J&M Corporation JAMP-350HC06 Owner's manual

© 2018 J&M Corporation. All rights reserved. 4/18
350W Amplifier Kit For
2006-2013 Harley®Ultra/
Street/Electra Glide Fairing
#
JAMP-350HC06
Installation
and Operation
Instructions

Product Description
This exciting new J&M ROKKER XXR 2-channel 350w
fairing speaker amplifier kit has been designed specifically
for use on the 2006-2013 Harley® StreetGlide or Ultra with
the Harley HK radio.
This is a full range class D audio amplifier and is spec’d at
175watts RMS per channel X2 channels, (350w total) driven
continuous into a 2 ohm load @ 14.4vdc.
The ROKKER XXR amplifier’s settings have been dialed in
& optimized for this exact speaker configuration, to provide
the maximum highway performance for your Harley bagger
audio system.
Amplifier mounts to the custom made stainless steel bracket
system, to provide solid and secure mounting inside the
Harley batwing fairing.
Custom made plug-n-play wiring harnesses are included
with this amplifier kit, top quality heavy gauge power/ground
wires are used for the fused battery connection, along with
all necessary mounting hardware & complete installation/
operation instructions.
Amplifier itself measures 7 1/4” X 4 ¾” X 1 ¾”.
Installation Instructions
1. Remove the outer fairing shell, seat, and fuel tank.
2. By following along the factory wiring harness, route the
amplifier power harness from the fairing, under the fuel tank,
and on to the battery. (removal of the fuel tank is necessary for
proper installation)
3. After first disconnecting the negative battery cable from
the battery, connect the positive (red) lead from the amplifier
power harness directly to the positive post of the battery. Then
connect the negative (black) lead from the power harness to
the same bolt/stud on the frame that the negative battery cable
is connected to. Then reconnect the negative battery cable to
the battery. (Figure A) Do not connect the negative (black) lead
from the amplifer to the negative post of the battery.
4. For Ultra’s and other models with a CB and/or a SAT Radio
installed, disconnect and remove them from the top of the
factory radio. (Figure B) Replace the factory retention screws
back into the radio. For models without a CB or SAT Radio,
continue with the next step.
5. Remove both the left and right forward radio mounting
bolts. Loosen but do not remove both the left and right
rearward mounting bolts. (Figure C)
6. Position the J&M Amp/Bracket assembly above the radio
and slide into position. (Remove tie-straps and re-position the
factory wiring harness as needed to allow the amplifier to fit
into place properly)
7. Replace the forward radio mounting bolts and then tighten
all (4) of the mounting bolts. (Figure D)
BATT
+
Black
Red
Master Frame
Grounding Stud
Negative
Battery Cable
Fuse
Heavy Gauge
Amplifier Power/Ground
Wire Harness
Fig. A
Fig. B
remove

Fig. D
8. Make Amplifier/Speaker connections according to
diagram. (Figure E)
FOR ULTRA’S AND MODELS WITH A CB AND/OR SAT
RADIO, CONTINUE WITH STEPS (9) THRU (11), FOR BIKES
WITHOUT A CB OR SAT RADIO, PROCEED TO STEP (12).
9. Install the previously removed CB and/or SAT Radio
modules into the J&M lower mounting bracket and secure
using the (2) 8-32x1/4 screws provided. (these are the
longer of the remaining screws) (Figure F)
10. Position the lower bracket assembly below the factory
radio and secure using the (4) remaining 8-32x3/16
screws provided. (Figure G) (Remove and re-secure any
factory wiring attached to the bottom of the radio using the
tie-straps provided)
11. Re-connect the CB and/or SAT Radio harness and
antenna connectors.
12. Test the system for proper operation before
reassembling the fairing, realizing that full sound quality
and fidelity will not be heard until the outer fairing shell is
completely reinstalled.
remove
loosen
Fig. C
Power Harness
Right Speaker
Left Speaker
Amplifier
White/
Orange
Green/
White
Gray/
Red
Green
/Black
Orange
Orange/White
Acc. wire from
headlight harness
Factory
Speaker Harness
Gray/
Red
Green/
Black
Green/
White
White/
Orange
RightLeft
Fig. E
Fig. F

