J&M JAMP-250HR06 User manual

© 2010 J&M Corporation. All rights reserved. 8/10
250W Amplifier Kit
For 2006-2011 Harley®
RoadGlide Fairing
#
JAMP-250HR06
Installation
and Operation
Instructions

Product Description
This exciting new J&M 250w fairing speaker amplifier kit has
been designed specifically for use in the 2006-2011 Harley®
RoadGlide fairing, with the Harley HK radio. (may also work
with the 1998-2005 Harley RoadGlide fairing/radio, under the
certain conditions below)
This is a full range class G amplifier and is spec’d at
125watts RMS per channel, both channels driven,
continuous into a 2 ohm load @ 14.4vdc, 70watts RMS
continuous into a 4 ohm load.
Amplifier mounts to the custom made metal mounting
bracket system.
Custom made plug-n-play wiring harnesses are included
with this amplifier kit, top quality heavy gauge power/ground
wires are used for the fused battery connection, along with
all necessary mounting hardware & complete
installation/operation instructions.
Amplifier itself measures 7 ¼” X 4 ¾“ X 1 ¾”.
Installation Instructions
1. Remove the outer fairing shell, seat, and fuel tank.
2. By following along the factory wiring harness, route the
amplifier power harness from the fairing, under the fuel tank,
and on to the battery. (removal of the fuel tank is necessary
for proper installation)
3. After first disconnecting the negative battery cable from
the battery, connect the positive (red) lead from the amplifier
power harness directly to the positive post of the battery.
Then connect the negative (black) lead from the power
harness to the same bolt/stud on the frame that the
negative battery cable is connected to. Then reconnect the
negative battery cable to the battery. (Figure A) Do not
connect the negative (black) lead from the amplifer to the
negative post of the battery.
4. Remove both of the right-side radio mounting bolts.
(Figure B)
BATT
+
Red
Black
Master Frame
Grounding Stud
Negative
Battery Cable
Fuse
Heavy Gauge
Amplifier Power/
Ground Wire Harness
Fig. A
remove
remove
Fig. B
IMPORTANT NOTE: Some 1998 thru 2005 model Road-Glides require the replacement of the factory grill assembly/speaker adapters in order for
the J&M 250w amp kit and/or 7.25 speaker kit to be installed. It will be necessary to remove the outer fairing and inspect the factory installed
grill/adapter assemblies to determine if they need to be replaced. The early style assemblies can be identified by the method of attachment to the
inner fairing. If the screws attaching the speaker go completely through the grill/adapter and into the inner fairing mounting bosses you have the early
style assemblies and they will need to be replaced with the later style factory grill/adapter assemblies and mounting hardware listed below. The later
style grill/adapter utilizes independent hardware to attach it to the inner fairing then the speaker is attached to the grill/adapter with 4 additional
screws. If you have the later style assemblies, the J&M 250w amp kit and/or 7.25 speaker kit will fit with no additional parts or hardware needed.
UPGRADE PARTS AND HARDWARE TO BE PURCHASED FROM YOUR HARLEY DEALER IF NEEDED
77021-98B LH SPEAKER GRILL KIT (Hardware included)
77022-98B RH SPEAKER GRILL KIT (Hardware included)
76234-05 SCREWPHILLIPS HEAD (8 needed)

Fig. E
Fig. F
Fig. G
Fig. H
7. Install the bracket into the fairing using the (2) longer
Allen-head bolts provided and the previously removed
speaker screw. (Figure F) If using 5.25" speakers, use of
the provided longer self-tapping speaker screw is required.
(Figure G)
8. Using (2) of the 6-32 screws, washers, and lock-nuts
provided, attach the lower amplifier mounting bracket to the
amplifier. (Figure H) Do not tighten hardware at this time.
9. Using the (2) remaining 6-32 screws, washers, and
lock-nuts, attach the amplifier to the already installed upper
mounting bracket. (Figure I) Attach the lower mounting
bracket to the lower right hand fairing mounting stud.
(Figure J) Position the amplifier upward as much as
possible and tighten all hardware.
5. Remove the upper inboard speaker screw from the right-
side J&M 7.25" speaker. (Figure C) If you are using 5.25"
speakers, remove the top speaker screw from the right-side
speaker. (Figure D)
6. Choose the correct upper amplifier mounting bracket for
the size speakers you are using. (Figure E)
Fig. D
remove
remove
7.25" speaker
7.25" speaker
5.25" speaker
5.25" speaker
Fig. C

