Jands StageCL User manual

Made for LEDs
Quick Start
Version 1.3 Software

Copyright & disclaimer
This product is approved for use in Europe and Australia/New Zealand and conforms to the
following standards:
•EN55103-1
•EN55103-2
•EN60950
Conformance has been achieved for intended usage in environment E1: Residential.
To ensure continued compliance with EMC Directive 89/336 and the Australian Radio
communications Act 1992, use only high quality data cables with continuous shield, and connectors
with conductive back shells. Examples of such cables are: DMX: Belden 8102 (100% Aluminium foil
screen, 65% Copper braid).
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not properly installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•reorient or relocate the receiving antenna;
•increase the separation between the equipment and receiver;
•connect the equipment into an outlet on a different circuit from that to which the
receiver is connected;
•consult the dealer or an experienced radio/television technician for help.
Disclaimer
Information contained in this manual is subject to change without notice and does not represent a
commitment on the part of the vendor. Jands Pty Limited shall not be liable for any loss or damage
whatsoever arising from the use of information or any error contained in this manual. It is
recommended that all service and repairs on this product be carried out by Jands Pty Limited or its
authorised service agents. Jands Pty Limited cannot accept any liability whatsoever for any loss or
damage caused by service, maintenance or repair by unauthorised personnel, or by use other than
that intended by the manufacturer.
Jands lighting products must only be used for the purpose they were intended by the manufacturer
and in conjunction with the user manual. Disconnect mains power when not in use.
Copyright JANDS PTY LIMITED 2014 All rights reserved.
Designed in Australia by:
JANDS Pty Limited ACN 001 187 837
Locked Bag 15 (40 Kent Rd) MASCOT NSW 1460 Sydney
Australia
Phone: [phone]
Fax: [phone]
Web: www.jands.com
Version 1.4
#ZMA6004
10 October 2014

1
Contents
1. Welcome to the Stage CL ...........................................................1
2. Getting started...........................................................................2
Setting up the console .............................................................................................2
Switching on.............................................................................................................3
3. Patching your lights....................................................................4
Adding fixtures to the patch ....................................................................................4
4. The console controls ..................................................................7
Console layout..........................................................................................................7
Fixture Channel controls ..........................................................................................7
Using the fixture controls.........................................................................................8
Scene and Chase Controls........................................................................................9
Cuelist Controls ......................................................................................................10
Other controls ........................................................................................................11
5. Recording.................................................................................12
Recording Chases ...................................................................................................12
6. Playback ..................................................................................13
7. Autopilot .................................................................................13
8. Common Problems...................................................................13
Appendix 1: Specifications .............................................................14
1.Welcome to the Stage CL
Welcome to the Quickstart Guide for the Jands Stage CL lighting console. This
guide is intended to give you the minimum information you need to get your
Stage CL up and running as quickly as possible. The full User Manual available
on the Jands website at www.jands.com.
This manual is for consoles fitted with version 1.3 software.

2
2.Getting started
Setting up the console
Power
Connect the Stage CL’s external power supply unit to any mains supply between
100 and 240VAC. Connect the power supply’s DC connector to the Stage CL.
Feed the cable into the slot in the cable restraint.
DMX Output
The Stage CL can output one universe (512 channels) from its DMX output. Use a
5 pin DMX cable to connect the console to your lights.
Ethernet
The Stage CL supports Artnet via the Ethernet (RJ45) connector. Turn Artnet on
via the Setup menu - refer to the full user manual for more details.
USB
You can connect a USB memory stick to the console to save copies of your show
files.
Power LED
Power Switch
Power Input
Kensington Lock Point
DMX Port
Ethernet Port
USB Ports
Microphone
Cable Restraint

3
Switching on
When you switch the console power on the Stage CL starts up and displays the
opening splash screen while it loads the program. Once it finishes loading, Stage
CL displays the Home screen. If this is the first time you’ve started Stage CL not
all the buttons will be available. You have to either load a show from the ‘Shows’
window or begin a new one by patching your fixtures in the ‘Patch’ window.
Once some fixtures have been patched all buttons become available:
This button… does this…
Colour displays the Colour window. This window is used to apply
colour presets and select colours from a colour picker.
Scenes displays the Scenes window. This window is used to monitor
and edit the Scenes you record.
Chases displays the Chases window. This window is used to monitor
and edit the Chases you record.
Cuelist displays the Cuelist window. This window is used to monitor
and edit the Cuelist and Cues.
Monitor displays the Monitor window. This window is used to show
the Stage CL master control settings, what’s being played
back, the channel control settings and the DMX output
Shows displays the Shows window where you can save or load a
show.
Patch displays the Patch window where you patch your fixtures
Setup displays the Stage CL preferences windows where you can
configure the date and time, default fade settings and more.
Autopilot displays controls for automatic control of the lights.
Shutdown displays the menu used when powering off the console.

