JABSCO 60000 Series User manual

Model 60000-0000
60000-0024
Model 60000-Series
WIRELESS REMOTE CONTROL
FEATURES
•Adds wireless control to existing searchlight installa-
tions for both console and remote control operation.
•Can be installed for wireless-only operation.
•12/24 volt operation (60000-0000/60000-0024).
•True 8-way directional control with instant response for
precise targeting.
•“On/off”and“spot/flood”selection (for applicable models)
plus LED battery check.
•Long life lithium battery for hand-held remote control.
•Meets all applicable regulatory requirements for FCC,
Industry Canada, Australian and European compliance.
•“First-on” learning mode syncs transmitter and receiver
codes for no cross-talking with other remote control
devices.
•Up to four wireless remote units can be used per light
•Power saving "sleep mode" when not in use.
SPECIFICATIONS
Transmitter: 3VDC (CR2032 Battery)
Reverse polarity protected
433.92MHz transmitting frequency
Receiver: 12VDC or 24VDC
10 amp or 5 amp AGC Quick Blow Fuse
Input power short circuit protection
Range: 100 Ft. (30 Meters)
Temperature
Range: (-30°C to 70°C)
Regulatory
Compliance: FCC, Australia, Industry Canada and
Europe (For Radiated Emissions)
INSTALLATION
The Jabsco 60000-0000/0024 Remote adds wireless
control to new or existing Jabsco searchlight installa-
tions. It works in conjunction with a standard hard wired
Jabsco panel mount controller, thereby adding a second
controller for wireless remote operation of the search-
light at a distance of up to 100' (30 Meters). In applica-
tions where a panel mounted controller is not desired,
the 60000-0000/0024 Wireless Remote Control System
can be set up for wireless-only operation.
The Jabsco wireless receiver is installed inline between
the searchlight and the hard wired panel controller. (see
Fig. 1, 2). For installations where wireless-only operation
is preferred, the receiver's (female) connector cable is
connected to the searchlight cable.The receiver's (male)
connector cable is not connected in this instance. In
installations where the wireless remote will be used as a
second controller, (in addition to the hard wired panel
controller), the receiver's (male) connector cable is con-
nected directly to the the back of the panel controller or
to the wire pigtail coming from the back of the panel controller.
Full 8-way
Control Pad
On/Off; Spot/Flood
Switching
Grip Strip
LED Signal Transmission
Indicator (Battery Check)
WARNING
!
Disconnect battery before proceeding. Connecting
cables to the wireless receiver with power "on" to
the receiver can damage the unit.
r
!
Do not cut or trim the black receiver antenna wire
(so marked) nor connect it to battery ground (-).
r
!
CAUTION
!
Do not immerse the hand-held wireless fob in water.
r
!
CAUTION
Long Life Lithium Battery

Transmitter Cable Connectors
In instances where the pigtail from the panel controller is
not terminated with a Molex connector for connection
directly to the receiver cable, use the butt connectors
supplied to make wire to wire connections between the
controller panel and the receiver. See Fig.1, 2 below for
the wire to wire color coding. Note that the blue wire
from the receiver will, for example, connect to the blue
wire from the panel controller pigtail, the yellow to yellow, etc.
JABSCO WIRELESS RECEIVER
CONTROLLER & LIGHT CABLE WIRE COLOR CODING
Black to Controller
Brown to Controller
Green to Light
Green to Controller
Blue to Controller
Yellow to Light
Yellow to Controller
(+) Power to Battery
Black to Light
Brown to Light
Orange to Light
Orange to Controller
Blue to Light
Not Used
Not Used
(-) Ground to Battery
Mount the receiver in a suitable location using the two
screws supplied.
LEARNING MODE PROCEDURE
Note: The transmitter included with this product was ini-
tialized at the factory. It is not necessary to conduct this
procedure unless adding or replacing a transmitter.
Disconnect battery power to the receiver. Press and
hold the “on/off” transmitter button while reconnecting
power to the receiver. The searchlight will turn “on” with-
in (2) seconds. Code synchronization is complete.
The Jabsco Wireless Remote Control Sytem can sup-
port (4) separate transmitters. Each time a transmitter is
added to the system or is replaced, all transmitters
require re-initialization using the above procedure.
Power to the receiver must be disconnected then recon-
nected while pressing the transmitter’s “on/off” button for
each transmitter added in turn.
