jablotron CA-1802 athos User manual

CA-1803BT, CA-1802 User manual – mode 3 - 1 - MHF57100
The “Athos” CA-1802 and CA-1803BT GSM pagers
Thank you very much for buy ng our CA-1802/CA-1803BT GSM pager. Now you w ll always be able
to f nd where you left your car. Jablotron s.r.o.
Alarm
When an alarm is triggered, warning SMS messages will be sent to all phones (TE 1 to TE 4)
and these phones will also be called with a siren sound
1
.
Remote control y SMS instructions
You can operate the car alarm remotely via SMS instructions sent from an authorized phone
(TE 1 to TE 4). Factory default instruction texts are shown in the following table. If an SMS is
sent from an unauthorized phone a valid user code must be entered before the instruction (e.g.
USER IMO).
In the case that you do not remember particular SMS instruction(s) you can
ask for help by sending a HELP instruction
Remote control from an unauthorized phones
You can operate the car alarm via SMS instructions sent from arbitrary mobile phone, even an
unauthorized one. In that case, the user code must be inserted at the start of every SMS
instruction, separated by a space. Example: MYCODE STATUS. The factory default value of
user code is USER. The code can be modified by an instruction. See the table above or ask a
service center for help.
SMS instruction texts
Default Your text Description
IMO STOP (immobilize) the vehicle (if installed)
UNIMO Unblock (mobilize) the vehicle (if installed)
STATUS GSM pager will reply with status information
GPS To obtain vehicle’s location via GPS
2
LOCATOR To obtain vehicle’s location from the GSM provider
3,4
HELP GSM pager will reply with a brief list of SMS
instructions.
CREDIT To obtain the balance of a prepaid SIM card if used
4
AUX
parameter
To operate appliances
UC xx...x
To change the user code (do this after installation).
xxx…x is the new user code, 4 to 8 characters (A –Z
& 0 – 9). The factory default user code is USER
 Only basic ASCII can be used in the SMS instruction texts.
 Ask the installer to edit the SMS commands for you.
1
If a call is activated after an alarm has been triggered and you answer the call, you will hear a siren sound
from the receiver. If a hands-free set is installed, listening to the car will be triggered.
2
CA-1803BT only
3
Only applicable if supported by the GSM provider.
4
A qualified technician is required for setting up this function.

CA-1803BT, CA-1802 User manual – mode 3 - 2 - MHF57100
.
.
.
LED indicator signals
ED indicator is used to
show the status of the
alarm.
Warning! If the LED
indicator starts flashing
fast after the ignition is
switched off, it will not
e a le to send any
messages nor call in the
case of an alarm.
LED state Meaning
OFF Ready
Permanently ON Connecting to a GSM network or a
phone call
Flashing fast GSM network is not available
Interrupted light Vehicle was stopped (immobilization)
Flashes after
turning the
ignition key on
The number of flashes corresponds
to the number of controllers enrolled.
Remote immo ilization (IMO)
When the GSM pager receives the SMS command IMO it will reply with a confirmation SMS
and block (immobilize) the engine. If the ignition key is off, the immobilization will occur
immediately. If the ignition key is on when the car alarm receives the command IMO,
immo ilization will occur as soon as the ignition key is switched off which will e
confirmed y SMS. Unblocking the car cannot be done by a key fob. It is only possi le y the
SMS instruction UNIMO.
Car location via
GPS
(CA-1803BT only)
After receiving a GPS instruction, the GSM pager will respond with the GPS coordinates of
the latest known location. If the current location is not available at the time of reception of
the instruction (as the case may be for the vehicle being in a deep-level garage), the latest
location stored in internal memory is sent. To monitor the vehicle temporarily, you can use
the GPS ON instruction which makes the GSM pager send information about location after
every 1 minute of time elapsed (limited to 15 messages).
Example of an SMS response with a GPS location:
GSM pager reports: Location: (GMT:3.12.10:35)
50*43.495N;15*11.253E;515;50, Time:3.12.05 11:35
(GMT:3.12.10:35) Greenw ch Mean T me (pr me mer d an)
50*43.495N;15*11.253E lat tude and long tude
515 alt tude (approx mated)
50 current veloc ty
T me:3.12.05 11:35 current local t me
Location via the LOCATOR service
If you use a SIM card which enables for an approximate car location via the GSM network,
you can send a LOCATOR SMS instruction to obtain the car location
3
.
Example of an SMS response sent from the GSM network:
[phone] Kraj: Jihocesky, Okres: Jindrichuv Hradec, Nazev: Nova Ves nad
Luznici Vzdalenost asi 5 4 km E14*52'1"@ N48*50'24", + -200m 15:23:01 18 09 06
Internet remote access and maintenance
The web site www.gsmlink.cz enables pager’s remote control (to users) and setting (to
installers). After a registration of the GSM pager you get a secure password protected
access. You can check the pager’s state, modify it or change settings for phone numbers
and texts. In addition, it is possible to get a listing of event records (with time, source, and
type information) as well as the vehicle motion history
3
.
When it is necessary to change the settings of the GSM pager, you mostly do not need go out for
a service. Instead, you can call and ask a service engineer to perform the setting remotely.