4
Home Button
The Home button is located underneath the touch screen. Press this button at any
time to return to the Home window.
3.Patching your lights
Once you've connected and powered up your Stage CL system you can patch up
to 24 fixtures (or groups of fixtures).
If it’s not already open click on the Patch button on the touch screen. Stage CL
displays the Patch window:
This is where you tell the Stage CL what sort or fixtures you are using and which
DMX channels each fixture is assigned to.
Adding fixtures to the patch
In the Patch window the fixture numbers correspond to the two pages of 12 sets
of fixture controls (flash button, fader, colour controls etc) on the front of the
Stage CL - fixtures 1 through 12 are on the first page, and fixtures 13 through 24
are on the second page. When you’re patching think about which fixtures you'll
want to use together, and put them on the same page.
The Patch Wizard
The Patch Wizard guides you through the patching process. Use the wizard to
patch fixtures already in the Library – if you need to create custom fixtures you
should create these as detailed in the following section before running the
wizard.

5
Adding to the Fixture Library
If you can’t find the fixture you want to use in the Stage CL patch window you
can create your own. To do this:
1. Select the Library tab in the Patch window. Stage CL opens the Fixture
Library window.
2. Press the ‘New’ button at the bottom of the window to start creating a fixture
from scratch. Stage CL opens the Edit Fixture window.
3. Press and release, then turn the touch screen encoder to enter details for the
first channel of the fixture. Stage CL recognises many common fixture
features.
4. Touch in the other fields or scroll across to enter values for this channel.
This field… is used to…
Dial set how the feature is accessed, either directly on a
Hue or Saturation control, or indirectly by pressing
Shift+Hue or Shift+Saturation controls.
Dflt (Default) set the value when the fixture is cleared (0 – 255)
Min (Minimum) set the minimum value for the channel (0 – 255)
Max (Maximum) set the maximum value for the channel (0 – 255)

6
5. Repeat these steps for the other fixture channels.
6. When you are finished press the Save button at the top of the window. Stage
CL saves the new fixture in the ‘My Fixtures’ folder.
The ‘Other’ feature is used for fixture channels that need to be set to a static
value for the fixture to operate correctly, like macro and mode channels.
There are no controls on the Stage CL that enable these channels to be
changed during the show.
On the Stage CL there are only 4 controls available for which to adjust fixture
parameters other than intensity, these controls being the 'direct' Hue and
Saturation, and the 'indirect' Shift+Hue, and Shift+Saturation. A normal RGB
LED fixture will use Hue and Saturation controls to control the RGB
channels, leaving Shift+Hue and Shift+Saturation controls free for other
parameters. If however the fixture does not include RGB channels, the direct
controls can be used for any desired parameter, eg Pan and Tilt, by
appropriate setting of the "Dial" fields in the fixture library.
Patching Manually
If desired, you can add fixtures to the patch individually, or change the patch
after using the Wizard. To add/change a fixture use the touch screen encoder to
scroll up or down the list to choose the fixture number, then press on the
encoder.
1. Select a manufacturer and Fixture from the list and press the Encoder to add
it to the patch.
2. To change the DMX address touch on the DMX address, press on the
encoder to select it, then use the encoder to set a new address.
3. Repeat steps 1 to 2 for the other fixtures you want to patch or change.
Copying and Pasting fixtures
To quickly patch the same fixture type to other channel numbers you can use the
copy and paste buttons. To do this:
1. Select one of the fixtures that you have already patched.
2. Press the ‘Copy’ button at the bottom of the window.
3. Scroll to the fixture number you want to use.
4. Press the ‘Paste’ button at the bottom of the window. Stage CL patches the
fixture at the next available DMX address.
5. To change the DMX address touch on the DMX address, press on the
encoder to select it, and use the encoder to set a new address.

