Jai El-2800m-cxp User manual

1048E-1305

Elite Series

EL-2800M-CXP

EL-2800C-CXP

2.8M Digital Progressive Scan

Monochrome and Color Camera

Document Version:1.4

EL-2800-CXP_Ver.1.4_Mar2014

User Manual

EL-2800M-CXP / EL-2800C-CXP

- 2 -

Notice

The material contained in this manual consists of information that is proprietary to JAI Ltd., Japan

and may only be used by the purchasers of the product. JAI Ltd., Japan makes no warranty for the

use of its product and assumes no responsibility for any errors which may appear or for damages

resulting from the use of the information contained herein. JAI Ltd., Japan reserves the right to

make changes without notice.

Company and product names mentioned in this manual are trademarks or registered trademarks of

their respective owners.

Warranty

For information about the warranty, please contact your factory representative.

Certifications

CE compliance

As defined by the Directive 2004/108/EC of the European Parliament and of the Council, EMC

(Electromagnetic compatibility), JAI Ltd., Japan declares that EL-2800M-CXP and EL-2800C-CXP

comply with the following provisions applying to its standards.

EN 61000-6-3 (Generic emission standard part 1)

EN 61000-6-2 (Generic immunity standard part 1)

FCC

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-Consult the dealer or an experienced radio/TV technician for help.

Warning

Changes or modifications to this unit not expressly approved by the party

responsible for FCC compliance could void the user’s authority to operate the

equipment.

EL-2800M-CXP

Supplement

The following statement is related to the regulation on “ Measures for the Administration

of the control of Pollution by Electronic Information Products “ , known as “ China RoHS “.

The table shows contained Hazardous Substances in this camera.

mark shows that the environment-friendly use period of contained Hazardous

Substances is 15 years.

嶷勣廣吭並㍻

嗤蕎嗤墾麗嵎賜圷殆兆各式根楚燕

功象嶄鯖繁酎慌才忽佚連恢匍何〆窮徨佚連恢瞳麟半陣崙砿尖一隈〇



云恢瞳ゞ嗤蕎



嗤

墾麗嵎賜圷殆兆各式根楚燕〃泌和



桟隠聞喘豚㍉

窮徨佚連恢瞳嶄根嗤議嗤蕎嗤墾麗嵎賜圷殆壓屎械聞喘議訳周和音氏窟伏翌

亶賜融延、窮徨佚連恢瞳喘薩聞喘乎窮徨佚連恢瞳音氏斤桟廠夛撹冢嶷麟半

賜斤児繁附、夏恢夛撹冢嶷鱒墾議豚㍉。

方忖仝15々葎豚㍉15定。

EL-2800C-CXP

Supplement

The following statement is related to the regulation on “ Measures for the Administration

of the control of Pollution by Electronic Information Products “ , known as “ China RoHS “.

The table shows contained Hazardous Substances in this camera.

mark shows that the environment-friendly use period of contained Hazardous

Substances is 15 years.

嶷勣廣吭並㍻

嗤蕎嗤墾麗嵎賜圷殆兆各式根楚燕

功象嶄鯖繁酎慌才忽佚連恢匍何〆窮徨佚連恢瞳麟半陣崙砿尖一隈〇



云恢瞳ゞ嗤蕎



嗤

墾麗嵎賜圷殆兆各式根楚燕〃泌和



桟隠聞喘豚㍉

窮徨佚連恢瞳嶄根嗤議嗤蕎嗤墾麗嵎賜圷殆壓屎械聞喘議訳周和音氏窟伏翌

亶賜融延、窮徨佚連恢瞳喘薩聞喘乎窮徨佚連恢瞳音氏斤桟廠夛撹冢嶷麟半

賜斤児繁附、夏恢夛撹冢嶷鱒墾議豚㍉。

方忖仝15々葎豚㍉15定。

EL-2800M-CXP / EL-2800C-CXP

- 3 -

- Contents -

Introduction ....................................................................................- 6 -

