JamHub Tracker MT16 User manual

1
TM
© 2014 JamHub Corp. All Rights Reserved.
P.O. Box 482 Whitinsville, MA | www.JamHub.com

2
Tracker MT16™ — User Guide
© 2014 JamHub Corp. All rights reserved. Product features, specications, system requirements,
and availability are subject to change without notice. Patents Pending.
TABLE OF CONTENTS
WELCOME 4
INTRODUCTION 4
Safety Precautions 4
Electrical Interference 4
Register Your Tracker MT16 4
Update Your Tracker MT16 4
FCC Warning 5
Declaration of Conformity 5
WHAT’S IN THE BOX? 6
Connections 6
Lights 7
Buttons 7
POWER 8
Powering Your Tracker MT16 8
TRACKER CONNECTIONS 8
Connecting Your Tracker MT16 8
ON BOARD INPUTS 8
Your Tracker MT16 has 8 Built-in Mono Inputs 8
Why a Half Insert? 9
Connecting Your Tracker MT16 to a JamHub Studio 10
Using the Tracker MT16 Breakout Cable 11
SAVE THE MUSIC 11
Insert Your SD Card 11
Formatting Your SD Card 11

3
RECORDING 12
Preparing to Record 12
Arming Channels 12
Select Your Channel Mapping Option 12
Record Modes - Split or Combined 12
Sample Rate - 44.1kHz, 48kHz, 96kHz 13
Audio Formats - WAV, or MP3 13
Record - ON/OFF 14
Naming Your Files 14
Recording 15
REVIEWING YOUR RECORDINGS 16
How to Listen to a Recording 16
CONNECTING TO THE WEB 16
How to Set Up Your Wireless Network - WiFi 16
What is BandLab™? 17
How to Link to Your BandLab™ Account 17
BandLab™ Cloud 17
Ethernet 10/100 Megabits Per Second (Mbps) 18
Status 18
STORAGE 19
To Reformat Your SD Card 19
To Update Your Tracker MT16 19
To Restore Factory Defaults 19
Troubleshooting 19
Warranty 20

4
Tracker MT16™ — User Guide
© 2014 JamHub Corp. All rights reserved. Product features, specications, system requirements,
and availability are subject to change without notice. Patents Pending.
INTRODUCTION
This guide is intended to get you up and recording with your new JamHub Tracker MT16.
To get the most out of your experience, please read the full manual thoroughly.
If this copy is lost, a copy of the manual can always be downloaded at www.JamHub.
com. Please direct any support requests to [e-mail].
Safety Precautions
Do not let your Tracker MT16 become submerged in water, or otherwise get wet.
Do not expose your Tracker MT16 to extremes of temperature, such as in the freezer
or near an open ame. Use only the JamHub provided and approved AC adapter.
Opening the plastic housing will void the warranty, and expose the user to the
possibility of injury and electrical shock.
Electrical Interference
For your safety, the Tracker MT16 has been built with maximum protection against
external interference and the emission of internal electromagnetic radiation.
However, equipment or materials that are highly susceptible to interference or that
are prone to electromagnetic emissions should not be placed near the Tracker MT16
during operation, as it is still possible, though unlikely, for data to become corrupted.
Register Your Tracker MT16
Visit www.JamHub.com to register your Tracker MT16 today. Registration will ensure
that you’re kept up to date on all the latest soware so your unit is always on the
cutting edge of recording technology.
Update Your Tracker MT16
Visit www.JamHub.com/TrackerMT16 to nd the latest information about soware
and the most current online manual. Important: Update your Tracker MT16 as soon
as you open the box to access all your recorder’s features and xes.
Online user manuals are available in English, French, German,
Japanese and Spanish.
WELCOME
JamHub’s Tracker MT16 lets you capture the energy of your live performance, with
unparalleled quality for incredible recordings that let the music shine without being
bogged down by room noise and reection. Thanks for joining the JamHub family
with your purchase!

5
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation. Changes or modications not expressly
approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
Model #: Tracker MT16
Operating Voltage: 5V DC
Power Consumption: 19W Max
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
» Reorient or relocate the receiving antenna.
» Increase the separation between the equipment and receiver.
» Connect the equipment into an outlet on a circuit dierent from that
to which the receiver is connected.
» Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity
JamHub hereby declares that this Tracker MT16™ Multitrack Recorder
is in compliance with the essential requirements and other relevant provisions
of Directive 1999/5/EC.

