Jacuzzi SALON User manual

SALON™ SPA
AIR BATH AND WHIRLPOOL
INSTALLATION AND OPERATING INSTRUCTIONS
©2006 Jacuzzi Whirlpool Bath EL21000B 10/06
Installer: Leave this manual for homeowner.
Homeowner: Read this manual and keep for future reference.
Owner's Record
Save These Instructions for Future Use.
Complete and mail-in the product registration card provided with your unit.
Write and save the model and serial number of your unit below.
Date Purchased ____________________________________________________________
Purchased From ____________________________________________________________
Installed By ________________________________________________________________
Serial Number ______________________________________________________________
Model_____________________________________________________________________

ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS
WARNING — WHEN USING THIS UNIT, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED,
INCLUDING THE FOLLOWING:
DANGER: —TO REDUCE THE RISK OF INJURY, DO NOT PERMIT CHILDREN TO USE THIS UNIT
UNLESS THEYARE CLOSELY SUPERVISED AT ALL TIMES.
WARNING — USE THIS UNITONLY FOR ITS INTENDED USEAS DESCRIBED INTHIS MANUAL. DO
NOT USEATTACHMENTS NOT RECOMMENDED BY THE MANUFACTURER.
WARNING — NEVER DROP OR INSERTANY OBJECT INTO ANY OPENING.
WARNING — DO NOT OPERATE THIS UNIT WITHOUT THE GUARD OVER THE INTAKE FOR THE
CIRCULATION PUMP (SUCTION COVER/STRAINER).
WARNING — THIS UNIT MUST BE CONNECTED ONLYTOASUPPLYCIRCUITTHATIS PROTECTED
BYAGROUNDFAULTCIRCUITINTERRUPTER(GFCI). SUCHAGFCI SHOULDBEPROVIDEDBYTHE
INSTALLERANDSHOULD BETESTEDONAROUTINE BASIS. TOTESTTHEGFCI,PUSHTHE TEST
BUTTON. THEGFCISHOULD INTERRUPTPOWER. PUSHTHERESETBUTTON. POWERSHOULD
BE RESTORED. IF THE GFCI FAILS TO OPERATE IN THIS MANNER, THE GFCI IS DEFECTIVE. IF
THEGFCI INTERRUPTS POWERTOTHEBATHTUBWITHOUTTHETESTBUTTONBEING PUSHED,
A GROUND CURRENT FLOWING, INDICATING A POSSIBILITY OFAN ELECTRIC SHOCK. DO NOT
USETHISHYDROMASSAGEBATHTUB. DISCONNECTTHEHYDROMASSAGEBATHTUBAND HAVE
THE PROBLEM CORRECTED BYA QUALIFIED SERVICE REPRESENTATIVE BEFORE USING.
WARNING — (FOR PERMANENTLY CONNECTED UNITS) A GREEN COLORED TERMINAL (OR A
WIRE CONNECTOR MARKED “G”, “GR”, “GROUND”, OR “GROUNDING”) IS PROVIDED WITHIN
THE TERMINAL COMPARTMENT. TO REDUCE THE RISK OF ELECTRIC SHOCK, CONNECT THE
TERMINAL OR CONNECTOR TO THE GROUNDING TERMINAL OF YOUR ELECTRIC SERVICE
OR SUPPLY PANEL WITH A CONDUCTOR EQUIVALENT IN SIZE TO THE CIRCUIT CONDUCTORS
SUPPLYING THIS EQUIPMENT.
OPERATING
WARNING — PROLONGED IMMERSION IN HOT WATER MAY INDUCE HYPERTHERMIA. HYPER-
THERMIA OCCURS WHEN THE INTERNAL TEMPERATURE OF THE BODY REACHES A LEVEL
SEVERALDEGREESABOVE THE NORMALBODYTEMPERATURE OF 98.6°F. THE SYMPTOMS OF
HYPERTHERMIAINCLUDEAN INCREASE IN THE INTERNALTEMPERATURE OF THE BODY, DIZZI-
NESS, LETHARGY, DROWSINESS AND FAINTING. THE EFFECTS OF HYPERTHERMIA INCLUDE:
A) FAILURE TO PERCEIVE HEAT
B) FAILURE TO RECOGNIZE THE NEED TO EXIT THE SPA OR HOT TUB,
C) UNAWARENESS OF IMPENDING HAZARD,
D) FETAL DAMAGE IN PREGNANT WOMEN,
E) PHYSICAL INABILITY TO EXIT THE SPA OR HOT TUB, AND
F) UNCONSCIOUSNESS RESULTING IN DANGER OF DROWNING.