1. General ....................................................................................- 7 -

2. Camera composition ...................................................................- 7 -

3. Main features............................................................................- 8 -

4. Locations and functions ...............................................................- 9 -

4.1 Locations and functions ............................................................................- 9 -

4.2 Rear panel .......................................................................................... - 10 -

5. Input and output ......................................................................... - 11 -

5.1 CoaXPress interface standard.................................................................... - 11 -

5.2 Connectors and pin assignment ................................................................. - 12 -

5.2.1 Digital Video Output (75Ω 1.0/2.3 DIN Receptacle) .................................. - 12 -

5.2.2 12-Pin connector.............................................................................. - 12 -

5.2.2.1 Pin assignment ........................................................................... - 12 -

5.2.3 AUX Standard Hirose 10-Pin connector for Lens ......................................... - 12 -

5.2.4 AUX Type 2 HIROSE 10-Pin connector (Factory option).............................. - 13 -

5.2.5 AUX Type 3 HIROSE 10-Pin connector (Factory option).............................. - 13 -

5.3 Output............................................................................................... - 14 -

5.3.1 Digital output ................................................................................. - 14 -

5.3.1.1 Output level.............................................................................. - 14 -

5.4 Digital IN/OUT interface ......................................................................... - 14 -

5.4.1 Line Selector .................................................................................. - 14 -

5.4.2 Line source .................................................................................... - 15 -

5.4.3 Line Mode...................................................................................... - 15 -

5.4.4 Line Inverter .................................................................................. - 15 -

5.4.5 Line Status..................................................................................... - 15 -

5.4.6 Line Format ................................................................................... - 15 -

5.4.7 GPIO ............................................................................................ - 15 -

5.4.7.1 GPIO block diagram ..................................................................... - 16 -

5.4.7.2 IN and OUT matrix table.............................................................. - 17 -

5.5 Pulse Generator.................................................................................... - 18 -

5.5.1 Clock Pre-scaler .............................................................................. - 18 -

5.5.2 Pulse Generator Selector.................................................................... - 18 -

5.5.3 Pulse Generator Length ..................................................................... - 19 -

5.5.4 Pulse Generator Start Point................................................................. - 19 -

5.5.5 Pulse Generator End Point .................................................................. - 19 -

5.5.6 Pulse Generator Repeat Count ............................................................. - 19 -

5.5.7 Pulse Generator Clear Activation .......................................................... - 19 -

5.5.8 Pulse Generator Clear Sync Mode.......................................................... - 19 -

5.5.9 Pulse Generator Clear Source .............................................................. - 21 -

5.5.10 Pulse Generator Inverter .................................................................. - 22 -

5.5.11 Pulse Generator Setting table ............................................................ - 22 -

6. Sensor layout, output format and timing ........................................ - 23 -

6.1 Sensor layout ....................................................................................... - 23 -

6.1.1 Monochrome sensor .......................................................................... - 23 -

6.1.2 Bayer color sensor .......................................................................... - 23 -

6.2. Sensor readout (Sensor Tap Geometry) ....................................................... - 24 -

6.2.1 4 taps readout (1X2–2YE).................................................................... - 24 -

6.2.2 2 Taps readout (2XE–1Y) ..................................................................... - 24 -

6.2.3 1 tap readout (1X–1Y)........................................................................ - 24 -