6
Tracker MT16™ — User Guide
© 2014 JamHub Corp. All rights reserved. Product features, specications, system requirements,
and availability are subject to change without notice. Patents Pending.
WHAT’S IN THE BOX?
» Tracker MT16
» Tracker MT16 Protective Case
» 16GB class 10 SD RAM Card
Connections
Your new Tracker MT16 has several options for connection…
Le Side:
1. Channels 1-6 – Built-in Mono Inputs
Right Side:
2. SD Card Slot – for all Class 10 SD cards
3. USB Slot – for transfering les and future
feature options.
4. Channels 7-8 – Built-in Mono Inputs
Back:
5. Ethernet Port 10/100 – high-speed internet
access for upload and download
6. DC Adapter Input – for use with the
included 5V DC adapter
7. JamHub Connect Cable Port – to plug
your Tracker MT16 directly into your
JamHub studio
Front:
8. ⅛” Headphone Jack – for instant playback
of individual tracks
» 5V DC Adaptor
» JamHub Connect Cable
» Quick Start Guide
14
2 3
75 6 8

7
Lights
Above Display Lights:
9. PWR - Your Tracker MT16 is powered
on with proper line voltage and ready
for use.
10. LINK – Network connectivity has been
successfully established and you are ready
to upload or download data.
11. ACT – Displays real-time data packet activity
in and out of your Tracker MT16.
Buttons
Below Display Lights:
12. ARMED – Record mode is set to on and all
selected tracks will be recorded once the
button is pressed.
13. REC – You are capturing sound!
14. CLIP – Audio is beyond appropriate
levels on one or more channels and one
or more channels will need to be lowered
at the source.
Note: Any single channel will set the clip light
o letting you know that a channel is clipping
(distorting the sound) before it gets to the
Tracker MT16 inputs. Lower the level at the
source until the clip light no longer ashes.
15. Move back one level in the menu. Hold down
for 2 seconds to go back to the top menu.
16. Select your current menu option and start a
new recording when armed to record. Hold
for 3 seconds to save some selected menu
functions.
17. Move up the menu or character hierarchy
18. Move down the menu or character hierarchy
9 10 11
18171615
12 13 14

8
Tracker MT16™ — User Guide
© 2014 JamHub Corp. All rights reserved. Product features, specications, system requirements,
and availability are subject to change without notice. Patents Pending.
POWER
Powering Your Tracker MT16
Plug your Tracker MT16 into the wall using the provided 5V DC Adapter. When your
Tracker MT16 is powered on, the PWR light will turn blue and the LCD will display,
Initializing, please wait… Your Tracker MT16 is a fully functioning UNIX computer,
so it will take a moment to boot up. Once the device is ready to go, you will see the
RECORD menu.
TRACKER CONNECTIONS
Connecting Your Tracker MT16
Your Tracker MT16 is designed to connect to a variety of devices, and can be hooked
up in 3 ways: using the built-in inputs, using the JamHub Tracker MT16 Breakout
Cable (sold separately), and using the included JamHub Connect cable.
Connect your Tracker MT16 directly to any mixer using the direct out, patch, or Insert
Jack. The Insert Jack is a specially designed jack for the send and return of eects
loops: rarely used but highly prized space on a mixer.
ON BOARD INPUTS
Your Tracker MT16 has 8 Built-in Mono Inputs
These specially designed jacks will allow you to connect your recorder directly
to a mixer through the insert jacks, or to get creative.
To connect to a mixer’s insert jacks, run a stereo cable from your Tracker MT16’s
on board inputs to the insert jack. This will give you clean post-trim, pre-fader audio
without aecting the signal on your mixer.
If you would like to connect directly to your Tracker MT16 without using insert jacks,
use a mono cable and only insert it half way into the jack. This will allow you to feed
some instruments and signal paths directly into your recorder when you need to.