7
4.The console controls
Console layout
Stage CL consoles provide all the faders, encoders, switches and displays you’ll
need to control your lighting rig.
The Stage CL is divided into three main sections:
•12 sets of fixture controls each with a flash button and fader for setting
intensity, 2 push button encoders for setting colour (hue and saturation)
and a ‘select’ button for grouping channels.
•A touch screen with a Home button, 3 shortcut buttons and a push
button encoder for making adjustments.
•Master control faders and buttons to control the scenes, cuelist and
chases that you record.
Fixture Channel controls
The Stage CL has 12 fixture control sets - each set lets you control the intensity
and colour of a fixture patched to that control set (see previous section).
Fixture controls
Touch screen
Master controls
Encoder

8
Fixture Master Control
The fixture master control scales the intensity of the 24 fixture channels.
The Fixtures are controlled in two pages, selected by the "Page" button.
When the Page LED is dark, the 12 control sets are controlling fixtures 1 to
12; when the Page LED is white, the 12 control sets are controlling fixtures 13
to 24.
The fixture channel faders can also be switched to control Scenes by pressing
the Fixture/Scene button – see page 12. When controlling Scenes the Page
LED will be illuminated in a colour.
Using the fixture controls
To get your fixtures outputting, first check that the Grand Master (GM) and
Master are at full. Then bring up the channel faders so your fixtures come on,
then adjust the Hue and Saturation controls to change their colours.
To speed up programming the Stage CL controls include some shortcuts and
special features:
Hue controls
Pressing on the Hue encoder lets you cycle through six preset colours. Each
time you press the encoder a new colour is selected. This action also resets the
saturation control to full.
Adjusts the saturation (whiteness) of the
fixture. For example if you had set a Red
colour you can use the saturation control to
adjust from a pure red through a pale red to
white. Can also be used for other parameters.
Adjusts the Hue (colour) of the fixture. Can
also be used for other parameters.
When lit tells you if a fixture is selected.
Selects the fixture for recording or when you
want to adjust a group together.
Shows the colour of the fixture.
Fades the intensity of the fixture from 0 to
100%
Flashes the intensity of the fixture to full when
held down.

9
Saturation controls
Pressing the Saturation encoder toggles the selected fixtures from full
saturation (full colour) to zero saturation (white).
Select buttons
If you want to adjust the colour of more than one fixture, press the select
button on all the fixtures you want to change. Then adjust the Hue and
Saturation controls on any of the selected fixtures.
To select a range of channels hold down the first fixture’s select button while
pressing the last fixture’s button.
If you select some fixtures then adjust their colour, those fixtures are
automatically de-selected when you select a new fixture.
Clear
Press the Clear button to set the colour of all selected fixtures to white.
Double-click the Clear button to set the colour of all fixtures to white – even if
they’re not selected. Triple-click to clear all fixture colours and intensities.
Holding Clear and pressing either a Scene or Chase button clears that Scene
or Chase.
Shift
To fan the colours of all selected fixtures press the Shift button and adjust a
Hue Control. The fan effect will depend on which Hue control you adjust. eg:
If you have all 12 fixtures selected and adjust the Hue control on Fixture 1 the
fan will spread from Fixture 12, which does not change colour, to the colour you
set on Fixture 1.
If you adjust the Hue control on Fixture 6 the fan will spread from Fixture 1 and
Fixture 12, which do not change colour, inwards to Fixture 6.
Scene and Chase Controls
Buttons 1, 2, 3, 4
These buttons are used to activate / deactivate the any scene or chase stored
there. They’re also used for record the Scene or Chase – see section 5.

10
The LED above each button will be off if nothing is stored there, blue if
something’s stored there but is not active, or will flash blue slowly if the scene or
chase is active. They'll also flash red when record has been pressed and they’re
empty.
Cuelist Controls
The Cuelist controls allow you to record and playback a series of looks (cues) in a
predetermined order (list). Each Cue in the list can have its own individual fade
time, and may also include both Static and Chase elements.
A Cuelist is most often used for theatre shows but is also useful for other types of
structured performance.
Play
This button starts the fade of the next cue in the list. It is also used for
recording the Cuelist – refer to Section 5.
Pause
Press this button to pause the current fade. The LED above the Pause button
illuminates when the fade has been paused.
Play Backward
This button starts a fade back to the previous cue in the list.
Release
Press this button to clear the output from the Cuelist controls.