WARNING — THE USE OF ALCOHOL, DRUGS OR MEDICATION CAN GREATLY INCREASE THE
RISK OF FATAL HYPERTHERMIA.
WARNING — DO NOT TAMPER WITH USER-OPERATED CONTROLS OR SUCH DEVICES.
2
Jacuzzi Whirlpool Bath EL21000B 10/06

ENGLISH
PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT.
The Company has obtained applicable code (standards) listings generally available on a national basis for products of this type.
It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product. The
Company makes no representation or warranty regarding, and will not be responsible for any code compliance.
NOTE: This is a professional grade product. Aknowledge of construction techniques, plumbing and electri-
cal installation according to codes are required for proper installation and user satisfaction. We recommend
that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products. Our warranty does
not cover improper installation related problems.
PRECAUTIONS
•Do not operate the hydromassage system unless the bath is filled with water to at least 1" to 2" (25,4 - 50,8 mm) above
the highest jet.
•Do not immerse the control panel by overfilling the bath.
•Do not use oil-based bath additives in your hydromassage bath.
•When cleaning your bath, do not use abrasive substances which will damage the bath's surface.
•To prevent discoloration of the acrylic finish, do not fill the bath with water in excess of 140°F (60°C).
WARNING — WHEN USING THIS UNIT, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, IN-
CLUDING THE FOLLOWING:
DANGER — RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A CIRCUIT PROTECTED BYA GROUND
FAULT CIRCUIT INTERRUPTER (GFCI).
CAUTION — TEST THE GROUND FAULT CIRCUIT INTERRUPTER PROTECTING THIS APPLIANCE PE-
RIODICALLY IN ACCORDANCE WITH MANUFACTURER’S INSTRUCTIONS.
WARNING — USE THIS UNITONLY FOR ITS INTENDED USEAS DESCRIBED IN THIS MANUAL. DO NOT
USE ATTACHMENTS NOT RECOMMENDED BY THE MANUFACTURERS.
WARNING — TO AVOID INJURY, EXERCISE CAUTION WHEN ENTERING OR EXITING THE HYDROMAS-
SAGE BATHTUB.
WARNING — KEEP BODY AND HAIR A MINIMUM OF 6" (15,2 cm) AWAY FROM SUCTION FITTING AT
ALL TIMES WHEN THE HYDROMASSAGE SYSTEM IS OPERATING. HAIR LONGER THAN SHOULDER
LENGTH SHOULD BE SECURED CLOSE TO THE HEAD.
WARNING — RISK OF ELECTRICAL SHOCK; DO NOT PERMIT ELECTRICAL APPLIANCES (SUCH AS
HAIR DRYER, LAMP, TELEPHONE, RADIO OR TELEVISION) WITHIN 60" (1,5 m) OF THIS HYDROMAS-
SAGE BATHTUB.
WARNING — RISK OF ACCIDENTAL INJURY OR DROWNING; DO NOT USE DRUGS OR ALCOHOL BE-
FORE OR DURING THE USE OF HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER TO AVOID
UNCONSCIOUSNESS AND POSSIBLE DROWNING.
WARNING — RISK OF FETAL INJURY; PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD CON-
SULT A PHYSICIAN BEFORE USING A HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER.
WARNING — RISK OF HYPERTHERMIAAND POSSIBLE DROWNING; DO NOTUSEAHYDROMASSAGE
BATHTUB EQUIPPED WITH A HEATER IMMEDIATELY FOLLOWING STRENUOUS EXERCISE.
