Jabra GN9125 Flex User manual

EarthLink Business
Hosted Voice
Headset Set-up and Configuration Guide
Proprietary and Confidential

Headset Set-up and Configuration Guide
2
Proprietary and Confidential –EarthLink Business
TABLE OF CONTENTS
TABLE OF CONTENTS ....................................................................................................................................................2
JABRA GN2025 (DUAL)......................................................................................................................................................3
JABRA GN9125.....................................................................................................................................................................3
JABRA GO 6430 (SINGLE).................................................................................................................................................7

Headset Set-up and Configuration Guide
3
Proprietary and Confidential –EarthLink Business
Jabra GN2025 (Dual)
Jabra GN9125
Step 1 –Setting up
Unplug coiled handset cord from the telephone’s handset port and insert it to the bottom
of the base
Insert supplied connection cord to the telephone’s handset port and to the bottom of the
base
Connect power adapter to the socket marked (2.3) at the bottom of the base and then
connect to a power socket
The socket-outlet should be installed near the equipment and should be easily accessible
Pull out the battery security strip
Insert base into the foot by lining up the tab. Turn base until secure
For your comfort, put on the ear cushion. Place headset into the base for charging.

Headset Set-up and Configuration Guide
4
Proprietary and Confidential –EarthLink Business
Step 2 –Charging your headset
Note: The battery in the headset is not initially charged and the battery charging indicator on the
base will flash continuously during charging
To charge your headset, place the base headset into the base
The battery charging indicator on the base flashes when charging and will light when the
battery is fully charged
The battery on the headset will require a minimum of 20 minutes of charging before use.
It takes 1.5 hours before the battery is fully charged, providing up to 12 hours of talk
time.
Note: When not in use, place the headset in the base to charge the battery, ensuring the link-up
indicator is not lit. If the battery charge is too low, a beep will be heard in the headset every 20
seconds.
Step 3 –Clear dial tone
Put on the headset and lift the telephone’s handset

Headset Set-up and Configuration Guide
5
Proprietary and Confidential –EarthLink Business
If you do not hear a dial tone in the headset, move the telephone termination switch along
the A –G range until the dial tone is clear.
Step 4 –Changing wearing style from headband to earhook
Remove the ear cushion if you have it on
Hold the headband as illustrated and press the headset receiver’s speaker with your
thumb
Match the “L” or “R” inside the ear plate with the square hole on the headset. Click the
earhook on to the headset receiver.
Step 5 –Change wearing ear (L or R)
Note: The buttons on the headset must be facing upwards. Then rotate the boomarm 180
degrees, before changing “L” and “R” wearing.
For wearing headband over your left ear turn the boomarm 180 degrees.
For wearing the earhook over your left ear, align the “L” inside the earhook with the
square hole on the headset, and press the earhook onto the headset receiver. Attached
the earhook to the earhook ring’s clutch. For wearing over your right ear, do the
opposite.
Step 6 –Answering/Ending a call
Lift the telephone’s handset out of its cradle when alerted to an incoming call

Headset Set-up and Configuration Guide
6
Proprietary and Confidential –EarthLink Business
Remove the headset from the base. The link will be established and the link-up indicator
will light.
To end the call, simply lower your telephone’s handset to its cradle
Step 7 –Making/Ending a call
Remove the headset from the base. The link will be established and the link-up indicator
will light
Lift the telephone’s handset and listen for a dial tone in your headset.
Dial the desired number
To end the call, simply lower your telephone’s handset to its cradle.
Step 8 –Mute Functionality
To activate mute –press the headset’s “-“ button twice within 1 second.
To deactivate mute, again press the headset’s “-“ button twice within 1 second
Step 9 –Transmit volume adjustment
Make a telephone call and ask the person you are calling to assist you.
Press the + and –buttons on the headset at the same time momentarily, until the
headset’s on-line indicator flashes rapidly.
Adjust the volume by pressing the + or –button to reduce or increase the volume.

Headset Set-up and Configuration Guide
7
Proprietary and Confidential –EarthLink Business
When the person you are speaking with finds the volume appropriate, wait for 10 seconds,
the level is now stored.
Step 10 –Received sound volume adjustment
Make a telephone call and ask the person you are calling to assist you
Adjust the volume of received sound by pressing the + or –button. This setting is now
stored. When volume reaches max or min, you will hear a beep in headset.
Jabra GO 6430 (Single)
http://img8.jabra.com/sites/Jabra/GNImages/CCO/Documents/32-
00684_RevD_Jabra%20GO_6430_MC_OC_User%20Manual_EN_11527.pdf