11
Other controls
Snapshot
Press this button to take a ‘snapshot’ of the console output. The console will
hold that output until the button is pressed again. Only the Grand Master and
DBO controls have an effect on the Snapshot output. This means you can take a
snapshot, then adjust any other controls, including the fixture controls, without
affecting the look on stage. Once you have a new look ready you press the
snapshot button again and Stage CL crossfades to the new look over the
crossfade time.
Fixtures - Scenes
This button switches the 12 sets of fixture controls in and out of ‘Scene’
mode. In Scene mode the 12 faders and flash buttons can be used to record and
play back scenes.
The LED above the Fixture / Scene button is on (Red) in Scene mode.
Page
This button loads an alternate set of fixtures or scenes onto the 12 faders and
flash buttons.
The LED above the Page button changes colour depending on the page loaded.
Crossfade Time
This control adjusts Time of all manually controlled crossfades, such as
activating/deactivating a scene or chase, except the Cuelist.
Rate
Turning this encoder overrides the Chase rate, allowing you to increase or
decrease the Chase playback rate on the fly.

12
5.Recording
Recording data for playback generally involves the following steps:
1. Set up a look on your lights.
2. Press the Record button. The LEDs associated with the empty record
locations will start flashing red.
3. If necessary change the fixtures that will be recorded by pressing the
channel select buttons on each fixture page.
4. Select a location to record to. Suitable locations include the Scene
buttons 1 to 4, Chase buttons 1 to 4, the Cuelist Play button, and the 12
Channel flash buttons. Refer to the section below when recording
Chases.
Note that if a Chase is playing and a Scene is recorded, the Chase data will be
included in that Scene.
Recording Chases
When a Chase button is the record destination, the Stage CL can automatically
create a chase with the number steps equal to the number of fixtures selected. For
example:
1. Select 6 channels, make them all blue, and at full intensity.
2. Select one of the fixtures and set it to white.
3. Press the Record button. Any fixture select LEDs that come on indicate
the fixtures that will be recorded in the Chase. Check that all/only the
6 fixtures selected in step 1 have their select LEDs illuminated. If not,
change the selections so that they are.
4. Any empty locations will flash red. Briefly press an empty Chase
button 1 to 4,
5. Press “Auto” on the touchscreen.
This will create a 6 step chase with one fixture white and the rest blue.

13
6.Playback
Most controls on the Stage CL operate as Last Takes Precedence (LTP). This
means whatever was the last control you moved is the one that is now
controlling your lights. The most effective way to get a feel for how the controls
interact is to record some looks into the various controls and play them back as
you would during a show – the operation will quickly become clear.
7.Autopilot
The Autopilot facility is used for parties and other unstructured events where
you want to set the console running and leave it unattended for long periods of
time. During use the console runs the chases, changing chase every set period of
time.
8.Common Problems
1. I can’t get the mimic LEDs to illuminate on the console:
•Some or no fixtures are patched – go into the patch and check there are
fixtures patched on the expected controls.
•The Master faders are down – make sure the GM is at full and the
relevant master fader/s and fixture fader/s are pushed up.
2. The console Mimic LEDs illuminate but I cant get my lights to come on, or they
come on but not in the correct colours:
•The wrong type of fixture is patched – go into the patch and check the
fixtures that are patched match those that are connected to the StageCL.
•The DMX addresses don’t match the addresses of the patched fixtures –
check the values in the patch as compared to the settings on the fixtures.
•The fixtures aren’t receiving signal – check the cable is plugged in and/or
replace the DMX cable/s.
3. The console is generating output and I cant get rid of it:
•A scene is on – deactivate all scenes and/or pull the Scene Master down.
If necessary put the console in Scene mode and check all scenes are
disabled.
•A chase is running - deactivate all chases and/or pull the Chase Master
down.
•The Cuelist is playing back – release the Cuelist by pressing the
release button and/or pull the Cuelist Fader down.
•The Snapshot function is active – press the Snapshot button until the LED
is off.

14
Appendix 1: Specifications
Inputs & Outputs
Description Type Pin Outs Function
DMX 512 5 pin Female AXR 1
2
3
4, 5
Shield
Data –
Data +
Unused
Ethernet
(100BaseT)
RJ-45 1
2
3
4, 5
6
7, 8
Transmit +
Transmit –
Receive +
Unused
Receive –
Unused
USB (2 x) Type A 1
2
3
4
Vcc
Data –
Data +
Ground
Power 12V 5.5mm / 2.1mm
DC Power
Tip
Sleeve
+
-
General Specs
Description Value
Size 520mm wide x 300mm deep x 70mm high
Weight 4kg not including power supply
VESA Mount 100x100mm
CPU 400MHz ARM7
DRAM 128MB
FLASH 256MB
Operating System Linux
Number of Scene/Chase
Locations
92
Total number of Steps per
Chase
100+
Total number of Cues in the
Cuelist
100+