JabloCom EYE-02 User manual

GSM Security Camera
EYE-02

Camera EYE-02:
Package content:
12
4
3
EYE-02 camera
1Camera lens
2PIR motion sensor
3Green light 4Red light
5Infra red ilumination
6GSM Antenna
7Power button
8AC adaptor socket
9USB connector
10 Battery cover
Battery
Instalation CD
Key-fob
6
8
9
7
10
5
Screwdriver
User manual
AC adapter
Wall mounting screws
Connecting cable
USB cable
Page 2

EYE
-
02 User Guide
-
1
-
INDEX
INDEX ........................................... 1
INTRODUCTION – BASIC FEATURES ....... 1
GETTING STARTED ............................ 2
Your Camera ..........................................2
Camera installation ................................2
CAMERA FUNCTION.......................... 4
Camera Modes .......................................4
Remote control ......................................4
Contacts .................................................5
Detectors................................................6
P R motion detector (P R) ..............6
Motion- n-Picture detector (M P) ..6
Noise detector (SOUND) ................6
Glass-break detector (GBS) ............6
Tilt a vibration detector (T LT) .......6
Profiles ...................................................7
HOME.............................................7
OUTDOOR ......................................7
GARAGE .........................................7
CARE ..............................................7
SHOP ..............................................7
CONF G mode ........................................9
Configuration with PC ............................9
Event Reports .......................................10
Call Control .......................................... 11
Night view ........................................... 11
Battery saving mode ............................ 11
CONFIGURATION............................ 12
PC ........................................................ 12
Web ..................................................... 12
SMS ..................................................... 12
Control commands ...................... 12
Config commands........................ 13
Switch the camera On and Off ............ 14
Micro SD card ...................................... 14
Reset to factory defaults ..................... 14
GSM network setting ........................... 14
Video record setting ............................ 15
Other Video Options ................... 16
MONITORING ............................... 16
EXTERNAL WIRELESS DEVICES ............ 17
OUTDOOR INSTALLATION ................. 17
MAINTENANCE ............................. 17
TROUBLESHOOTING ........................ 17
TECHNICAL SPECIFICATION ................ 18
Battery information ............................. 18
Warranty ............................................. 18
Safety instructions ............................... 19
INTRODUCTION – BASIC FEATURES
EYE-02 is a security and monitoring camera which communicates wireless via GSM network
EYE-02 integrates a group of detectors which allow the user to detect an intruder or just movement:
PIR m ti n detect r reflects temperature change
S und detect r microphone notices a noise above a defined level
Glass-break detect r recognizes a specific sound of breaking window glass
Tilt and vibrati n detect r recognizes any unwanted change in camera‘s position and tilt
M ti n in picture reflects changes in picture by taking snaps regularly and
comparing them
EYE-02 is simple to install and set-up (for D Y installation)
EYE-02 triggers an alarm and sends an alert record via MMS, e-mail, SMS or voice call. The
copies of pictures and videos might be stored on the memory card or can be stored at a
web server.
EYE-02 allows 24 hour monitoring via night view mode
EYE-02 is compatible with a wide range of external wireless devices

EYE
-
02 User Guide
-
2
-
GETTING STARTED
YOUR CAMERA
See the camera picture on first page of this manual.
1 Camera lens 6 GSM Antenna
2 PIR m ti n sens r 7 P wer butt n
3 Green light 8 AC adapt r s cket
4 Red light 9 USB c nnect r
5 Infra red illuminati n 10 Battery c ver
CAMERA INSTALLATION
Note: Please ensure you have a SIM card provided by your GSM operator ready before you start!
If the SIM card is protected by PIN please put it into your mobile phone first and disable the PIN
protection.
Please follow the detail instruction in QU CK GU DE to simplify the camera installation and first use.
Unpack the camera and check the package content
Warning: Use only batteries, chargers and enhancements approved by JABLOCOM or use with this particular
model. The use o any other types may invalidate any approval or warranty, and may be dangerous.