Panel
Controller Wireless
Receiver 135 Searchlight
To Wired
Controller To
Searchlight
Black to Controller
Brown to Controller
Green to Light
Green to Controller
Blue to Controller
Yellow to Light
Yellow to Controller
(+) Power to Battery
Black to Light
Brown to Light
Orange to Light
Orange to Controller
Blue to Light
Gray to Light
Gray to Controller
(-) Ground to Battery
Panel
Controller Wireless
Receiver 5” Searchlight
Fig. 2 (Lights with 43670-1003 Controller)
Fig. 1 (Lights with 60020-0000 Controller)

PARTS LIST
Part
KeyDescription Qty. Number
1 Wireless Reciever 1 1000616-01K
2 Receiver Cable Assembly 1 1000617-01K
3 Wireless Transmitter 1 1000618-01K
4 Lanyard 1 1000626-01K
OPERATING INSTRUCTIONS
With the wireless receiver installed and connected to the
searchlight cable and to the panel mounted controller (if
used), follow the following procedure.
Connect battery power to the receiver, searchlight and
hard wired panel mounted controller (if installed).
Press and hold the “on/off” button on the wireless tran-
mitter for approximately (1) second. The searchlight will
turn “on”.
Note: The red LED Signal Transmission Indicator should
be blinking while the button is depressed. If not, replace
the transmitter battery, accessed by removing the (4)
screws on the rear of the case.
With the light “on”, switching from spot to flood beam (for
5” chrome/stainless and older 7” chrome models), is
accomplished by pressing and releasing the “on/off” but-
ton quickly with no hold time. To turn the light “off”, press
and hold the “on/off” button for (1) second or until the
searchlight turns “off”.
The Jabsco 60000-0000/0024 Wireless Remote Control
features a true 8-way directional touch pad. The light’s
movement can be directed in the horizontal and vertical
simultaneously for quicker times-to-target. Searchlight
movement is instantaneous with no rotation “run-by”
when the pad is released. This provides precise pointing
control.
The wired panel controller and the wireless transmitter
share command of the light equally. Command input
from either will be executed by the searchlight.
Note: In cases when the 43670-1003 Controller toggle
switch is set to “F” for “flood” or “S” for “spot”, the beam
can still be switched using the wireless transmitter. The
wireless transmitter command will then override the
43670-1003 switch setting. In this instance the toggle
switch will indicate a flood beam, for example, when the
light is actually in spot mode, having been switched to
“spot” using the wireless transmitter. Control is returned
to the wired controller with any movement of its joystick.
The searchlight beam angle will then change to match
that indicated by the toggle switch.
When the searchlight has been turned “on” using the-
hard wired panel controller’s “on/off”toggle switch, the-
light can be turned “off”using the wireless transmitter
without the need to return to the helm station to deacti-
vate the light. Although the toggle switch then indicates
“on”, the searchlight will be “off”. With any movment of
the wired controller’s joystick the light will turn “on” and
the beam angle (spot vs.flood) will be as indicated by
the toggle switch.
CIRCUIT PROTECTION
An AGC 10 amp (for 12VDC) or 5 amp (for 24VDC) quick
blow fuse is included with the wireless receiver cable
assembly. In the event that it should be necessary to
replace the fuse, the inline fuse holder is located on the
receiver’s power lead.
1234
FCC GUIDELINES
This device complies with part 15 of the FCC Rules.
(1)This device may not cause harmful interference.
(2) This device must accept any interference received,
including interference that may cause undesired opera-
tion.
Section 15.105 Information to the user Note:This
equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference
in a residential installation. This equipment generates,
uses and can radiate radio frequencey energy and, if
not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio commu-
nications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this
equipment does causes harmful interference to radio or
television reception, which can be determined by turn-
ing the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the fol-
lowing measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and
receiver.
3. Connect the equipment into an outlet on a circuit dif
ferent from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV
technician for help.
ITT Marine and Leisure declares that this device is in
compliance with the essential requirements and
adheres to relevant provisions of Directive 1999/5/EC.

© Copyright 2007, ITT Corporation Printed in U.S.A. All Rights Reserved Form: 950-0235 Rev. C 05/2007
A. LIMITED WARRANTY:
Jabsco warrants that at the time of shipment, the products
manufactured by Jabsco and sold hereunder shall be in
conformity with applicable written specifications and descriptions
referred to or set forth herein, free from defects in material and
workmanship, merchantable, and suitable for a particular
purpose, provided such is implied by State law under the
circumstances of this sale.
