J4C 140/300