j5 create JUH450 User manual

USB 3.0 MULTI-ADAPTER
HDMI & 3-Port HUB
JUH450
User Manual
Manuel de l'utilisateur
Bedienungsanleitung
Manual del usuario
使用手冊
ユーザー マニュア
JUH450

JUH450
USB 3.0 MULTI-ADAPTER
HDMI & 3-Port HUB
JUH450
User Manual

Table of Contents
INTRODUCTIONS...................................................................................................................................3
System Requirements...................................................................................................................................3
Specifications ................................................................................................................................................4
Package Contents........................................................................................................................................5
GETTING STARTED.................................................................................................................................6
INSTALLATION FOR WINDOWS...........................................................................................................6
Device Driver Installation ............................................................................................................................6
Setup The Sound............................................................................................................................................9
Verify Device Driver Installation...............................................................................................................12
Uninstalling the Device Driver...................................................................................................................12
INSTALLATION FOR MAC ..................................................................................................................14
Device Driver Installation ..........................................................................................................................14
Setup The Sound..........................................................................................................................................15
Verify Device Driver Installation...............................................................................................................16
Uninstalling the Device Driver...................................................................................................................17
FUNCTIONS INSTRUCTIONS: WINDOWS 8、7................................................................................18
FUNCTIONS: WINDOWS XP............................................................................................................... 21
FUNCTIONS: MAC..............................................................................................................................26
TECHNICAL SUPPORT............................................................................................................................. 30
LIMITED WARRANTY.............................................................................................................................. 30

USB 3.0 MULTI-ADAPTER USER MANUAL
3
INTRODUCTIONS
Thank you for purchasing the j5create USB Multi-Adapter! This adapter acts as an external
graphics card for your MAC or PC. It allows you to add an additional display and 3 USB 3.0 ports
through your USB port.
With j5create multi-adapters, there is no need to open up your computer to add an
expensive graphics card, you simply load the drivers, plug in the adapter to the USB port, then
plug in the HDMI monitor cable into the adapter and you are ready. It supports three viewing
modes: primary, extended, mirror modes. With “plug & play” functionality between your
computer and 2nd monitor or projector, you will be able to create a new visual environment
in seconds.
j5create’s elegant multi-adapter series provides you with a fast and portable alternative
solution.
System Requirements
Microsoft Windows 8.1/ 8/ 7/ XP (32-bit or 64-bit)
Mac OS X 10.9 / 10.8 / 10.7 / 10.6
CPU: Intel 2 core Quad 2.33 GHz
RAM: 2 GB DDR2
Available USB port (USB 3.0 is recommended)
Note for Video Player:
*Windows XP users: “Windows Media Player” is recommended for video playback
*Windows XP users & MAC users: Some Windows XP & MAC products are not supported
by USB 3.0 at this time, therefore we suggest USB 2.0 for ‘office applications’ only; Video
Playback is not recommend due to USB 2.0 bandwidth limitations causing limited video
performance.

4
Specifications
Interface
Host Interface
USB 3.0 Male Type-A connector
Video Interface
HDMI Female connector
USB Port
USB 3.0 Female connector x 3 Ports
Power Jack
DC 5V (3.5mm)
Power
Power Mode
Bus-powered or Self-Powered
*** When you connect with high power-consumption
external HDD or USB devices that need bus power
more than 150mA. We recommend you to attach the
AC/DC power adapter included in your devices, or
purchase JUH450 AC/DC power adapter. (sold
separately)
Functions
Display
Video Playback: 1080P
Display resolution: 2048 x 1152 @ 32bit
Display Modes: Primary, Extended, Mirror
Display Rotation: 0°, 90°, 180°, 270°
Physical Specifications
Dimensions
Main body: 42.9(W)x 87(H)x14.2(D) mm
Cable length: 14.8 cm
Weight
Approximately 61.5 g (including cable)

USB 3.0 MULTI-ADAPTER USER MANUAL
5
Video Resolutions and Color Depth Support
Aspect Ratio
Resolution
Color Depth
Wide Screen Display
16:9 2048 x 1152 16,32 bits
16:10 1920 x 1200 16,32 bits
16:9 1920 x 1080 16,32 bits
16:10 1680 x 1050 16,32 bits
16:9 1600 x 900 16,32 bits
16:10 1440 x 900 16,32 bits
16:9 1360 x 768 16,32 bits
16:10 1280 x 800 16,32 bits
15:9 1280 x 768 16,32 bits
16:9 1280 x 720 16,32 bits
Standard Display
4:3 1600 x 1200 16,32 bits
4:3 1400 x 1050 16,32 bits
5:4 1280 x 1024 16,32 bits
4:3 1280 x 960 16,32 bits
4:3 1152 x 864 16,32 bits
4:3 1024 x 768 16,32 bits
4:3
800 x 600
16,32 bits
Package Contents
USB 3.0 Multi-Adapter JUH450
Quick Installation Guide
Driver CD