6.3. Camera output format and sensor readout system ......................................... - 25 -

EL-2800M-CXP / EL-2800C-CXP

- 4 -

6.3.1 1X-1Y ........................................................................................... - 25 -

6.3.2 1X–2YE ......................................................................................... - 25 -

6.4 The relations between tap Geometry and Frame rate ...................................... - 26 -

6.5 Output timing ...................................................................................... - 26 -

6.5.1 Horizontal timing............................................................................. - 26 -

6.5.1.1 Output format 1X–2YE (Pixel clock: 108 MHz)................................... - 26 -

6.5.1.2 Output format 1X–2YE (Pixel clock: 108 MHz)................................... - 27 -

6.5.2.1 Output format 1X–1Y (Camera Output Pixel clock: 108 MHz)................. - 27 -

6.5.2.2 Output format 1X–1Y (Camera Output Pixel clock: 108 MHz)................. - 27 -

6.5.2 Vertical timing................................................................................ - 28 -

6.5.2.1 Output format 1X–2YE Vertical binning OFF.................................. - 28 -

6.5.2.2 Output format 1X–2YE Vertical binning ON ................................. - 28 -

6.5.2.3 Output format 1X–1Y Vertical Binning OFF ................................... - 28 -

6.5.2.4 Output format 1X–1Y Vertical Binning ON .................................... - 28 -

7. Operating modes......................................................................- 29 -

7.1. Acquisition control (change the frame rate)................................................. - 29 -

7.1.1 Acqusition mode.............................................................................. - 29 -

7.1.1.1 Single Frame ............................................................................. - 29 -

7.1.1.2 MultiFrame ............................................................................... - 33 -

7.1.1.3 Continuous mode........................................................................ - 37 -

7.1.2 Acquisition frame count..................................................................... - 39 -

7.1.3 Acquisition frame rate ...................................................................... - 40 -

7.1.4 Calculation of frame rate................................................................... - 40 -

7.1.4.1 V Binning Off............................................................................. - 40 -

7.1.4.2 V Binning On ............................................................................. - 40 -

7.2. Exposure setting.................................................................................. - 41 -

7.2.1 Exposure Mode................................................................................ - 41 -

7.2.2 Exposure Time ................................................................................ - 41 -

7.2.3 Exposure Auto................................................................................. - 42 -

7.3. Trigger Mode ...................................................................................... - 42 -

7.3.1 Trigger Source ................................................................................ - 42 -

7.3.2 Trigger activation ............................................................................ - 42 -

7.3.3 Trigger Overlap ............................................................................... - 42 -

7.3.4 Trigger Delay .................................................................................. - 43 -

7.4. Normal continuous operation (Timed Exposure Mode/Trigger Mode OFF)............... - 43 -

7.5. Timed mode (EPS)................................................................................ - 43 -

7.5.1 If the overlap setting is “OFF” ............................................................. - 44 -

7.5.2 If the overlap setting is “Readout”........................................................ - 44 -

7.6. Trigger width mode .............................................................................. - 45 -

7.6.1 If the overlap setting is “OFF” ............................................................. - 45 -

7.6.2 If the overlap setting is “Readout”........................................................ - 46 -

7.7. RCT mode.......................................................................................... - 47 -

7.8. PIV (Particle Image Velocimetry) .............................................................. - 48 -

7.9. Sequential Timed Exposure Mode.............................................................. - 49 -

7.9.1 Video send mode ............................................................................. - 49 -

7.9.2 Sequence ROI setting parameters ......................................................... - 50 -

7.10. Operation and function matrix ............................................................... - 52 -

8. Other functions .......................................................................- 53 -

8.1 Black level control ................................................................................ - 53 -

8.1.1 Black Level Selector ......................................................................... - 53 -

8.1.2 Black Level .................................................................................... - 53 -

8.1.3 Black Level Auto.............................................................................. - 53 -

8.2 Gain control ........................................................................................ - 54 -

EL-2800M-CXP / EL-2800C-CXP

- 5 -

8.2.1 Gain Selector.................................................................................. - 54 -

8.2.2 Gain............................................................................................. - 55 -

8.2.3 Gain Raw....................................................................................... - 55 -

8.2.4 Gain Auto ...................................................................................... - 56 -

8.2.5 Balance White Auto .......................................................................... - 56 -

8.3. LUT.................................................................................................. - 56 -