Fig. I
Thank you for the confidence you have shown in J&M Corporation
by purchasing one of our innovative products.
If you have any question or comments about this product, you may
contact us at USA 1-520-624-7000 Monday thru Friday, 8:00AM
thru 5:00PM Mountain Standard Time.
1415 S. Cherry Avenue
Tucson, AZ 85713 U.S.A.
Tel [phone]
Website: http://www.jmcorp.com
E-mail: [email protected]
Power Harness
Right Speaker
Left Speaker
Black
Ground to
Radio Chassis
Amplifier
White/
Orange
Green/
White
Gray/
Red
Green
/Black
Orange
Orange/White
Acc. wire from
headlight harness
Factory
Speaker Harness
Gray/
Red
Green/
Black
Green/
White
White/
Orange
RightLeft
Fig. K
10. Make amplifier/speaker connections according to
diagram. (Figure K)
11. Test the system for proper operation before reassembling
the fairing, realizing that full sound quality and fidelity will not
be heard until the outer fairing shell is completely reinstalled.
Fig. J

WARRANTY REGISTRATION FORM Please fill out this card completely and mail it immediately after purchase. Please be sure that your zip code
and serial number (if applicable) are legible. This will help us to serve you better. NOTE: Lift the velcro flap on the right speaker pouch to expose serial number.
(PLEASE PRINT)
Name_______________________________________________________________________________________________________________________________________________________
Address_____________________________________________________________________________________________________________________________________________________
City _______________________________ _________________________________State __________________________ Zip ____________________________________________________
Motorcycle ❍Other ❍ E-mail ________________________________________________________________________________________________
Make ___________________________________________ Model ______________________________________ Year __________________
Product part number ______________________________________________________________________
Serial number (if applicable)________________________________________________________________
Date of purchase _________________________________________________
Name of dealer it was purchased from ____________________________________________________________________________________
Mail to:
J&M Corporation
1415 S. Cherry Avenue
Tucson, AZ 85713
U.S.A.
✃
WARRANTY AND REPAIR INFORMATION
TWO YEAR LIMITED WARRANTY In order to facilitate the servicing of this warranty, the Warranty Registration Form should be filled
out and returned within 10 days of the date of purchase. However, return of the Warranty Registration Form is not a precondition of
this warranty, and this Warranty will be observed by J&M CORPORATION whether or not the Warranty Registration Form is returned,
on the condition that other satisfactory evidence of the date of the original purchase is provided to J&M CORPORATION.
WHO PROVIDES THE WARRANTY? This warranty is provided by J&M CORPORATION.
WHO IS PROTECTED? This warranty is extended only to the original owner of this J&M CORPORATION product and may not be
transferred or assigned.
WHAT IS COVERED AND HOW LONG? This warranty covers all defects in material or workmanship of our product for a period of
2 years from date of original retail purchase. At its option, J&M CORPORATION will repair or replace any defective part(s) or
equipment.
The provisions of the warranty shall not apply to any unit which has been subjected to misuse, neglect, incorrect mechanical or
electrical installation, unauthorized modifications, accident, nor to units which have been repaired or altered outside of our factory.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY In the event that the product does not conform to this warranty, the
product should be shipped prepaid to the J&M CORPORATION service facility. Transportation charges, insurance fees, and labor costs
for shipment, removal, or reinstallation of our product are not covered by this warranty. Loss or
damage in shipment is the sole responsibility of the freight carrier.
FOR YOUR INFORMATION Repair as provided under this warranty is the exclusive remedy of the consumer. J&M CORPORATION
shall not be liable for any incidental or
consequential damages or for breach of any express or implied warranty on this product. Except to the extent prohibited by
applicable law, any implied warranty of
merchantability or fitness for a particular purpose on this product is limited in duration to the duration of the warranty. Some states
do not allow the exclusion or
limitation of incidental or consequential damages, or allow limitations on how long an implied warranty lasts, so the above
limitations or exclusion may not apply to you. This warranty gives you specific legal rights which vary from state to state.
J&M CORPORATION reserves the right to make changes in design and to make improvements in its products without the obligation
to incorporate the changes or improvements in any of its previously manufactured products.
J&M CORPORATION has not authorized anyone to make representations or warranties other than the warranty contained herein.
The above warranty is effective for all products manufactured after 10/01/86.
NON-WARRANTY REPAIR RATES J&M CORPORATION reserves the right to change the labor repair rates without prior notice. At
the time of this printing the out-of- warranty repair is $40 per hour for labor only. However, the customer is advised to verify the
current rate when he/she calls customer service to obtain the return authorization number.
FACTORY SERVICE ADDRESS J&M Corporation, 1415 S. Cherry Avenue, Tucson, Arizona, 85713, U.S.A. Tel: [phone]
[email protected] www.jmcorp.com
CUSTOMER SERVICE NUMBER 1-800-358-0881