9
Why a Half Insert?
Insert Jack signals have 3 components: a Send, a Return, and a Ground. If you fully
insert a mono cable, the lack of a Return will cause the signal to ground out. By using
the Half Insert technique, you will ensure that only the Send continues through the
mixer and you will not shut o the channel strip. If the Channel stops making sound
in your mixer, you have fully inserted the cable. Simply adjust back to a half-insert
connection (see below).
Full Insert
Half Insert

10
Tracker MT16™ — User Guide
© 2014 JamHub Corp. All rights reserved. Product features, specications, system requirements,
and availability are subject to change without notice. Patents Pending.
Connecting Your Tracker MT16 to a JamHub Studio
Your Tracker MT16 comes with a JamHub Connect cable to connect to any JamHub
studio. Simply plug the JamHub Connect cable into the JamHub Connect port on the
back of your Tracker MT16, and plug the other side into any of the SoleMix™ remote
ports on the back of your JamHub studio.
When recording from a JamHub studio, it is important to note that the Tracker MT16
will be recording up to 7 stereo channels of live audio, and that the microphone and
instrument inputs on each SoleMix section are summed before being recorded.
So if you have a guitar and a microphone plugged into Section 1 (blue) of your
JamHub studio, the Tracker MT16 will record these as 1 stereo signal, rather than
2 separate audio sources. The global eects (the FX bus) in your JamHub studio will
be recorded in a separate stereo channel should you want it during postproduction.

11
Using the Tracker MT16 Breakout Cable
To gain full access to the Tracker MT16’s multitrack recording, you will need to use
the Tracker MT16 Breakout Cable (sold separately). Plug into the jack located next
to the DC Adapter port, and seamlessly connects to your mixing desk through the
Insert Jacks.
SAVE THE MUSIC
How Your Tracker MT16 Saves Files
The Tracker MT16 saves les onto the included SD card. Each channel’s recording
is saved as one WAV or MP3 le. Most DAWs will open a WAV and MP3, but be sure
to check with your DAW manufacturer for compatibility. In addition, the Tracker
COMBINED mode will save all tracks recorded in a single WAV le that contains all
the data needed for a multitrack session. COMBINED les will encode more quickly
and are easier to transfer across the web. You can break these les out into their
component pieces on your computer using the breakout utility, which you can learn
more about online at www.JamHub.com/TrackerMT16, or upload them to Bandlab.
Insert Your SD Card
Firmly push your SD card in your Tracker MT16 with the gold connections facing
up and the label facing down.
Formatting Your SD Card
To format a new SD Card for your Tracker MT16, go to SETTINGS, then scroll through
the menu to the Format SD option and press . Be aware that reformatting
an SD Card will wipe any preexisting data o that card and you will lose any les
previously stored on the SD Card.

12
Tracker MT16™ — User Guide
© 2014 JamHub Corp. All rights reserved. Product features, specications, system requirements,
and availability are subject to change without notice. Patents Pending.
RECORDING
Preparing to Record
Before you record, you will need to set Record Mode, Sample Rate, and Audio Format
and arm the individual channels you wish to record. These options can all be found
in the Settings Menu.
Arming Channels
In the Channels menu, scroll through the numbered channels and switch those you
wish to record to On or O using the button.
Menu Top
»Setting → Audio → Channels 1-16
» Choose channels to record by turning them ON or OFF.
» Hold for 3 seconds to save.
» Channels are now armed and ready for recording
NOTE: Save space on your SD Card by turning o unused channels. Why record dead air
if you don’t have to?
Select Your Channel Mapping Option
To ensure that you have the easiest possible le managment, your Tracker MT16
allows you to tell it which devices you are interfacing with while recording.
»Settings → Audio → Channel Mapping
» Chose “JamHub for JamHub studios, “TRS” for the built-in inputs,
or “Snake Cable” for the breakout cable
» Hold for 3 seconds to save
Record Modes - Split or Combined
Your tracks may be saved as individual WAV or MP3 le using SPLIT mode, or all
16-channels can be saved as a COMBINED WAV which will appear as one saved le.
Recording in COMBINED mode reduces the amount of time your Tracker MT16 will need
to encode, streamlining your recording experience. To break COMBINED les out into
their component WAV les, run the Breakout Utility on your computer (found on your
SD card and available to download at JamHub.com) or upload your les to BandLab.
Menu Top
»Setting → Audio → Record Mode
» Choose Split or Combined using or buttons
» Save by pressing on the desired option, an ‘*’ indicates the current setting