WARNING—RISKOFHYPERTHERMIAANDPOSSIBLEDROWNING;WATERTEMPERATUREINEXCESS
OF 104°F (40°C) MAY BE INJURIOUS TO YOUR HEALTH. CHECKANDADJUST WATER TEMPERATURE
BEFORE USE.
WARNING — RISK OF HYPERTHERMIA; PEOPLE USING MEDICATIONSAND/OR HAVINGANADVERSE
MEDICAL HISTORY SHOULD CONSULT A PHYSICIAN BEFORE USING A HYDROMASSAGE BATHTUB
EQUIPPED WITH A HEATER.
FOR BUILT-IN AND DROP-IN UNITS, INSTALL TO PERMITACCESS FOR SERVICING.
THISUNITSHOULD BEELECTRICALLY GROUNDEDANDINSTALLED BYALICENSED CONTRACTOR,
ELECTRICIAN, AND PLUMBER.
BUILDING MATERIALS AND WIRING SHOULD BE ROUTED AWAY FROM THE MOTOR/PUMP OR
BLOWER OR OTHER HEAT PRODUCING COMPONENTS OF THIS UNIT.
A PRESSURE WIRE CONNECTOR IS PROVIDED ON THE EXTERIOR OF THE MOTOR/PUMP AND
HEATERTOPERMITCONNECTION OFANNO. 8AWG(8.4 mm) SOLIDCOPPERBONDINGCONDUCTOR
BETWEEN THIS UNITANDALLOTHER ELECTRIC EQUIPMENTAND EXPOSED METAL INTHE VICINITY,
AS NEEDED TO COMPLY WITH LOCAL REQUIREMENTS.
SAFETY INSTRUCTIONS - INSTALLATION
3Jacuzzi Whirlpool Bath EL21000B 10/06

ENGLISH
CONTENTS
Safety Instruction ______________________________________________________________________ 2-3
Contents _____________________________________________________________________________ 4
Specifications _________________________________________________________________________ 5-8
Roughing-in Reference __________________________________________________________________ 9-12
Framing and Support ___________________________________________________________________ 13
Service Access________________________________________________________________________ 13
Electrical Connections___________________________________________________________________ 14-15
Fuzion control Panel Installation ___________________________________________________________ 15
Plumbing and Water Supply ______________________________________________________________ 16
Fuzion Overflow Installation ______________________________________________________________ 16
Clean Up After Installation _______________________________________________________________ 16
Operating Instructions __________________________________________________________________ 17-21
Salon Control Panel __________________________________________________________________ 18-19
Salon Control Panels (for Mito™ 6) ______________________________________________________ 20
Maintenance Instructions_________________________________________________________________ 22-23
General Troubleshooting Guide____________________________________________________________ 24
Authorized Service _____________________________________________________________________ 25
Warranty _____________________________________________________________________________ 27-28
NOTE: To obtain a referral for a service agent in your area call 1-800-288-4002. You may also visit our web site at
http://www.jacuzzi.com/. To find service agent listings for:
Electrical or Mechanical Repairs visit http://jacuzzi.com/pdf/ASA.PDF
Finish, Surface, or Shell-Related Repairs visit http://jacuzzi.com/pdf/AFC.PDF
Repair Parts or Accessories visit http://jacuzzi.com/pdf/MPD.PDF
4
Jacuzzi Whirlpool Bath EL21000B 10/06

ENGLISH
SPECIFICATIONS
Important: Read complete instructions before beginning installation.
Each bath arrives ready for installation, completely equipped with blower motor, pump/motor assembly, heater, and plumbing
necessary for operation.
Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do
not lift the bath by the plumbing or wiring at any time; handle by the shell only.
Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the finish,
do not install the bath. Damage or defect to the finish claimed after the bath is installed is excluded from the warranty. Jacuzzi
Whirlpool Bath's responsibility for shipping damage ceases upon delivery of the products in good order to the carrier. Refer any
claims for damage to the carrier. For definitions of warranty coverage and limitations, refer to the published warranty information
packed with the product.