EYE
-
02 User Guide
-
3
-
Open the camera battery cover, insert the S M card and the battery, close the cover
nstall the camera to the selected position
Connect the AC adaptor – camera will start up automatically
Battery c ver
Insert SIM card Insert battery
M unt the camera h lder firmly
Adjust the camera p siti n Rem ve lens pr tecti n
Plug the p wer cable t camera
Plug the p wer adapt r t wall, wait 10 sec nds and check the camera
Call camera number fr m y ur
m bile ph ne Press butt n and then butt n , check the green light n camera

EYE
-
02 User Guide
-
4
-
CAMERA FUNCTION
CAMERA MODES
The EYE-02 camera has three main working modes:
S
SL LE EE EP P ,
W
WA AT TC CH H and
C
CO ON NF FI IG G .
M de Descripti n Butt n n Rem te
c ntr l
SLEEP
SLEEP mode is a stand-by mode of camera. The camera doesn’t detect any
movement in the targeted area and the major detectors are disabled. The
only active detectors are the those which protect camera itself against the
unwanted manipulation by some intruder.
WATCH n WATCH mode camera guards fully the targeted area, all detectors are
active
CONF G
CONF G mode allows the user to change camera’s settings, enroll a new
external device (as remote control) to cooperate with camera or enroll a new
user contacts (see more details in CONF G mode chapter)
press and
together
REMOTE CONTROL
The package contains a wireless remote control (type RC-86), which can be used
to switch between camera modes – see detail of each button’s function in the
table above.
Camera confirms a change of mode by LED lights on the front panel and also by a
beep signal.
Camera
m de LED lights signaling S und signal
WATCH Lights are Off One long
beep
SLEEP Green light is permanently
On
Two long
beeps
CONF G Red and Green lights blink
slowly together
Three long
beeps
ENROLL Red and Green lights swap
blinks slowly
-
ERROR Red light is permanently
On
Four short
beeps

EYE
-
02 User Guide
-
5
-
CONTACTS
Camera can report the events to the mobile phones (voice call , text message , MMS ) or to
the e-mail addresses. Up to 10 different phone numbers and 10 e-mail addresses can be saved on
the list.
The most comfortable way how to list the contacts is to use the JabloTool software on PC.
The reporting level might be selected for each contact. Three levels (High, Middle, Low) mean how
many events should be reported to the contact. Low level reported user will be reported the
ALARMS only, Middle level means that also some other important events will be reported to the
contact.
JabloTool also offers to block some of report channels (calls , SMS , MMS ) by unticking an
appropriate box in the contact line.
New contact may be also entered by an SMS command:
CONF G CONTACT <contact> where <contact> means the phone number or e-mail address
e.g. C ONFIG C ON T AC T + 4 8 5 5 5 7 8 9 4 5 6
C ON F I G C ON T AC T e m a i l @ h t m ai l . c m
New phone number might be also added by calling the camera directly from a new phone number
while camera is switched into
C
CO ON NF FI IG G mode. f there are not any phones saved in a contact list (a
new camera or after factory reset) the camera switches automatically to
C
CO ON NF FI IG G mode and waits for
an incoming call.

EYE
-
02 User Guide
-
6
-
DETECTORS
Camera EYE-02 integrates a wide range of detectors. This sophisticated solution combining various
types of detectors enables the user to protect the desired area from a wide range of points of view.
This chapter briefly describes individual detector’s principles necessary for correct setting of
detection.
P R MOT ON DETECTOR (P R)
P R detector or a Human Body Detector is the most common type of professional security systems
detectors. P R can detect even very small changes of temperature differences in front of the camera.
MOT ON- N-P CTURE DETECTOR (M P)
The key principle of this detector is derived from a professional surveillance camera system – DSP
(digital signal processor). t permanently analyzes the scene and can detect any change in picture.
A sophisticated digital algorithm provides a very good resistance to false alarms caused by non-
essential changes in pictures (getting dark, switching on the street lamps, etc).
A user can simply mask a part of a picture not to detect changes in this part (mask of street traffic)
and set the sensitivity according to the size and velocity of change in picture.
As the DSP method is energy demanding, M P is usually activated after some alert from SOUND or
P R detector.
NO SE DETECTOR (SOUND)
Noise detector uses a microphone to check the surrounding for any sound above the preset level.
Sensitive electronic filtering can detect the air pressure changes – this principle allows detection of
door or window opening at a long distance.
GLASS-BREAK DETECTOR (GBS)
Glass-break detector uses digital analysis of sound from the microphone and is able to detect a
characteristic sound of breaking a window up to 9 meters away.
The Door-Opening-Detection is a special type of detection which use the acoustic signal filtering. t
allows to detect the infrasonic wave (pressure wave) caused by door or window opening.
GBS sensor might be used for indoor installation only.
TLT A V BRAT ON DETECTOR (T LT)
Built-in tilt and vibration detector can detect an unwanted manipulation with the camera, e.g.
stealing the camera body or changing camera position.
As a vibration detector is very sensitive it should not be use for outdoor installation to prevent the
false alarms caused by a blow of wind.
Note: The detectors are optimized to application in rooms ith max dimension up-to 10meters.