6
GETTING STARTED
Notes Before Installation
Install the driver completely before inserting the USB cable into your computer
Run the setup program as an administrator to avoid errors in installation
Connect the HDMI Cable for the display to the HDMI port on the JUH450 first before
connecting the USB cable to the computer
Un-install the previous driver first before installing the latest driver
1. Start the device driver installation (please refer to your PC system OS installation in the next
section) *Note: install driver completely before following steps 2 through 4.
2. Connect the USB 3.0 cable connector to the host laptop
3. Connect the HDMI cable for the display device
4. Your USB HUB port is now ready to use
INSTALLATION FOR WINDOWS
Device Driver Installation
This section illustrates the simple device driver installation guide for Windows 7 operating system.
When your computer is ready to use, insert the Driver CD into the CD-ROM drive. The setup
program should be launched automatically; if it doesn’t, go to Computer, click on your CD

USB 3.0 MULTI-ADAPTER USER MANUAL
7
drive, and manually run the setup CD. Double Click on Setup.exe to start.
※Make sure the USB cable is unplugged from your PC or Notebook before executing the
installation program.
1. The installation page will be launched. To
start click on Install the Latest Driver. Please
make sure you are connected to the internet
or press Install Driver to start the installation.
2. After pressing the installation option, the
InstallShield Wizard will launch, click Next
to continue.
3. Read the license agreement, check I
accept the terms of the license agreement,
click Next >
4. When the Install Shield Wizard is complete,
select Yes, I want to restart my computer
now. Click Finish to restart.
5.
After restarting your computer connect the
USB 3.0 MULTI-ADAPTER USB cable to your
PC or Notebook. The Installing device
driver software message will pop-up.
6. Windows 7:
When the driver software has been
installed successfully the message to the
right will appear on your computer.
Windows XP: An icon ( ) will be seen
on the lower right toolbar. Your driver
software was installed successfully when
the message to the right is shown.
The display functions of the USB3.0 Multi-Adapter will be activated after the computer has
been restarted. You might see the mirror display shown on the display device.

8
Windows 8
、
7:
You can modify the corresponding
position of each extend display via
display settings. Go to START →
Control Panel →Appearance and
Personalization →Adjust screen
resolution
※or Right click on the desktop and go
to Screen Resolution
When the Screen Resolution window
pops up, you can identify each
monitor’s number by clicking Identify.
You can drag the monitor to your
preferred location.
Windows XP:
You can modify the corresponding
position of each extended display via
display settings.
Go to Start →Control Panel →Display
Properties →Settings
When the Display Properties window
appears, each monitor’s number can
be identified by clicking Identify.
You can drag the monitor to your
preferred location.
Note:
If your internal graphics card has Dual Display Ports…..
When using one USB 3.0 MULTI-ADAPTER:
The display device that is connected to the 2nd HDMI port will be numbered as the 3rd monitor
and the display device that is connected to the USB 3.0 MULTI-ADAPTER will be numbered as
the 2nd monitor.

USB 3.0 MULTI-ADAPTER USER MANUAL
9
Setup The Sound
Setup The Sound on Windows 8, 7
Microsoft’s audio system restricts the audio function to one output at a time; therefore, when
using the USB HDMI multi-display adapter only one output will receive audio.
The following explains how to set-up and change the default sound output from the display
device connected with the USB 3.0 HDMI Display Adapter.
1. Go to “Control Panel> Hardware and Sound” and select “Changes system sounds”
2. The speaker options , for single and Multi- USB 3.0 HDMI Display Adapters, are shown below.
Single USB 3.0 HDMI Display Adapter
Multi-USB 3.0 HDMI Display Adapter

10
Note:
1. The speakers are numbered according to the number if USB ports detected by your
computer system.
2. The Default sound will output from the USB 3.0 HDMI Display Adapter with the greatest
number of USB ports.
3. To change the default sound output, use your mouse to right click in the sound options box
on your desktop, then select “Test” to choose which speaker you want to use as your
default.
4. Select the Speaker you want and then click “Set Default”
Setup The Sound on XP
Microsoft’s audio system restricts the audio function to one output at a time; therefore, when
using the USB HDMI multi-display adapter only one output will receive audio.
The following explains how to set-up and change the default sound output from the display
device connected with the USB 3.0 HDMI Display Adapter.
1. Go to “Control Panel> Sounds, Speech, and Audio Devices” and select “Changes the
speaker settings”.

USB 3.0 MULTI-ADAPTER USER MANUAL
11
2. The speaker options, for single and Multi- USB 3.0 HDMI Display Adapters, are shown below.
Single USB 3.0 HDMI Display Adapter
Multi-USB 3.0 HDMI Display Adapters
Note:
1. The speakers are numbered according to the number if USB ports detected by your
computer system.
2. The Default sound will output from the USB 3.0 HDMI Display Adapter with the greatest
number of USB ports.
3. Select “the Default device” you want, and click “apply”. then click “ Volume” to choose
which speaker you want to use as your default.