B. WARRANTY ADJUSTMENT:
1. Jabsco agrees to repair or furnish a replacement for, but not to
remove or install, any product or component thereof which, within
one (1) year from date of purchase, shall upon test and
examination by Jabsco prove defective within the above warranty.
Receipt verifying purchase date is required to obtain adjustment.
2. Buyer shall notify Jabsco of any defect within this warranty no
later than ninety (90) days after the defect is discovered.
3. No product will be accepted for return or replacement without the
prior written authorization of Jabsco. Upon such authorization,
and in accordance with instructions from Jabsco, the product will
be returned to Jabsco, shipping charges prepaid by Buyer.
Products returned to Jabsco will be addressed as follows:
JABSCO
Cape Ann Industrial Park
Gloucester, MA 01930
Or to such alternate locations as may be designated
on the product, its container, or this sheet.
Repair or replacement made under this warranty
will be shipped prepaid to Buyer.
C. EXCLUSIONS FROM WARRANTY AND
LIMITATION OF LIABILITY:
1. The foregoing warranty is limited solely as set forth herein and
applies only for the period designated above.
2. ITT SHALL NOT BE LIABLE FOR ANY LOSS, DAMAGE,
SPECIAL OR CONSEQUENTIAL DAMAGE OF ANY KIND,
WHETHER BASED UPON WARRANTY, CONTRACT,
NEGLIGENCE, OR STRICT LIABILITY ARISING IN
CONNECTION WITH THE SALE, USE, OR REPAIR OF THE
PRODUCT.
3. THE MAXIMUM LIABILITY OF ITT IN CONNECTION WITH THIS
WARRANTY SHALL NOT IN ANY CASE EXCEED THE
CONTRACT PRICE FOR THE PRODUCT CLAIMED TO BE
DEFECTIVE OR UNSUITABLE.
4. This warranty does not extend to any product manufactured by
Jabsco which has been subjected to misuse, neglect, accident,
improper installation, or use in violation of instructions furnished
by Jabsco.
5. This warranty does not extend to or apply to any unit which has
been repaired or altered at any place other than Jabsco’s factory,
or by persons not expressly approved by Jabsco, nor to any unit
the serial number, model number, or identification of which has
been removed, defaced or changed.
6. Components manufactured by any supplier other than Jabsco
shall bear only that warranty made by the manufacturer of that
product.
7. This warranty applies to products defined as“consumer products”
by the Consumer Product Warranties Act as from time to time
amended.
D. CONSUMER RIGHTS:
This warranty gives you specific legal rights, and you may have
other rights which vary from state to state. Some states do not
allow exclusion or limitation of damages.
STANDARD WARRANTY:If the products manufactured and sold
hereunder are not Consumer Products, the warranty extended to
Buyer shall be as set forth in subparagraphs (A), (B), and (C), EXCEPT
THAT ALL EXPRESS OR IMPLIED WARRANTIES OR
MERCHANTABILITY OR SUITABILITY FOR ANY PARTICULAR
PURPOSE ARE EXCLUDED.
ONE YEAR LIMITED WARRANTY
UK
Jabsco
Bingley Road, Hoddesdon
Hertfordshire EN11 OBU
Tel: [phone]
Fax: [phone]
CANADA
Fluid Products Canada
55 Royal Road
Guelph, Ontario N1H 1T1
Tel: [phone]
Fax: [phone]
JAPAN
NHK Jabsco Company Ltd.
3-21-10, Shin-Yokohama
Kohoku-Ku,Yokohama, 222
Tel: [phone]
Fax: [phone]
USA
Jabsco
1 Kondelin Road
Gloucester, MA 01930
Tel: [phone]
Fax: [phone]
GERMANY
Jabsco GmbH
Oststrasse 28
22840 Norderstedt
Tel: [phone]
Fax: [phone]
ITALY
Jabsco Marine Italia S.r.l.,
ViaTomasseo, 6,
20059Vimercate, Milano
Tel: [phone]
Fax: [phone]
Warranty: All products of the company are sole and all services of the company are offered subject to the company’s warranty and terms and conditions of sale, copies of which will be furnished upon request.
The information provided herein is for guidance only, it does not constitute a guarantee of performance or specification of any individual product or component.
www.jabsco.com