13
Sample Rate – 44.1kHz, 48kHz, 96kHz
Set your sample rate according to your recording needs, but note that sampling
rates are calculated by the speed of the media storage device connected. If you try
to record at higher frequencies than the device can support, you may lose audio.
Menu Top
»Setting → Audio → Sampling Rate
» Choose 44.1kHz, 48kHz or 96kHz using or buttons
» Save by pressing on the desired option, an ‘*’indicates the current setting
When recording in 96kHz, it is inadvisable to use an SD card. The les you produce
when recording in this mode are too large for the average SD card, so only channels
1-6 may be activated during 96KHz recording when using an SD card. Recording using
the JamHub mapping will also be disabled in this mode.
To record all 16 channels of audio in 96KHz, make sure that your Tracker MT16
is running soware revision #2.0 or higher.
»Settings →Status →Firmware Rev
Once you have updated your Tracker MT16, reference the latest online manual for
information on hooking up an external drive via USB.
Audio Formats - WAV, or MP3
Your Tracker MT16 supports WAV or MP3 le formats. WAV les are commonly used
for high quality recordings and are large le sizes. MP3 les compress your audio,
allowing you to record more and send les across a network more easily.
Menu Top
»Setting → Audio → Audio Format
» Choose WAV or MP3 using or buttons
» Save by pressing on the desired option, an ‘*’indicates the current setting

14
Tracker MT16™ — User Guide
© 2014 JamHub Corp. All rights reserved. Product features, specications, system requirements,
and availability are subject to change without notice. Patents Pending.
Record - ON/OFF
The Tracker MT16 uses high quality analog to digital (A/D) converters, ensuring that
you get accurate recordings every time you play. Setting the Record option to ON will
turn on the A/D converters and prepare them for recording. With your Tracker MT16
armed for recording, you will see the ARMED LED light turn on and the LCD will display
a time counter, audio format and sampling rate.
Menu Top
» Record ON/OFF
» Choose Record ON or OFF using or buttons
» Save by pressing on the desired option, an ‘*’indicates
the current setting
While your Tracker MT16 is armed for recording, the CLIP light will be active, ashing
red when incoming signal is too hot and needs to be turned down. Check your sound
and levels with your recorder armed.
Naming Your Files
To change the name of a take before you have recorded it:
1. Arm your Tracker MT16
2. Hold for 3 seconds, a cursor will appear
3. Use and to move the cursor
4. Use and to change the character
5. Save the le name by holding for 3 seconds

15
Recording
Once you have armed your Tracker MT16, you can begin capturing audio by pressing .
You will see the REC light come on to assure you that all is going according to plan.
The LCD screen will display a variety of information, including the name of your
track, the sample rate at which it is being recorded, the length of time you have
beenrecording, and the amount of space you have le on your SD card to record on.
Note: Your Tracker MT16 will monitor the space le on your SD card and take the
precaution of properly ending your recording when levels drop below a certain
threshold to allow for proper encoding.
In COMBINED mode, your recording will stop when you have less than 100MB of free
space. In SPLIT mode, your recording will stop when you have less than 2GB of free
space.
To stop recording, press again. Your Tracker MT16 will remain armed for recording
until you press .
Menu Top
» Record ON
» Press to start and stop recording
» Pressing stop will nalize the recorded le by displaying Encoding…
if SPLIT mode was selected.
» Combine mode recording is the quickest and the highest quality mode
for recording more than 6 channels at a time.
NOTE: Wait until encoding is complete to avoid any loss of recorded les.

16
Tracker MT16™ — User Guide
© 2014 JamHub Corp. All rights reserved. Product features, specications, system requirements,
and availability are subject to change without notice. Patents Pending.
REVIEWING YOUR RECORDINGS
How to Listen to a Recording
In your Tracker MT16’s top level menu, you will nd PLAY. By entering the PLAY menu
you will be able to scroll through any recordings you have made in SPLIT mode and
listen to them using the headphone out on your Tracker MT16.
Menu Top
» Play
» Navigate using the and button to your recorded le
» Press to play, press to stop playing
Note: Play function only supports single track playback
CONNECTING TO THE WEB
Setting your Tracker MT16 up on your wireless network makes it possible to get free
soware updates wirelessly and to upload your les to www.BandLab.com wirelessly,
which allows you to edit, mix, and share your music.
How to Set Up Your Wireless Network – WiFi
Wireless options are located in the WiFi menu, under Settings. You can turn the
Tracker MT16’s wireless uploading capabilities on and o, select your network,
and enter a password should your network require one.
» Menu Top
»Settings → Network → Wi-Fi
» Press to turn your network ON
» Your Tracker MT16 will take a moment to nd the network
» Press to locate the SSID
» Press to scan for available Wi-Fi routers or devices
» Use or button to scroll through desired network to connect
» Press to select the desired network
» If your network requires a password, press and enter your password using
the , to scroll character location, then press and use and to change
letters and numbers.
» Save password by holding down for 3 seconds
» You are now ready to connect, select the WiFi ON/OFF menu and press
to turn WiFi on.

