j5 create JUA350 User manual

JUA350 Manual
USB 3.0 HDMI Display Adapter
User Manual

2
Table of Contents
INTRODUCTION ........................................................................................................................... 3
GETTING STARTED –Notes for Before Installation ................................................................... 7
INSTALLATION FOR WINDOWS 8,7 .................................................................................... 7
INSTALLATION FOR WINDOWS XP................................................................................... 17
INSTALLATION FOR MAC.................................................................................................. 26
FUNCTIONS INSTRUCTIONS: WINDOWS 8, 7 .................................................................. 34
FUNCTIONS INSTRUCTIONS: WINDOWS XP .................................................................... 40
FUNCTIONS INSTRUTIONS: MAC ...................................................................................... 46
TROUBLE SHOOTING................................................................................................................. 50
TECHNICAL SUPPORT ............................................................................................................... 52
REGULATORY COMPLIANCE................................................................................................... 53
WARRANTY OF j5create .......................................................................................................... 54

USB DISPLAY ADAPTER USER MANUAL
3
INTRODUCTION
Thank you for purchasing the j5 create(JUA350) USB 3.0 HDMI Display Adapter! This
USB to HDMI adapter acts as an external video card for your MAC or Windows
compatible PC or Laptop. It allows you to add an additional HDMI monitor/display
through any available USB port. There is no need to open up the computer to add an
expensive video card. With the (JUA350) you simply load the drivers, plug in the
adapter to the USB port, then plug in the HDMI monitor cable into the adapter and
you are ready.
The j5 create JUA350 supports three viewing modes and HDMI audio. Primary and
Extended mode allow you to have individual applications open on each monitor
vastly improving productivity and extend your desktop across multiple displays, which
is great for spreadsheets. Mirroring mode is used to clone one screen onto another,
which is ideal for presentations. In addition you can “Plug & Play” between your
computer and a 2nd monitor or projector, to create new visual environments in
seconds.
j5 create has developed this compact design for the sophisticated user who cares
about function as well as elegance.
Functions
Easily add an additional display instantly through the USB3.0 and HDMI
connection.
Video playback performs at 1080P HD with a resolution of up to 2048 x 1152.
Add an additional monitor without adding an expensive, internal video card,
avoiding complicated installation
Hot swappable USB enables you to add or remove monitors without
rebooting your system
Move and view your large spreadsheets across two screens without
overlapping windows
Multitask with larger landscape/desktop space
Ideal for viewing multiple windows at the same time
Great for multitasking in a wide variety of applications including: Phone
centers, Stock Markets, Hospitals, Graphic Design, Editing, Accounting, Etc.
A must have for surfing the web and working on your email/facebook/twitter
accounts all at the same time.
Highlighted Features
Supports display resolution:2048 x 1152 @ 32bit
Super Speed USB 3.0 up to 5 Gbit/s
Supports 1080P Video Playback
Plug-and-Play USB connectivity
Allows for up to 4 adapters in Windows
Allows for up to 2 adapters in Macs

USB DISPLAY ADAPTER USER MANUAL
4
Supports Display Modes: Primary, Extended, Mirror
Display Rotation: 0°, 90°, 180°, 270°
Audio imbedded 8kHz~48kHz
Aluminum enclosure that is non-toxic and recyclable
Easy driver install
Usage
Editor:
•Efficient editing of documentation on one screen and researching
reference materials on the other
Presentation:
•Use mirror mode while your laptop is plugged into a projector through the
USB 3.0 Display Adapter
•Use Primary mode to have two monitors and projector for creative displays
Office:
•Dual display scenario: view large spreadsheets across 2 screens with display
continuity. (For example: Excel document)
•Independent: using desk space and doing multi-job at the same time-
increase efficiency.
•Read and reply to email on one screen and open
attachments on the other
Graphics Workstation:
•Design and check reference material at the same time.
•More space for tablets and photo/video editing
Entertainment:
•Watch TV/Movie while searching the program preview
•Play games online on one screen with the strategy guide on the other
screen
Stock Market Trading:
•Monitor multiple stock markets and market news simultaneously
Coding/Programming:
•Allows effective code programming on one screen and software program
companion on the other screen.