Fig. G
ROKKER® XXR 350w RMS
Full Range Class D Amplifier
Output Power (RMS) @ 1% THD 1000Hz 14.4V
Stereo @ 2ohms 2 x 175 watts RMS Continuous
Frequency Response -3dB 20Hz - 31kHz Capable
S/NRatio
Separation >88dB 71dB
Input Sensitivity .35V - 3.9V 1.7V - 20V
Input Impedance 20K 2K
Specifications
Thank you for the confidence you have shown in J&M Corporation by
purchasing one of our innovative products.
If you have any question or comments about this product, you may
contact us at USA 1-520-624-7000 Monday thru Friday, 8:00AM
thru 5:00PM Mountain Standard Time.
1415 S. Cherry Avenue
Tucson, AZ 85713 U.S.A.
Tel [phone]
Website: http://www.jmcorp.com
E-mail: [email protected]
Important Programing Note: The amplifier gain & frequency response adjustments have been pre-set at our factory for this specific
Harley Davidson audio system application, using speakers with an impedance of 2-ohms, to provide maximum performance at highway
speeds. Should speaker impedance load change, alternate adjustments can be made by removing the small sticker that is placed over
the amplifier’s input gain control screw.

WARRANTY REGISTRATION FORM Please fill out this card completely and mail it immediately after purchase. Please be sure that your zip code
and serial number (if applicable) are legible. This will help us to serve you better.
(PLEASE PRINT)
Name ______________________________________________________________________________________________________________________________________________________
Address_____________________________________________________________________________________________________________________________________________________
City _______________________________ _________________________________State __________________________ Zip ______________________________________________________
Motorcycle mOther m E-mail ______________________________________________________________________________________________________
Make ___________________________________________ Model ______________________________________ Year __________________
Product part number ______________________________________________________________________
Serial number (if applicable)________________________________________________________________
Date of purchase _________________________________________________
Name of dealer it was purchased from ____________________________________________________________________________________
Mail to:
J&M Corporation
1415 S. Cherry Avenue
Tucson, AZ 85713
U.S.A.
WARRANTY AND REPAIR INFORMATION
TWO YEAR LIMITED WARRANTY In order to facilitate the servicing of this warranty, the Warranty Registration Form should be filled out and
returned within 10 days of the date of purchase. However, return of the Warranty Registration Form is not a precondition of this warranty,
and this Warranty will be observed by J&M CORPORATION whether or not the Warranty Registration Form is returned,
on the condition that other satisfactory evidence of the date of the original purchase is provided to J&M CORPORATION.
WHO PROVIDES THE WARRANTY? This warranty is provided by J&M CORPORATION.
WHO IS PROTECTED? This warranty is extended only to the original owner of this J&M CORPORATION product and may not be
transferred or assigned.
WHAT IS COVERED AND HOW LONG? This warranty covers all defects in material or workmanship of our product for a period of
2 years from date of original retail purchase. At its option, J&M CORPORATION will repair or replace any defective part(s) or equipment.
The provisions of the warranty shall not apply to any unit which has been subjected to misuse, neglect, incorrect mechanical or
electrical installation, unauthorized modifications, accident, nor to units which have been repaired or altered outside of our factory.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY In the event that the product does not conform to this warranty, the product
should be shipped prepaid to the J&M CORPORATION service facility. Transportation charges, insurance fees, and labor costs for shipment,
removal, or reinstallation of our product are not covered by this warranty. Loss or damage in shipment is the sole responsibility of the freight
carrier.
FOR YOUR INFORMATION Repair as provided under this warranty is the exclusive remedy of the consumer. J&M CORPORATION shall
not be liable for any incidental or consequential damages or for breach of any express or implied warranty on this product. Except to the
extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose on this product is limited
in duration to the duration of the warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages,
or allow limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives
you specific legal rights which vary from state to state.
J&M CORPORATION reserves the right to make changes in design and to make improvements in its products without the obligation to
incorporate the changes or improvements in any of its previously manufactured products.
J&M CORPORATION has not authorized anyone to make representations or warranties other than the warranty contained herein.
The above warranty is effective for all products manufactured after 10/01/86.
NON-WARRANTY REPAIR RATES J&M CORPORATION reserves the right to change the labor repair rates without prior notice. At the time
of this printing the out-of- warranty repair is $40 per hour for labor only. However, the customer is advised to verify the
current rate when he/she calls customer service to obtain the return authorization number.
FACTORY SERVICE ADDRESS J&M Corporation, 1415 S. Cherry Avenue, Tucson, Arizona, 85713, U.S.A. Tel: [phone] audio@
jmcorp.com www.jmcorp.com
CUSTOMER SERVICE NUMBER 1-800-358-0881