All bath units are factory tested for proper operation and watertight connections prior to shipping. NOTE: Prior to installa-
tion, the bath must be filled with water and operated to check for leaks that may have resulted from shipping damage
or mishandling. Jacuzzi Whirlpool Bath is not responsible for any defect that could have been discovered, repaired, or avoided
by following this inspection and testing procedure.
DRAIN/OVERFLOW
A
B
RECTANGULAR BATHS
5Jacuzzi Whirlpool Bath EL21000B 10/06
END VIEW
SIDE VIEW
2" (Inlet Heater)
(Motor)
(51 mm)
(Blower)
LW
H
BELLAVISTA™
END VIEW
H
W
SIDE VIEW
L1/2"
(13 mm)
(Motor)
(Inlet Heater) (Blower)
ELARA
B
A
FUZION™
DRAIN/OVERFLOW
72"
26-1/2"
2"
1"
47"
SIDE VIEW END VIEW
(51 mm)
(Inlet Heater) (Motor)
(Blower)
(25 mm
SABELLA™
END VIEW
25"
42 "
SIDE VIEW
72"
2"
(51 mm)
(Inlet Heater) (Motor) (Blower)
REÁL™
(
133 mm
)
5-1/4"
SIDE VIEWEND VIEW
70-11/16"
(Motor)
(Inlet Heater)
25-1/4"
35-3/8"
(Blower)
FUZION™ 7236 with wood SIDE VIEWEND VIEW
(Motor)
(Inlet Heater)
24"
(
102 mm
)
4"
(Blower)
70-11/16"
35-3/8"
FUZION™ 7236 undermount
6-1/4" (159 mm)
SIDE VIEWEND VIEW
(Motor)
(Inlet Heater)
72"
25-1/4"
60"
(Blower)
FUZION™ 7260 with wood
SIDE VIEWEND VIEW
(Motor)
(Inlet Heater)
72"
24"
60"
5" (127 mm)
(Blower)
FUZION™ 7260 undermount
END VIEW
SIDE VIEW
72" 2"
(51 mm)
(Heater Blank)*
42"
21-1/2"
(Blower)
(Motor)
MITO™ 6
*MITO™ 6 COMES WITH HEATER BLANK ONLY.
INLINE HEATER MUST BE PURCHASED SEPARATELY.

ENGLISH
SPECIFICATIONS (Rectangular) RH = RIGHT HAND
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR MITO™ UNIT: Electrical Service Requirements: It requires a dedicated GFCI protected separate circuit.
Blower and Motor/Pump: 120 VAC, 20 AMP, 60 Hz. dedicated GFCI protected separate circuit.
BELLAVISTA™
6
RH
BELLAVISTA™
5
RH
BELLAVISTA™
5.5
RH
72” (1829 mm) L
42” (1067 mm) W
26” ( 660 mm) H
60” (1524 mm) L
42” (1067 mm) W
26” ( 660 mm) H
66” (1676 mm) L
42” (1067 mm) W
26” ( 660 mm) H
Not Available
Not Available
180 lb
(81.8 kg)
157 lb
(71.3 kg)
85 U.S. gal
(322 liters) 177 lb (80.5 kg)
Not Available
1025 lb
(466 kg)/
59 lb/ft2
(287 kg/m2)
1186 lb
(539 kg)/
61.57 lb/ft2
(299.8 kg/m2)
1231 lb
(560 kg)/
59 lb/ft2
(228 kg/m2)
20” (508 mm) A
11-3/4” (298 mm) B
20” (508 mm) A
11-3/4” (298 mm) B
20” (508 mm) A
11-3/4” (298 mm) B
Template
Provided
P/N
P187000
Template
Provided
P/N
P187000
Template
Provided
P/N
P187000
Factory Installed
(BN60000 HEATER 230V)
MODEL PRODUCT WEIGHT
OPERATING
GALLONAGE
TOTAL WEIGHT/
FLOOR LOADINGDIMENSIONS DRAIN/OVERFLOW SKIRT & MOUNTINGCUTOUT HEATER
Factory Installed