USB DISPLAY ADAPTER USER MANUAL
5
Required Environments
Microsoft Windows 8, 7, XP (32-bit or 64-bit) Compatible
Mac OS X Mt. Lion/ Lion /Snow Leopard Compatible
Available USB port ( USB 3.0 recommended)
Minimum System Requirements
QTY
1~2 Dongle
3～4 Dongles
CPU
Intel 2 Quad 2.33 GHz or
above
Intel i5 3.10 GHz or above
RAM
2 GB or Higher
4 GB or Higher
Full HD
Video
Playing Video on the extended monitor
CPU: Intel Core i5 processor with 3.1 GHz or Higher
RAM: 4 GB memory or higher
※Higher Processor recommended for Multi-Displays and optimal
performance.
Note:
USB HUB is not recommended for USB 3.0 display adapter
Note for Video Player:
*Windows 8 & 7 user: “Windows Media Player” is recommended for video playback
*Windows XP user & MAC user: Windows XP & MAC products are not supported
by USB 3.0 at this time, therefore we suggest USB 2.0 for ‘office application’ only;
Video Playback is not recommend due to USB 2.0 bandwidth limitations causing
limited video performance.
Note:
To ensure that your device is equipped with the most current driver, please visit
our website at www.j5create.com and install the latest driver for this model.
Physical Specifications
Model: JUA 350
Interface
Host Interface
USB 3.0 Female Type-A Connector
Video & Audio
Interface Interface
HDMI Female Connector
Power
Power Mode
Bus-powered or Self- Powered
Power Consumption
≦500mA
Physical Specification
Housing Material
Aluminum

USB DISPLAY ADAPTER USER MANUAL
6
Dimensions
Main body: 41(W)x 72(H)x14(D) mm
Cable length: 200 mm
Weight
Approximately 53 g
Resolutions and Color Depth
Aspect Ratio
Resolution
Color Depth
Wide Screen Display
16:9
2048 x 1152
16,32 bits
16:10
1920 x 1200
16,32 bits
16:9
1920 x 1080
16,32 bits
16:10
1680 x 1050
16,32 bits
16:9
1600 x 900
16,32 bits
16:10
1440 x 900
16,32 bits
16:9
1360 x 768
16,32 bits
16:10
1280 x 800
16,32 bits
15:9
1280 x 768
16,32 bits
16:9
1280 x 720
16,32 bits
Standard Display
4:3
1600 x 1200
16,32 bits
4:3
1400 x 1050
16,32 bits
5:4
1280 x 1024
16,32 bits
4:3
1280 x 960
16,32 bits
4:3
1152 x 864
16,32 bits
4:3
1024 x 768
16,32 bits
4:3
800 x 600
16,32 bits
Package Contents
USB 3.0 Display Adapter(JUA350)
HDMI to DVI Convertor
Quick Installation Guide
Driver CD with E-Manual

USB DISPLAY ADAPTER USER MANUAL
7
GETTING STARTED –Notes for Before Installation
Install driver completely before inserting the USB 3.0 Display Adapter USB
Cable into your computer
Run the setup program as an administrator to avoid errors in installation
Uninstall the previous driver first before updating the latest driver
Connect the HDMI connector or the HDMI to DVI convertor of the USB 3.0
HDMI Display Adapter to the HDMI or DVI cable of the display device. Then
connect the device to the USB port of the computer
It is recommended to use an independent power supply for USB Hub while
multiple dongles are connected to the USB Hub
The display screen will flash during installation
INSTALLATION FOR WINDOWS 8,7
Device Driver Installation
This section illustrates the procedure for device driver installation for Windows 7. To
start, insert the Driver CD into your computer’s CD-ROM drive. The setup program
should be launched automatically. If Autorun does not begin, go to “Computer”, Click
on your optical drive, and manually run the setup CD by double-clicking on
“Setup.exe”
※Please make sure the USB cable of USB 3.0 Display Adapter is unplugged from your
PC or Notebook before executing the installation program.
1. The installation page will be launched. To start click on “ Install the Latest Driver”.
Please make sure the network is available or press “Install Driver” to start the
installation