8.3.1 LUT Enable .................................................................................... - 56 -

8.3.2 LUT Index ...................................................................................... - 57 -

8.3.3 LUT value ...................................................................................... - 57 -

8.4. Gamma ............................................................................................. - 57 -

8.5. Shading Correction ............................................................................... - 57 -

8.6. Blemish compensation ........................................................................... - 59 -

8.7. Bayer color interpolation (Only for EL-2800C) ............................................... - 59 -

8.8 Lens .................................................................................................. - 60 -

8.8.1 About P-Iris .................................................................................... - 60 -

8.8.2 Setting for P-iris lens being used .......................................................... - 60 -

8.8.2.1 P-Iris lens select ......................................................................... - 61 -

8.8.2.2 Step max.................................................................................. - 61 -

8.8.2.3 Position ................................................................................... - 61 -

8.8.2.4 Current F value .......................................................................... - 61 -

8.8.2.5 P-Iris Auto min. / P-Iris Auto max. ................................................... - 61 -

8.8.2.6 Auto Iris Lens Control Signal Output ................................................. - 61 -

8.8.3 Motorized lenses ............................................................................ - 61 -

8.8.3.1 Iris ......................................................................................... - 61 -

8.8.3.2 Zoom ...................................................................................... - 62 -

8.8.3.3 Focus+..................................................................................... - 62 -

8.8.4 Exclusive video output signal for iris control.............................................. - 62 -

8.8 ALC................................................................................................... - 63 -

9. Camera setting ......................................................................... - 64 -

10. External appearance and dimensions ......................................... - 65 -

11. Specifications........................................................................ - 66 -

11.1 Spectral response ................................................................................ - 66 -

11.2 Specifications table.............................................................................. - 67 -

Appendix...................................................................................... - 70 -

1. Precautions ............................................................................................ - 70 -

2. Typical Sensor Characteristics...................................................................... - 70 -

3. Caution when mounting a lens on the camera................................................... - 70 -

4. Caution when mounting the camera .............................................................. - 70 -

5. Exportation ............................................................................................ - 71 -

6. References............................................................................................. - 71 -

Manual change history ..................................................................... - 72 -

User's Record ................................................................................ - 73 -

EL-2800M-CXP / EL-2800C-CXP

- 6 -

Introduction

Interface

The EL-2800M-CXP and EL-2800C-CXP employ CoaXPress as an interface system. In order to connect

the camera to a PC, it requires the use of a Frame Graber board and the appropriate coaxial

cable(s). The maximum video transfer rate per coaxial cable is 6.25 Gbps (CXP-6). The maximum

rate per cable supported by the EL-2800 is 3.125 Gbps (CXP-3) but for RGB output, 6.25 Gbps is

supported. In addition to video information, power and control signals can be transferred to the

camera over this interface. For detailed specifications, please refer to “JIIA-NTF-001-2010”

published by Japan Industrial Imaging Association, http://www.jiia.org.

Frame grabber boards used with EL-2800 series

As the EL-2800M-CXP and EL-2800C-CXP employ CoaXPress as an interface system, a

CoaXPress-compliant frame grabber board is required. Each camera has a single CoaXPress

interface connector.

Cables used with EL-2800 series

For the CoaXPress interface, coaxial cables are used. In the EL-2800M-CXP and EL-2800C-CXP, they

use 75Ω1.0/2.3 DIN receptacles (Amphenol ACX1785-ND or equivalent). The coaxial cable used to

connect the camera must have a 75Ω1.0/2.3 DIN-type plug at the camera side. An ordinary BNC

cable cannot be used.

EL-2800M-CXP / EL-2800C-CXP

- 7 -

1. General

The EL-2800M-CXP and EL-2800C-CXP are new cameras in JAI’s Elite Series. They provide high

picture quality, such as high sensitivity and low noise, suitable for machine vision applications. The

EL-2800M-CXP is a monochrome progressive scan CCD camera and the EL-2800C-CXP is the

equivalent Bayer mosaic progressive scan CCD camera. Both are equipped with a 2/3 inch CCD

sensor offering 2.83 million pixels resolution and a 4:3 aspect ratio. They provide 54.7 frames per

second for continuous scanning with 1920 x 1440 full pixel resolution for both monochrome and raw

Bayer output.

8-bit, 10-bit, or 12-bit output can be selected for both monochrome and Bayer outputs. The

EL-2800C-CXP is also capable of performing in-camera color interpolation to produce 24-bit (8-bit

per color) RGB output at 54.7 in Quad Tap Sensor Geometry. The new cameras feature a CoaXPress

interface which uses coax cable with the capability of supplying power through the cable. The

EL-2800M-CXP and EL-2800C-CXP use a single coaxial cable interface. A full pixel readout, partial

scan readout, or binning mode (monochrome only) can be selected depending on the application.

EL-2800M-CXP and EL-2800C-CXP have various comprehensive functions needed for automated

optical inspection applications, such as solid state device inspection or material surface inspection.

They incorporate video processing functions such as a look-up table, shading compensation, and

blemish compensation in addition to fundamental functions such as trigger, exposure setting and

video level control.

As a common Elite Series feature, a new connector for lens control is employed. EL-2800M-CXP and

EL-2800C-CXP support P-iris and motor-driven lenses as standard lens control capabilities. Factory

options are available to configure this connector to support DC iris systems as well as provide a

video iris output signal, or to provide additional TTL IN and OUT lines.

The latest version of this manual can be downloaded from: www.jai.com

The latest version of the Camera Control Tool for the EL-2800M-CXP and EL-2800C-CXP can be

downloaded from: www.jai.com

For camera revision history, please contact your local JAI distributor.

2. Camera composition

The standard camera composition is as follows.

Camera body 1

Sensor protection cap 1

Dear Customer (sheet) 1

The following optional accessories are available.

Tripod base

MP-42

Power supply unit

PD-12 series

EL-2800M-CXP / EL-2800C-CXP

- 8 -

3. Main features

New Elite Series, 2/3 ” progressive scan camera

Intelligent body design for easy and flexible installation

Utilizes new CoaXPress interface using a single coaxial cable

Aspect ratio 4:3, 1920(H) x 1440(V), 2.8 million effective pixels

4.54 μm square pixels

S/N 61dB for monochrome and 58.5dB for color

8-bit, 10-bit, or 12-bit output for monochrome and Bayer or 8-bit per color output for RGB

color

54.7 frames/second with full resolution in continuous operation for 1X -2YE output format

(monochrome or Bayer) as well as for RGB output in Quad Sensor Tap Geometry and 6.25Gbps

Link Configuration, 15.8 frames/second for 1X –1Y output format including RGB output

in-camera interpolation

Various readout modes, including horizontal and vertical binning (EL-2800M-CXP only) and

ROI (Region Of Interest) for faster frame rates

0dB to +30dB gain control for EL-2800M-CXP and 0dB to +27dB for EL-2800C-CXP

10 μs (1/100,000) to 8 seconds exposure control in 1 μs step

Auto exposure control

Timed and trigger width exposure control,

RCT, PIV and sequential trigger modes for specific applications

ALC control with combined function of AGC, auto exposure, and auto iris

Various pre-processing circuits are provided

Programmable LUT

Gamma correction from 0.45 to 1.0

Shading compensation

Bayer white balance with manual or one-push auto (EL-2800C-CXP only)

Bayer color interpolation (EL-2800C-CXP only)

Blemish compensation

Test pattern signal generator is built in

Auto iris lens video output with H-sync

New Hirose 10P connector for lens interface including P-Iris lens control

C-mount for lens mount

This manual suits for next models

Table of contents

Popular Security Camera manuals by other brands

ADEMCO

ADEMCO RapidDome Owners Operating & Installation Guide

EverFocus

EverFocus EBA2880 user manual

Honeywell

Honeywell OptiCAM-IR Installation and setup guide

Uniq

Uniq UC-600 user manual

OPTICOM

OPTICOM NVD-120-S datasheet

Steren

Steren CCTV-221 instruction manual

Arm Electronics

Arm Electronics C420BCDNVFIR Features

Eneo

Eneo PLD-2036PTZ installation guide

Axis

Axis AXIS M20 Series installation guide

Panasonic

Panasonic KX-HCM230 operating instructions

COP-USA

COP-USA CC15NV-SL Specifications

Active Silicon

Active Silicon HARRIER H.264 quick start guide

Motorola

Motorola Avigilon 1.3C-H5SL-BO1-IR installation guide

INSTEON

INSTEON 2864-232 user manual

Wisenet

Wisenet XNB-6002 quick start guide

Axis

Axis M5525-E user manual

Vitek

Vitek VTC-IR62NZ922 user guide

Panasonic

Panasonic WV-SF342 Specifications

JAI EL-2800M-CXP User manual

Popular Security Camera manuals by other brands