(BN60000 HEATER 230V)
Factory Installed
(BN60000 HEATER 230V)
6
Jacuzzi Whirlpool Bath EL21000B 10/06
ELARA™ 6636
RH
ELARA™ 6042
RH
66” (1676 mm) L
36” ( 914 mm) W
26” ( 660 mm) H
60” (1524 mm) L
42” (1067 mm) W
26” ( 660 mm) H
Not Available
164 lb
(74.5 kg)
170 lb
(77 kg)
Not Available
942 lb
(428 kg)/
53.8 lb/ft2
(262 kg/m2)
847 lb
(385 kg)/
51.3 lb/ft2
(250 kg/m2)
18-1/2” (470 mm) A
9.6” (269 mm) B
18-1/2” (470 mm) A
9.6” (269 mm) B 58” x 40”
(1473 mm x 1016
mm)
Umt Template
Provided
P/N DQ50000
64” x 34”
(1626 mm x 864
mm)
Umt Template
Provided
P/N DQ51000
Factory Installed
(BN60000 HEATER 230V)
Factory Installed
(BN60000 HEATER 230V)
ELARA™ 7242
RH
72” (1829 mm) L
42” (1067 mm) W
26” ( 660 mm) H
Not Available178 lb
(81 kg)
1060 lb
(482 kg)/
50.5 lb/ft2
(246 kg/m2)
18-1/2” (470 mm) A
9.6” (269 mm) B 70” x 40”
(1778 mm x 1016
mm)
Umt Template
Provided
P/N BZ50000
Factory Installed
(BN60000 HEATER 230V)
SABELLA™
RH
REÁL™
RH
72” (1829 mm) L
47” (1194 mm) W
26-1/2” ( 673 mm) H
72” (1829 mm) L†
42” (1067 mm) W
26” ( 660 mm) H
Not Available179 lb
(81.4 kg)
Not Available
1230 lb
(559 kg)/
58.83 lb/ft2
(287 kg/m2)
1302 lb
(592 kg)/
55.3 lb/ft2
(269 kg/m2)
20 “ (508 mm) A
14 “ (356 mm) B
20 “ (508 mm) A
14” (356 mm) B 70” x 40” (1778 mm x
1016 mm)
Template
Provided
P/N
P187000
Factory Installed
(BN60000 HEATER 230V)
Factory Installed
(BN60000 HEATER 230V)
FUZION™ 7260
WITH TEAK or
WENGE
RH
FUZION™ 7236
WITH TEAK or
WENGE
RH
FUZION™ 7236
UNDERMOUNT
RH
72” (1829 mm) L
60” (1524 mm) W
25-1/4” ( 641 mm) H
70-11/16” (1795 mm) L
35-3/8” ( 899 mm) W
25-1/4” ( 641 mm) H
70-11/16” (1795 mm) L
35-3/8” ( 899 mm) W
24” ( 610 mm) H
Not Available
Not Available
Min - 145 U.S. gal
(549 liters)
Max - 192 U.S. gal
(727 liters)
274 lb
(125 kg)
Min - 70 U.S. gal
(265 liters)
Max - 94 U.S. gal
(360 liters)
200 lb
(75 kg)
Min - 70 U.S. gal
(265 liters)
Max - 94 U.S. gal
(360 liters)
165 lb
(75 kg)
Not Available
1180 lb
(536 kg)/
65.6 lb/ft2
(319 kg/m2)
1145 lb
(520.4 kg)/
63.7 lb/ft2
(310 kg/m2)
1805 lb
(820 kg)/
60 lb/ft2
(292 kg/m2)
16-3/4” (425 mm) A
12-1/16” (306 mm) B
17” (432 mm) A
10-1/4” (260 mm) B
17” (432 mm) A
10-1/4” (260 mm) B
69-1/2” x
34-3/8”
(1765 mm x
873 mm)
Template
Provided
P/N
DD42000
71” x 59”
(1803 mm x
1499 mm)
Factory Installed
(BN60000 HEATER 230V)
Factory Installed
(BN60000 HEATER 230V)
Factory Installed
(BN60000 HEATER 230V)
FUZION™ 7260
UNDERMOUNT
RH
72” (1829 mm) L
60” (1524 mm) W
24” ( 610 mm) H
Min - 145 U.S. gal
(549 liters)
Max - 192 U.S. gal
(727 liters)
199 lb
(90.5 kg) Not Available1730 lb (786 kg)/
57.6 lb/ft2
(280.5 kg/m2)
16-3/4” (425 mm) A
12-1/16” (306 mm) B Template Provided
P/N
DD44000
Factory Installed
(BN60000 HEATER 230V)
SPECIFICATIONS
90 U.S. gal
(341 liters)
80 U.S. gal
(303 liters)
Min - 75 U.S. gal
(284 liters)
Max - 83 U.S. gal
(314 liters)
Min - 83 U.S. gal
(314 liters)
Max - 92 U.S. gal
(348 liters)
Min - 95 U.S. gal
(360 liters)
Max - 105 U.S. gal
(398 liters)
98 U.S. gal
(371 liters) 184 lb
(84 kg)
MITO™ 6
RH
72” (1829 mm) L
42” (1067 mm) W
21-1/2” ( 546 mm) H
Not Available155 lb
(70.5 kg)
1197 lb
(544 kg)/
57 lb/ft2
(278 kg/m2)
17-1/2” (445 mm) A
11-7/8” (302 mm) B 70” x 40” (1778 mm x
1016 mm)
HEATER READY FOR FIELD
INSTALLATION
(S750000 HEATER 120V KIT)
Min - 62 U.S. gal
(235 liters)
Max - 90 U.S. gal
(341 liters)
Min - 62 U.S. gal
(235 liters)
Max - 90 U.S. gal
(341 liters)
†Add 1/4” (6,4 mm) to this dimension when roughing-in for 3-wall niche.
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
Blower: 120 VAC, 20 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump and RapidHeat™: 240 VAC, 20 AMP, 60 Hz. dedicated GFCI protected separate circuit.

ENGLISH
7Jacuzzi Whirlpool Bath EL21000B 10/06
SPECIFICATIONS (Oval and Round) RH = RIGHT HAND
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
Blower: 120 VAC, 20 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump and RapidHeat™: 240 VAC, 20 AMP, 60 Hz. dedicated GFCI protected separate circuit.
DUETTA™ 6636
RH
DUETTA™ 6042
RH
66” (1676 mm) L
36” ( 914 mm) W
26” ( 660 mm) H
60” (1524 mm) L
42” (1067 mm) W
26” ( 660 mm) H
Not Available
160 lb
(72.7 kg)
110 lb
(50 kg)
Not Available
999 lb
(454 kg)/
57.1 lb/ft2
(278 kg/m2)
1027 lb
(467 kg)/
62.3 lb/ft2
(303 kg/m2)
18.4” (467 mm) A
11” (279 mm) B
18.4” (467 mm) A
11” (279 mm) B Template Provided
P/N
DA09000
Template
Provided
P/N
DA08000
MODEL PRODUCT WEIGHT
OPERATING
GALLONAGE
TOTAL WEIGHT/
FLOOR LOADINGDIMENSIONS DRAIN/OVERFLOW SKIRT & MOUNTINGCUTOUT HEATER
Factory Installed
(BN60000 HEATER 230V)
Factory Installed
(BN60000 HEATER 230V)
DRAIN/OVERFLOW
A
B
OVAL AND ROUND BATHS
VENICIA™
RH
DUETTA™ 6642
RH
DUETTA™ 7242
RH
72” (1829 mm) L
42” (1067 mm) W
26” ( 660 mm) H
66” (1676 mm) L
42” (1067 mm) W
26” ( 660 mm) H
72” (1829 mm) L
42” (1067 mm) W
26” ( 660 mm) H
Not Available
Not Available
90 U.S. gal
(341 liters) 179 lb (81.4 kg)
117 lb
(53 kg)
130 lb
(59 kg)
Not Available
1106 lb
(503 kg)/
57.5 lb/ft2
(280 kg/m2)
1277 lb
(580.5 kg)/
60.8 lb/ft2
(296 kg/m2)
1230 lb
(559 kg)/
58.83 lb/ft2
(287 kg/m2)
20” (508 mm) A
14” (356 mm) B
18.4” (467 mm) A
11” (279 mm) B
18.4” (467 mm) A
11” (279 mm) B
Template
Provided
P/N
DA07000
Template
Provided
P/N
DA06000
Template
Provided
P/N
P187000
Factory Installed
(BN60000 HEATER 230V)
Factory Installed
(BN60000 HEATER 230V)
Factory Installed
(BN60000 HEATER 230V)
SPECIFICATIONS
END VIEW
H
W
SIDE VIEW
L1/2"
(13 mm)
(Motor)
(Inlet Heater) (Blower)
DUETTA
END VIEW
H
W
SIDE VIEW
2"
(Motor)
L
(51 mm)
VENICIA™
(Inlet Heater)
(Blower)
Min - 75 U.S. gal
(284 liters)
Max - 80 U.S. gal
(303 liters)
Min - 77 U.S. gal
(291 liters)
Max - 83 U.S. gal
(314 liters)
Min - 90 U.S. gal
(341 liters)
Max - 95 U.S. gal
(360 liters)
Min - 98 U.S. gal
(371 liters)
Max - 106 U.S. gal
(401 liters)

ENGLISH
8
Jacuzzi Whirlpool Bath EL21000B 10/06
SPECIFICATIONS (Corner) RH = RIGHT HAND
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4" (6,4 mm).
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
Blower: 120 VAC, 20 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump and RapidHeat™: 240 VAC, 20 AMP, 60 Hz. dedicated GFCI protected separate circuit.
FUZION™ 6666
UNDERMOUNT
RH
BELLAVISTA
CORNER
RH
FUZION™ 6666
WITH TEAK or
WENGE
RH
66” (1676 mm) L
66” (1676 mm) W
24” ( 610 mm) H
60” (1524 mm) L
60” (1524 mm) W
25” ( 635 mm) H
66” (1676 mm) L
66” (1676 mm) W
25-1/4” ( 641 mm) H
Not Available
Not Available
Min - 124 U.S. gal
(469 liters)
Max - 176 U.S. gal
(666 liters)
184 lb
(83.5 kg)
110 lb
(50 kg)
Min - 124 U.S. gal
(469 liters)
Max - 176 U.S. gal
(666 liters)
256 lb
(116.4 kg)
Not Available
1165 lb
(530 kg)/
49.6 lb/ft2
(242 kg/m2)
1923 lb
(874 kg)/
72.6 lb/ft2
(354 kg/m2)
1851 lb
(841 kg)/
69.8 lb/ft2
(340 kg/m2)
16-13/16” (427 mm) A
12-1/8” (308 mm) B
18-7/8” (479 mm) A
14” (356 mm) B
16-13/16” (427 mm) A
12-1/8” (308 mm) B
Template
Provided
P/N
P654000
See
Page 12
Template
Provided
P/N
DD43000
Factory Installed
(BN60000 HEATER 230V)
MODEL PRODUCT WEIGHT
OPERATING
GALLONAGE
TOTAL WEIGHT/
FLOOR LOADINGDIMENSIONS DRAIN/OVERFLOW SKIRT & MOUNTINGCUTOUT HEATER
Factory Installed
(BN60000 HEATER 230V)
Factory Installed
(BN60000 HEATER 230V)
CORNER BATHS
SPECIFICATIONS
(159 mm)
6-1/4"
SIDE VIEWEND VIEW DRAIN/OVERFLOW
B
A
(Intake Heater) (Motor)
25-1/4"
66"
66"
(Blower)
FUZION™ 6666 with wood
25"
SIDE VIEW
A
B
DRAIN/OVERFLOW
(Inlet Heater)
(Motor)
(Blower)
60"
END VIEW
2”
(51 mm)
BELLAVISTA™ CORNER
SIDE VIEWEND VIEW DRAIN/OVERFLOW
B
A
(Inlet Heater) (Motor)
24"
66"
(
127 mm
)
5"
66"
(Blower)
FUZION™ 6666 undermount
Min - 77 U.S. gal
(291 liters)
Max - 83 U.S. gal
(314 liters)

ENGLISH
9Jacuzzi Whirlpool Bath EL21000B 10/06
ROUGHING-IN REFERENCE
NOTE: 1. THE OVERALL DIMENSIONSARE NOMINAL WITHATOLERANCE OF +0AND -1/4" (6,4 mm).
2. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
3. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
4. Service Access dimensions given are minimum size.
7" 32-1/2"
11-3/4"
6"
30-1/8"
42"
60"
4" x 4" Motor
12" H x 24" L
Service Access
Heater
Blower
Bellavista™ 5,
(Right Hand Only)
10" 35-1/2"
11-3/4"
6"
30-1/8"
42"
66"
4" x 4" Motor
12" H x 24" L
Service Access
Heater
Blower
Bellavista™ 5.5
(Right Hand Only)
4" x 4"*
42"
72"
10-1/2" 35-13/16"
11-3/4"
6"
30-1/8"
Motor
12" H x 24" L
Service Access
Heater
Blower
Bellavista™ 6
(Right Hand Only)
36"
42"
72"
11-7/8"
10" x 4"
2"
Motor
12" H x 24" L
Service Access
5-3/8"
Blower
Heater Blank*
MITO™ 6,
(Right hand only)
*MITO™ 6 COMES WITH HEATER BLANK ONLY.
INLINE HEATER MUST BE PURCHASED SEPARATELY.
60"
42"
21"
4.2"
9.6"
12" x 4"
2"
Heater
Motor
Opt. Service
Access
12" H x 24" L
Service Access
Blower
Elara™ 6042,
Right Hand
Elara™ 6636,
Right Hand
66"
36"
18 "
4.2"
9.6"
12" x 4"
Motor
Opt. Service
Access
12" H x 24" L
Service Access
Heater
2"
Blower
Some tubs are supplied with cutout template and/or undermount template. Refer to CUTOUT on pages 6-8 for template part
numbers.
72"
42"
21"
4.2"
9.6"
12" x 4"
2"
Heater
Motor
Opt. Service
Access
12" H x 24" L
Service Access
Blower
Elara™ 7242,
Right Hand

ENGLISH
10
Jacuzzi Whirlpool Bath EL21000B 10/06
ROUGHING-IN REFERENCE
NOTE: 1. THE OVERALL DIMENSIONSARE NOMINAL WITHATOLERANCE OF +0AND -1/4" (6,4 mm).
2. Measurements inside each unit represent cutout in floor to allow for drain/overflow.
3. All measurements are in inches. To convert to millimeters, multiply inches by 25.4.
4. Service Access dimensions given are minimum size.
Motor
Opt. Service Access
17-11/16''
2'' 7''
10-1/4''
12'' x 4"*
Heater
70-11/16''
35-3/8''
12" H x 24" L
Service Access
Blower
Fuzion™ 7236, Right Hand
Opt. Service Access
17-11/16''
2'' 7''
10-1/4''
12'' x 4"*
Heater
70-11/16''
35-3/8'' Motor
12" H x 24" L
Service Access
Blower
Fuzion™ 7236 Undermount,
Right Hand
Some tubs are supplied with cutout template and/or undermount template. Refer to CUTOUT on pages 6-8 for template part
numbers.
Motor
Heater
72"
60"
36"
24.19"
12"
8.47"
18-1/2" x 4"
12" H x 24" L
Service Access
Optional
Service Access
Blower
Fuzion™ 7260,
Right Hand
Motor
Heater
72"
60"
36"
24.19"
12"
8.47"
18-1/2" x 4"
12" H x 24" L
Service Access
Optional
Service Access
Fuzion™ 7260 Undermount,
Right Hand
Blower
10-1/2"
36"
14"
5-1/4"
42"
72"
3"
Motor
12" H x 24" L Service Access
Heater
Blower
18" x 4"*
REÁL™
Right Hand
72"
10-1/4" 36"
3"
1"
3"
3"
1"
7"
47"
13-3/4"
18" x 4" Motor
12" H x 24" L Service Access
Heater
Blower
Sabella™
Right Hand