USB DISPLAY ADAPTER USER MANUAL
8
2. After pressing the installation option, the InstallShield Wizard will launch, click
Next> to continue
3. Read the license agreement and check “I accept the terms of the license
agreement.” Click Next > to accept it and continue.

USB DISPLAY ADAPTER USER MANUAL
9
4. Driver installation proceeding…..
5. When Install Shield Wizard is complete, select “Yes, I want to restart my computer
now.” Click Finish to restart.

USB DISPLAY ADAPTER USER MANUAL
10
6. After rebooting connect the external display device (monitor/ projector) to the
HDMI connector or the DVI connector of USB Display Adapter and turn on the
display device.
7. Connect the USB 3.0 Display Adapter into an available USB port of a PC or
Notebook, After Inserting the USB 3.0 Display Adapter into an USB port, the
“Installing device driver software” message will pop up.
If the Driver software was installed successfully the following message should
appear:
If you’re not going to install another USB 3.0 Display Adapter, restart your PC. The
functions of the USB 3.0 Display Adapter will be activated after the computer restarted.
Multi USB 3.0 Display Adapter Installation
For installation of multiple USB 3.0 Display Adapters, during the “Install Shield Wizard
complete” step, select “No, I will restart my computer later.” and click Finish to
continue next step below

USB DISPLAY ADAPTER USER MANUAL
11
A. Connect all external display devices (monitor/ projector) to the HDMI /DVI
connector of USB 3.0 Display Adapters and switch power on.
B. Connect the USB 3.0 Display Adapter into an available USB port of a PC or
Notebook.
After Inserting an USB 3.0 Display Adapter into a USB port, the systems will
automatically start the installation procedure and the prompt message will pop-up
on the task bar.
The Device driver software was installed properly,
if you are going to install more USB 3.0 Display Adapters, repeat step A& B or restart
computer.
The functions of the USB 3.0 Display Adapter will be activated after the computer
restarted. You might see the extend display shown on the display device.
You can modify the corresponding position of each extend display via display settings.
Go to “START” →“Control Panel” →“Appearance and Personalization” →“Adjust
screen resolution”
※Right-click on the desktop and go to “Screen Resolution”

USB DISPLAY ADAPTER USER MANUAL
12
When the ‘Screen Resolution’ window appears, each monitor’s number can be
identified by clicking “Identify.”Drag the monitor to the location you want.
Setup The Sound
Microsoft’s audio system restricts the audio function to one output at a time; therefore,
when using the USB HDMI multi-display adapter only one output will receive audio.
The following explains how to set-up and change the default sound output from the
display device connected with the USB 3.0 HDMI Display Adapter.
1. Go to “Control Panel> Hardware and Sound” and select “Changes system sounds”

USB DISPLAY ADAPTER USER MANUAL
13
2. The speaker options , for single and Multi- USB 3.0 HDMI Display Adapters, are
shown below.
Single USB 3.0 HDMI Display Adapter
Multi-USB 3.0 HDMI Display Adapter
Note:
1. The speakers are numbered according to the number if USB ports detected by
your computer system.
2. The Default sound will output from the USB 3.0 HDMI Display Adapter with the
greatest number of USB ports.
3. To change the default sound output, use your mouse to right click in the sound
options box on your desktop, then select “Test” to choose which speaker you
want to use as your default.