EYE
-
02 User Guide
-
7
-
PROFILES
Camera offers fast and simple setting of all necessary detector parameters by selecting one of pre-
defined PROF LEs. These profiles are well suitable for most camera applications. f necessary the
profile may be further tuned by the user.
HOME
HOME profile has been designed for camera installation inside
a building (house, flat, office). During WATCH mode, there are
no movements of people, no blows of wind, no significant
temperature changes, or loud noise etc. expected.
OUTDOOR
OUTDOOR profile fits best camera installation outside your
home.
The camera significantly reduces its detectors’ sensitivity in
OUTDOOR as there are many possible sources which could
cause a false alarm triggering (sunshine, animals, street noise,
wind, ...).
Note: Although the camera housing comes ith a basic ater
protection e strictly recommend placing the camera into a
plastic cover to be protected against the rain and ind once it
is installed outdoor.
GARAGE
This profile is suitable for installation inside your home, similar
to HOME profile. Additionally, the GARAGE profile provides a
30-second entrance delay. t allows you to open the garage or
home entrance door first and switch the camera to SLEEP
during this delay.
CARE
Profile CARE has been especially designed for monitoring small
children and elderly or disabled people.
The camera used in CARE profile allows the user to leave
their home, stay in a short distance away from home and
watch their sleeping baby or ill grandmother at the
same time.
The camera will be activated by movement, by
sound (i.e. baby crying) or a PAN C alarm
might be triggered by a personal wrist button.
The entrance and exit delay is preset to 5 second.
Note: The internal acoustic camera signals are disabled in CARE
profile. Also TILT detector is blocked to allo the camera
manipulation.
SHOP
The most powerful profile is SHOP. All detectors are active in
this mode, including the permanent process of “Motion in
Picture” detection. This profile offers the highest quality of
permanent monitoring, consequently it is the highest energy
consumption profile.
This perfectly fits the places with temporary monitoring
request, as shops, office corridors and reception areas.

EYE
-
02 User Guide
-
8
-
Sens r Parameter
HOME
OUTDOOR
GARAGE
CARE
SHOP
PIR
Active ON ON ON ON ON
Sensitivity High Low Middle Middle Middle
Analysis level Middle Middle Middle Middle Middle
Reaction nstant Alert only 60 s delay 5 s delay 30 s delay
MIP
Active Wake at Alert ON Wake at Alert Wake at Alert ON
Sensitivity Middle Low Middle Middle High
Analysis level Low Middle Middle Middle Middle
Reaction nstant nstant 60 s delay nstant 30 s delay
GBS
Active ON OFF ON OFF ON
Sensitivity Middle Middle Middle
Reaction nstant 60 s delay nstant
SOUND
Active ON OFF ON ON ON
Sensitivity Middle Low Middle Low
Analysis level Middle Middle Middle Middle
Door detection OFF OFF OFF OFF OFF
Reaction 30 sec nstant 60 s delay nstant Alert only
TILT
Active ON ON ON OFF ON
Sensitivity Low Low Middle Middle
Analysis level Middle High Middle Middle
Vibration sensor
disabled No Yes No Yes No
Reaction nstant Alert only nstant nstant
Exit delay 15 sec 60 sec 60 sec 5 sec 15 sec
Post ALERT wake-up for time
period 60 sec 60 sec 60 sec 60 sec 60 sec
Reports are disabled after first
ALARM for 5 min 5 min 5 min 5 min 60 sec
Maximum number of reported
ALARMs per one watching
period
10 10 10 10 20
Save ALERT records into the
event log No Yes No No Yes
Capture slow video of P R and
MiP activity in SLEEP mode No No No No Yes
ncrease the detector
sensitivity during ALERT state No No No No No
Two independent ALERTS
cause an ALARM No Yes No No No
Green LED blinks during
WATCH No No No Yes No
Disable an acoustic signaling of
camera control No No No Yes No
Disable an acoustic signaling of
exit delay No No No Yes No