17
What is BandLab™?
BandLab is your world of musical collaboration in the cloud, free to use for all the
musicians in your band. It the easiest way to upload, store, and edit your Tracker
MT16 recordings. Find out more at BandLab.com.
How to Link to Your BandLab™ Account
Link your Tracker MT16 to your BandLab account for convenient wireless uploading,
storage, and access. Visit www.BandLab.com to signup for a free account then go to
your Settings screen and follow the instructions to connect your Tracker MT16.
BandLab™ Cloud
Menu Top
»Settings → BandLab Cloud →
» Press
» AuthToken: XXXX (this number is unique for every Tracker MT-16)
»Settings → Status
» Press , use and to scroll to Ethernet MAC Address
» Log in to Bandlab, go to the Settings screen and enter your authentication
token and UID (Ethernet MAC address)
» Go to the Tracker MT-16’s Settings menu and nd BandLab Cloud
» Use and in the Connection Status menu switch between online and
oline modes. When your Tracker MT16 is online, you will be able to upload
les wirelessly to BandLab.
» While uploading, you will see a % Done indicator on the home screen.
Do not unplug or disconnect your Tracker MT16 until this indicator reads 100%.

18
Tracker MT16™ — User Guide
© 2014 JamHub Corp. All rights reserved. Product features, specications, system requirements,
and availability are subject to change without notice. Patents Pending.
Ethernet 10/100 Megabits Per Second (Mbps)
The Tracker MT16 has a built in high speed Ethernet port to connect to wired
network(s) up to 100Mbps. The advantage of a wired network is higher upload and
download receive and transfer rates to the Internet. In addition, this port can
be used for soware updates and can be used to stream audio les real-time
to a network storage device. To connect your Tracker MT16 via Ethernet, see below.
Menu Top
»Settings → Network → Ethernet
»DHCP: ON (all network conguration is automatic)
» DHCP: OFF (all network conguration is manually entered, see your network
administrator for more details)
»Static IP: (from your router)
»Static IP mask: (from your router)
»Static Gateway: (from your router)
»Static DNS: (from your router)
Status
The Tracker MT16 has a status menu for all devices connected to the Internet.
It provides soware revision numbers, SD memory space availability and unique MAC
addresses.
Menu Top
»Settings → Status
»DHCP: OFF or ON
»WiFi: OFF or ON
»WiFi IP: (the IP address provided by a network when DHCP is on)
»Eth IP: (the IP address provided by a network or manually added by the user)
» IP Mask: (the IP mask provided by a network or manually added by the user)
»Default Gateway: (the default gateway or router provided
by a network or manually added by the user)
»DNS (domain name server IP address)
»Eth MAC addr: (the unique WiFi MAC address of the Tracker MT16)
»WiFi MAC
»Code rev: (Current soware code installed in the Tracker MT16)
»SD Memory (Available memory for recording)

19
STORAGE
To Reformat Your SD Card
In the event that you need to format, or reformat, an SD card in order to make
it compatible with your Tracker MT16, you will nd the options you need in the
Settings menu.
»Settings → Format SD Card → Yes
» Your unit will display Success when it has formatted.
Note: Reformatting an SD card will delete all the information on that card, be sure you
have backed up any valuable les before reformatting.
To Update Your Tracker MT16
Visit www.JamHub.com/TrackerMT16 to nd all the latest soware and details
on getting your unit updated.
To Restore Factory Defaults
Should you be instructed to restore your Tracker MT16’s factory defaults by
a qualied JamHub support technician, you can do so easily in the Settings menu.
»Settings → Factory Defaults → Yes
Troubleshooting
Troubleshooting, frequently asked questions and setup guides are available
at www.JamHub.com or by contacting JamHub Corp. at:
1-877-JAM-HUBS in the US
[e-mail]