USB DISPLAY ADAPTER USER MANUAL
14
4. Select the Speaker you want and then click “Set Default”
Verify Device Driver Installation
The following procedure helps you to verify the driver installation status of the USB 3.0
Display Adapter.
Right-click “My Computer” “Manager” “Device Manager” click “+” sign of
“Sound, video and game controllers” & “Universal Serial Bus controllers”
The picture below shows the installation process for a Single USB 3.0 Display Adapter

USB DISPLAY ADAPTER USER MANUAL
15
The picture below shows the installation process for a Multiple USB 3.0 Display Adapter
Device Driver Un-installation
※Unplug the USB 3.0 Display Adapter before un-installing the driver.
1. Click “Start”→Control Panel →Programs and Feature→Uninstall or Change a
Program Select j5 HDMI DISPLAY ADAPTER ... Click Uninstall
2. A message will appear asking if you want to remove the selected application.
Click ‘ok’ to continue.

USB DISPLAY ADAPTER USER MANUAL
16
3. Driver un-installation proceeding….
4. When the driver uninstall is completed select “Yes, I want to restart my computer
now.” Click Finish to restart.

USB DISPLAY ADAPTER USER MANUAL
17
INSTALLATION FOR WINDOWS XP
Device Driver Installation
This section illustrates the procedure for device driver installation for Windows XP. To
start, insert the Driver CD into your computer’s CD-ROM drive. The setup program
should be launched automatically. If Autorun does not begin, go to “Computer”, Click
on your optical drive, and manually run the setup CD by double-clicking on
“Setup.exe”
※Please make sure the USB 3.0 Display Adapter USB cable is unplugged from your PC
or Notebook before executing the installation program.
1. The installation page will be launched. To begin installation click on “ Install the
Latest Driver” , please make sure the network is available or press “Install Driver” to
start the installation
2. After pressing the installation option, the InstallShield Wizard will launch, click
Next> to continue

USB DISPLAY ADAPTER USER MANUAL
18
3. Read the license agreement and check “I accept the terms of the license
agreement.” Click Next > to accept it and continue.
4. Driver installation proceeding…..
5. When Install Shield Wizard is complete, select “Yes, I want to restart my computer
now.” Click Finish to restart.

USB DISPLAY ADAPTER USER MANUAL
19
6. After your computer is rebooted, connect the external display device (monitor/
projector) to the HDMI/DVI connector of USB 3.0 Display Adapters and turn it on.
7. Connect the USB 3.0 Display Adapter into an available USB port of a PC or
Notebook, After Inserting the USB 3.0 Display Adapter into an USB port, the
“Installing device driver software” message will pop up.
An icon ( ) will be seen on the lower right toolbar.
The message pictures below shows Driver software is installed successfully.
If you’re not going to install another USB 3.0 Display Adapter, restart your PC. The
functions of the USB 3.0 Display Adapter will be activated after the computer restarted.
Multi-USB 3.0 Display Adapter Installation
For installation of multiple USB 3.0 Display Adapters, during the “Install Shield Wizard
complete” step, select “No, I will restart my computer later.” and click Finish to
continue next step below

USB DISPLAY ADAPTER USER MANUAL
20
A. Connect all external display devices (monitor/ projector) to the HDMI/DVI
connector of USB 3.0 Display Adapters and switch power on.
B. Connect the USB 3.0 Display Adapter into available USB port of PC or
Notebook.
After Inserting an USB 3.0 Display Adapter into a USB port, the systems will
automatically start the installation procedure and the prompt message will pop-
up on the task bar.
The Device driver software was installed properly, if you are going to install more USB
3.0 Display Adapters, repeat step A & B or restart computer
The functions of the USB 3.0 Display Adapter will be activated after the computer
restarted. You might see the mirror display shown on the display device.
You can modify the corresponding position of each extend display via display settings.
Go to “START” →“Control Panel” →“Appearance and Personalization” →“Display
Properties”→“Settings”
When Display Properties windows
appears, each monitor’s number can
be identified by clicking “
“ identify”
Drag the monitor to the location you
want.