CA-1803BT, CA-1802 User manual – mode 3 - 3 - MHF57100
Phone calls y an installed hands free set
If the HF-03 hands free set is installed, it is possible to receive and make phone calls via the car
alarm. In addition to hands free calling, the set allows you to listen-in after an alarm has been
triggered.

Incoming calls – to answer them, press any button on the RC-8x key fob remote control
while the GSM pager is disarmed. The set allows you to receive a call from any phone
number but only when the ignition key is turned on.

To make a call – you can call up to 4 preprogrammed numbers while you are driving. By
pressing one of the buttons of the RC-8x controller you will dial the corresponding number
(preprogrammed by the installer). Each button can be assigned to a phone number.
4
 To terminate a call – press any button on the RC-8x controller.
When armed, all incoming calls are automatically rejected. If the vehicle is blocked (by the IMO instruction)
all calls are automatically answered (it is then possible to listen to and to speak to the vehicle remotely).
Additional features
Car attery low voltage reporting
The built-in voltage drop detector can trigger an alarm if an electrical device in the GSM pager is
turned on. Also the pager checks the voltage of the vehicle’s battery (the threshold limit is 10.5V).
The pager can be backed up by a BB-02 battery. Except for the acoustic siren, the BB-02 backs-
up all the functions of the car alarm. After discharging or disconnecting the main battery supply
an SMS will be sent with corresponding information.
Remote control of another appliances
If connected with another car’s appliances (e.g. independent heating), the GSM pager allows you
to operate them via the RC-8x controller or by sending an SMS instruction AUX. If you use the
RC-8x key fob for operation, press the buttons a together. If you operate via the AUX SMS
instruction see the table below for a detailed description. In addition, SMS operation allows you to
determine the requested impulse duration to activate an appliance.
Instruction Status
AUXA (B) Relay switches on for 1 second
AUXA ON (OFF)
AUXB ON (OFF)
ON – switch on permanently (ON can be replaced by 1)
OFF – switch off permanently (OFF can be replaced by 0)
Maximum switch-on (switch-off) time is 60 minutes.
AUXA xxM or xxxS
AUXB xxM or xxxS
xxM – requested duration of the relay to be switched on, in minutes
xxS – as above, in seconds
You can replace AUX w th HEATING or any other word wh ch w ll su t you.
Roaming
If you travel abroad and your SIM card supports roaming, the pager’s functionality remains
unrestricted except for the OCATOR and CREDIT functions which might be not available.
Central monitoring station communication
The car alarm allows central monitoring via GPRS data protocol. Please ask your supplier for details.
Your installer’s contact details:
Trou leshooting
Contact the company responsible for the car alarm
installation. You can also contact the manufacturer
directly.
Ja lotron s.r.o. ▪ Pod Skalkou 33 ▪ Ja lonec nad Nisou ▪ 483 559 911 ▪ www.ja lotron.cz

CA-1803BT, CA-1802 User manual – mode 3 - 4 - MHF57100
Notes: