Jadeim Handy 10740 User manual

AIR LIFT
INSTRUCTIONS l PARTS DRAWING l PARTS LIST
WARNING: READ INSTRUCTIONS BEFORE OPERATING
1. Center load on table - 1000 lb. maximum.
2. Connect to 100 psi maximum shop air.
3. Keep safety bar in position at all times - except
when lowering.
4. Keep hands and tools from under carriage.
5. Do not mount table when in elevated position.
6. Do not ride vehicle onto lift.
7. Lift must be in the lowered position when moving.
8. Only trained persons should operate Air Lift.
9. The working area should be sufficiently lit.
10. Foot controller should be at least 3 feet away from
Air Lift during raising and lowering operation.
11. Recommended for indoor use only.
HANDY INDUSTRIES DIVISION OF JADEIM, LLC 401 South 2nd. Marshalltown, IA 50158
1-800-247-7594 Fax [phone] www.handyindustries.com
Part Numbers 10740 - 16749 - 16600
LIFT TABLE
DETENT BAR
FOOT VALVE
RAMP
SAFETY LATCH

AIR LIFT
NOTE: READ ENTIRE MANUAL TO COMPLY WITH ALL SAFETY AND SERVICE PRECAUTIONS. DEATH, PERSONAL
INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY.
INSTRUCTIONS
UNPACKING AND SET-UP
1. Open carton, then remove ramp, and shipping boards.
2. CAREFULLY TURN TABLE UPRIGHT INTO OPERATING POSTION BEFORE REMOVING SHIPPING
CABLE RESTRAINT FROM SCISSOR MECHANISM.
3. Connect foot-operated air valve to 100 psi air supply. The lift may be damaged and/or personal injury may
result if the pressure exceeds the maximum 100 psi rating.
4. Stand clear of lift table and depress the UP side of foot valve to raise table.
5. To lower table, lift detent bar from safety latch and lower to next position or to floor.
6. Insert ramp mounting pins into holes at either end of table to mount ramp.
NOTE: If cycle vise is being installed, ramp must be mounted opposite the cycle vise.
OPERATION
1. Loads must be centered on table at all times.
2. Loads must be firmly positioned and secured on table at all times.
3. All moving parts have been lubricated at the factory and should be re-lubricated every 6 months to prevent
galling. Grease zerks are located at each end of frame pivot shaft and at top ends of inside frame assembly.
4. Lightly oil cylinder rod when it becomes dry.
5. Squirt some oil through air bleed hole in plate end of cylinder to lubricate piston and its seal every
6 months.
6. Pivot shaft set screws should be checked frequently to be sure they are tight. These are located at the top
end of the inside frame assembly.
OTHER OPTIONS AVAILABLE
Separate installation instructions included with each option.
PART #
DESCRIPTION
14476
CV-17 CYCLE VISE – Vise with removable wheel stop built into vise
10730
8” SIDE EXTENSIONS (2) – Expands width of lift from 24” to 40”
10728
12” SIDE EXTENSIONS (2) – Expands width of lift from 24” to 48” includes stabilizer bar
16011
13” FRONT EXTENSIONS – Extends lift top to 93” for longer wheel base motorcycles
15566
RAMP END EXTENSION – Attaches to end of lift ramp for a more gradual incline to prevent bigger
bikes from dragging bottom.
10737
SNOWMOBILE WING KIT – Used when lifting snowmobiles
14169
TRIKE EXTENSION – Used for 3 wheeled vehicles
16355
CE FOOT PEDAL – Covered foot pedal
10732
LIFT DOLLY – Helps move lift while in down position
15833
RED HANDY TIE-DOWNS – 1 pair – Secure your equipment on our lift with 1” x 6’ straps
16010
TOOL TRAY – Keeps tools organized and Handy

PART NO.
DESCRIPTION
QTY/UNIT
PART NO.
DESCRIPTION
QTY/UNIT
10819
Detent Clip
1
11250
Screw ¾-10 x 1¾
1
11008
Frame/Cylinder Pivot Shaft
1
11251
½ -13 Hex Nut
4
11052
Top Assembly
1
11252
Cam Bearing Retaining Ring
2
11167
Cylinder Assy & End Plate (Gray)
1
11253
Wheel Retaining Ring
4
11071
Cylinder Shaft Assembly (Gray)
1
11254
Frame Shaft Retaining Ring
2
14381
Valve Hose w/fittings
1
11255
Lock washer - ¾”
1
11123
Ramp Assembly (Gray)
1
11304
Cylinder Shaft Bushing
1
12937
Foot Valve Assembly (complete)
1
11305
Cylinder Shaft Seal
1
12887
Valve Stem Assembly
1
11306
Piston Seal
1
11177
Detent Bar
1
11308
Piston
1
11179
Frame Pivot Shaft
1
11315
Cam Roller Bearing
4
11183
Cylinder Repair Kit
1
11316
Cam Bearing Spacer
2
11248
½ x 1¾ Clevis Pin
2
11319
Cast Wheel
2
11249
1/8 x 7/8 Cotter Pin
2
11321
Track Roller Bearing
2
REPLACEMENT PARTS

09/10 14382
HANDY LIMITED WARRANTY
Handy Industries Division of Jadeim LLC, warrants to the original purchaser of this product, all parts to be free from defects in manu-
facture for a period of one (1) year from date of delivery. Notice of a defective part must be received in writing at Handy Industries with-
in one (1) year of purchase. All defective parts must be returned to Handy Industries and which, upon our examination any parts which
are defective in manufacture or workmanship, will be replaced or put in good operating condition. This warranty does not apply to dam-
age resulting from accident, improper installation, repair, operation or maintenance, negligence or neglect. THE COST OF SUCH
REPLACEMENT OR REPAIR SHALL BE EXCLUSIVE REMEDY FOR ANY BREACH OF ANY WARRANTY AND HANDY
INDUSTRIES SHALL NOT BE LIABLE TO ANY PERSON FOR CONSEQUENTIAL DAMAGE, OR INJURY, OR COMMERCIAL LOSS
RESULTING FROM ANY BREACH OF WARRANTY. HANDY INDUSTRIES MAKES NO WARRANTY OR MERCHANTABILITY,
MAKES NO WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND MAKES NO OTHER WARRANTY EXPRESSED OR
IMPLIED, INCLUDING IMPLIED WARRANTY ARISING FROM THE COURSE OR DEALING OR USAGE OF THE TRADE.