20
Tracker MT16™ — User Guide
© 2014 JamHub Corp. All rights reserved. Product features, specications, system requirements,
and availability are subject to change without notice. Patents Pending.
Warranty
1 YEAR LIMITED WARRANTY – JAMHUB TRACKER MT16
GENERAL TERMS: JamHub Corp (“JamHub”) warrants to the original consumer/purchaser (“Buyer”) that the products it
manufactures are free from defects in materials and workmanship at the time of purchase. This limited warranty extends
under normal use for one (1) year from the date of original purchase and covers parts and labor. Buyer must provide written
notice to JamHub within the limited warranty period of any defective product. JamHub or its authorized representative shall,
at JamHub’s option, either repair or replace such defective product in accordance with this limited warranty. This limited
warranty does not apply to expendable parts. This limited warranty does not extend to any product from which the serial
number has been removed or tampered with, or any product that has been damaged or rendered defective (a) as a result of
accident, misuse, abuse, negligence, or other external cause, (b) by the use of parts not manufactured or sold by JamHub, or
(c) by modication or service by anyone other than (i) JamHub, or (ii) a JamHub authorized service provider. JamHub is not
responsible for damage that occurs as a result of Buyer’s failure to follow the instructions that come with the product or by
operation outside the usage parameters stated in the user documentation that shipped with the product. No credit shall be
allowed for repair work performed by Buyer or unauthorized parties. Out-of-warranty repairs will be invoiced at the current
JamHub hourly rate plus the cost of parts, shipping and handling. JamHub reserves the right to elect, at its discretion, to give
Buyer a refund of Buyer’s purchase price instead of a repair or replacement. This limited warranty shall be Buyer’s sole remedy
in the event of a defective product.
JamHub products are manufactured using new materials or new and used materials equivalent to new in performance and
reliability. Spare parts may be new or equivalent to new. Spare parts are warranted to be free from defects in material or
workmanship for thirty (30) days or the remainder of the one (1) year limited warranty period for the product in which they are
installed, whichever is longer.
LIMITATIONS: EXCEPT AS EXPRESSLY SET FORTH IN THIS LIMITED WARRANTY, JAMHUB MAKES NO OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED IN DURATION TO THE LIMITED WARRANTY PERIOD SET
FORTH HEREIN. BUYER PURCHASES AND ACCEPTS JAMHUB’S PRODUCTS SOLELY ON THE BASIS OF THE LIMITED WARRANTY
EXPRESSED HEREIN. UNDER NO CIRCUMSTANCES SHALL JAMHUB BE LIABLE BY VIRTUE OF THIS LIMITED WARRANTY OR
OTHERWISE FOR ANY SPECIAL, INDIRECT, SECONDARY, INCIDENTAL OR CONSEQUENTIAL DAMAGES TO ANY PERSON OR
PROPERTY ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT. SOME STATES AND COUNTRIES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU.
PROCEDURES FOR REPAIRING OR REPLACING PRODUCT: Buyer may obtain the repair or replacement of any defective product
covered under this limited warranty through JamHub or its authorized representatives only. JamHub is responsible for all
shipping and handling charges in connection with the performance of this limited warranty. A return authorization number
assigned by JamHub and dated proof of purchase must accompany all products submitted for repair or replacement. Please
indicate the product’s serial number in all correspondence; an authorization number will not be issued in the absence of a serial
number. This limited warranty is void without a return authorization number and dated proof of purchase, and items delivered
to JamHub without a return authorization number and dated proof of purchase will be refused. Please contact JamHub at the
address, phone number or website indicated below to receive a return authorization number and to arrange for the repair or
replacement of a defective product covered by this limited warranty. Arrangements will be made and communicated to you at
that time for the return of the product directly to JamHub or to an authorized service center, as appropriate.
This limited warranty gives you specic legal rights. You may have other rights that vary from state to state or country to
country.
JamHub Corporation
In the US: (877) JAM-HUBS
www.JamHub.com or inf[email protected]om