12
Verify Device Driver Installation
Follow the steps below to verify the driver installation status of the USB 3.0 Multi-Adapter
Windows8,7:
Right Click My Computer Manager

Device Manager

click +sign of
Network adapter & Sound, video and
game control & Universal Serial Bus
controllers
Windows XP:
Right Click My Computer, Manager →Device Manager click + sign of Display Adapter &
Network adapter & Sound, video and game controllers & Universal Serial Bus controllers
Uninstalling the Device Driver
*Unplug the USB Cable of the USB 3.0 MULTI-ADAPTER before uninstalling the driver

USB 3.0 MULTI-ADAPTER USER MANUAL
13
1. Click Start→Control Panel →Programs
and Features→Uninstall or change a
program Select j5 USB 3.0 MULTI-
ADAPTER... Click Uninstall
2. A message will appear confirming that you
want to un-install the application. Click ‘ok’ to
continue.
3. When the driver is completely
uninstalled, select “Yes, I want to restart
my computer now.” Click Finishto
restart.

14
INSTALLATION FOR MAC
Device Driver Installation
Installing the device driver enables your computer’s operating system to recognize the USB3.0
Multi-Adapter. Be sure that you are referring to the appropriate installation procedure before
you begin installing.
※Make sure the USB cable is unplugged from your Mac Desktop or Mac Notebook before
executing the setup program.
This section illustrates the device driver installation procedure for a computer running Snow
Leopard.
1. Insert the Driver CD into the CD-ROM drive;
and run the .dmg file to load drivers in the
mac install folder
2. The installation page will be launched;
To begin installation click on start Get Last
Driver online, please make sure you are
connected to the internet or press
to start the installation.
3. Click Continue to proceed
4. Type in your password and click OK
5. Click Continue Installation

USB 3.0 MULTI-ADAPTER USER MANUAL
15
6. Installation is processing…This will take a
few moments
7. Click Restart to complete the software
installation
Setup The Sound
Mac audio system restricts the audio function to one output at a time; therefore, when using
the USB HDMI multi-display adapter only one output will receive audio.
1. GO , and then “System Preferences”

16
2. Go to the “System Preferences” and select “Sound”
3. The speaker“Output” options , for single and Multi- USB 3.0 HDMI Display Adapters, are
shown below. You can select a device for sound output by clicking it.
•Single USB 3.0 HDMI Display Adapter
•Multi-USB 3.0 HDMI Display Adapter
Verify Device Driver Installation
Follow the steps below to verify the driver installation status of the USB 3.0 Display Adapter
1. GO , select About This Mac and
select More Info
…
2. The picture shows the installation process for the
USB 3.0 Multi-Adapter

USB 3.0 MULTI-ADAPTER USER MANUAL
17
Uninstalling the Device Driver
1. Unplug the USB Cable of USB 3.0
MULTI-ADAPTER from the USB port
2. To un-installation, please press the
Uninstall Driver icon
3. Click Open to proceed
4. Click Uninstall and restart to proceed
5. Type in your password to allow un-
installation and click OK to proceed
6. Restart your system.

18
FUNCTIONS INSTRUCTIONS: WINDOWS 8,7
Display Resolution
Fast access to Display Resolution settings
The resolution list will show when you
move the cursor over Display Resolution
.
Select your desired resolution.
Default resolution: 1024 x 768 x 32 bit
Display Orientation
The Orientation allows you to turn the
display on the device that is connected
to the USB 3.0 MULTI-ADAPTER
Display Mode
Extended mode (Default)
This feature allows the display device
attached to the USB 3.0 MULTI-ADAPTER
to work as an “extended” display of the
on-board screen.
You can adjust the position by clicking
the number of the display first and then
select Extend these displays and click
Apply

USB 3.0 MULTI-ADAPTER USER MANUAL
19
Mirror mode-Duplicate
This feature allows the same contents of
the on-board screen to be displayed on
the screen connected to the USB 3.0
MULTI-ADAPTER
You can select Duplicate these displays
and click Apply
Note:
The resolution for the secondary and
primary displays must be the same when
using Mirror Mode (This may be lower than
the preferred resolution for the display).
Only 2 displays can be mirrored at the
same time. Windows 7 OS may have other
limitations.
Primary mode
When you want to switch the enabled
monitor as the main display and extend
the view to the on-board screen.
Choose the Number
of the main display
you want and click on
Make this my
main display.
Off mode
You can turn one display on while the
other is off
Select Show desktop only on 1 and the
2nd display will be off
Select Show desktop only on 2 and the
1st display will be off