Jadeim Handy B.O.B. 1500 AIR LIFT User manual

B.O.B. 1500 AIR LIFT
INSTRUCTIONS l PARTS DRAWING l PARTS LIST
PART NUMBERS: 14472 - 16759 - 17008
WARNING: READ INSTRUCTIONS BEFORE OPERATING
1. Center load on table - 1500 lb.maximum.
2. Connect to 100 psi maximum shop air.
3. Keep safety bar in position at all times - except
when lowering.
4. Keep hands and tools from under carriage.
5. Do not mount table when in elevated position.
6. Do not ride vehicle onto lift.
7. Lift must be in the lowered position when moving.
8. Only trained persons should operate Air Lift.
9.The working area should be sufficiently lit.
10. Foot controller should be at least 3 feet away from
Air Lift during raising and lowering operation.
11. Recommended for indoor use only.
HANDY DIVISION OF JADEIM, LLC
401 South 2nd. Marshalltown, IA 50158 Ph: 855-752-5446 Fax [phone] www.handyindustries.com

B.O.B. 1500 AIR LIFT
NOTE: READ ENTIRE MANUAL TO COMPLY WITH ALL SAFETY AND SERVICE PRECAUTIONS.
DEATH, PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS
ARE FOLLOWED CAREFULLY.
INSTRUCTIONS
UNPACKING AND SET-UP
1. Open carton, the n remove ramp and shipping boards.
2. Connect foot-operated air valve to 100 psi maximum air supply. The lift may be damaged
and/or personal injury may result if the pressure exceeds the maximum 100 psi rating.
3. Stand clear of lift table, and depress the UP side of foot valve to raise table.
4. To lower table, lift detent bar from safety latch and lower to next position or to floor.
5. To mount ramp, insert ramp mounting pins into holes at end of table opposite vise holes.
OPERATION
1. Loads must be centered on table at all times. Table is rated for a maximum load of 1500 lbs.
2. Loads must be firmly positioned and secured on table at all times.
3. All moving parts have been lubricated at the factory and should be re-lubricated every (6)
months to prevent galling. Grease zerks are located at each end of frame pivot shaft and at
top ends of inside frame assembly.
4. Lightly oil cylinder rod when it becomes dry.
5. Squirt some oil through bleed hole in plate end of cylinder to lubricate piston and its seal every
(6) months.
6. Pivot shaft set screws should be checked frequently to be sure they are tight. These are
located at the top end of the inside frame assembly.
OTHER OPTIONS AVAILABLE
Separate installation instructions included with each option.
PART#
DESCRIPTION
14476
CV-17 CYCLE VISE- Used to stablize motorcycles while on lift.
14473
12” SIDE EXTENSION (2) - Expands width of lift from 28” to 52” includes stabilizer bar.
14474
13” FRONT EXTENSION - Extends lift top to 97” for longer wheel base motorcycles.
14475
TRIKE EXTENSION - Used for 3 wheeled vehicles.

B.O.B. 1500 AIR LIFT
PARTS DRAWING - PARTS LIST
Part # Description
10819 detent clip
11086 valve hose w/fitting
11250 screw 3/4 -10 x 1-3/4
11253 retaining ring 1-5/16
11255 lockwasher - 3/4”
11319 wheel
12887 valve stem assembly
12937 foot valve assembly complete
11304 cylinder shaft bushing
11305 cylinder shaft seal
15379 cylinder assembly
15390 cylinder shaft assembly
15397 cam roller bearing
15400 retaining ring 2-3/8”
15401 piston
15403 piston seal
Part# Description
15607 top assembly
15411 inside frame assembly
15431 outside frame assembly
15446 foot assembly
15452 ramp
15687 drop out cover
15458 detent bar
15460 frame pivot shaft
15461 cylinder pivot shaft
15462 retaining ring 1-1/4”
15463 track roller bearing
15484 cover plate
15528 rubber pad
15529 spacer
15567 ramp end extension
15687
11304
11305

15489 09/10
HANDY LIMITED WARRANTY
Handy Industries Division of Jadeim LLC, warrants to the original purchaser of this product, all parts to be free from defects in manufacture for
a period of one (1) year from date of delivery. Notice of a defective part must be received in writing at Handy Industries within one (1) year of
purchase. All defective parts must be returned to Handy Industries and which, upon our examination any parts which are defective in manu-
facture or workmanship, will be replaced or put in good operating condition. This warranty does not apply to damage resulting from accident,
improper installation, repair, operation or maintenance, negligence or neglect. THE COST OF SUCH REPLACEMENT OR REPAIR SHALL BE
EXCLUSIVE REMEDY FOR ANY BREACH OF ANY WARRANTY AND HANDY INDUSTRIES SHALL NOT BE LIABLE TO ANY PERSON FOR
CONSEQUENTIAL DAMAGE, OR INJURY, OR COMMERCIAL LOSS RESULTING FROM ANY BREACH OF WARRANTY. HANDY
INDUSTRIES MAKES NO WARRANTY OR MERCHANTABILITY, MAKES NO WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE
AND MAKES NO OTHER WARRANTY EXPRESSED OR IMPLIED, INCLUDING IMPLIED WARRANTY ARISING FROM THE COURSE OR
DEALING OR USAGE OF THE TRADE.