Kilews KL-WSCBSN User manual

BE Power Screw Driver
Control Display User Manual
Model: KL–WSCBSN (BE)
KILEWS INDUSTRIAL CO., LTD.
http://www.kilews.com.tw
Y2F216Q-1-002
Please scan the following QR code or download
the operation manual from KILEWS website
https://www.kilews.com.tw/tc/download-list.php

1
1. Panel Function
Display Screen:
Boot Version: (Ver 2.xxx)
16X2 LCM Display Setting Function
199: Display Job Sequence
99: Display Program
SC: Display Count Value
C: Display Screw Driver Action Turns
T: Display Screw Driver Action Time
999.9: Display Number of Turns
OKALL: Display status (OK, NGT, NGQ, NGC,...)
Up Key: Setting mode Up key switch function.
Down Key: Setting mode Down key switch function.
Left Key: Setting mode Left key switch function
Right Key: Setting mode Right key switch function
Esc Key: Press three seconds to enter/leave the setting mode.
Key: CONFIRM key
OK, NG, OKALL, start, Rev, Dis, POWER: Display status indicator.

2
1. OUTPU: External output control
2. INTPU: External input control.
3. PORT1 (RS232): Connect to DAS or wifi module
1. Switch element: turn on or turn off the module power
2. USB port: Connect to the barcode reader.
3. MicroSD Card port: Used to store data.
4. Cable communication port: Used to online.
1. Micro USB port: Used to connect Micro harness.
2. RS232: Reserved port, no function for now.
3. USB port: Used to connect bluetooth module.
4 Power supply port: Used to supply power to module.

3
2. Set Function Options and Operating Instructions
After switching on the power, to enter into the function menu, press the “Esc” key on the panel for 3 seconds, following
which password input is required to enter the menu.
CTRL Setting
Name
Set Up Time
and Value
Function Interpretation
Factory
Default
[1] SEQ Numbers
000-199
Set the Number of Job Sequence.
OFF
[2] Job Sequence
JS: 001-199
P: 01-99
Tool: T1-T9
Set the parameter program and tools used in each job sequence.
JS: 001
P: 01
Tool: T1
[3] Device ID
000-250
WSCBSN No.
000
[4] Query Tool
NA
Search for pair-up tool; suggest pairing up different tools separately.
NA
[5] Tool Pair
NA
Set the devices found from the search process in Step [4] to the planned
tool number.
NA
[6] Operator Mode
1: STD
2: ADV
STD: Execute inner parameters setting of controller.
ADV: Job sequence controlled by AMS.
STD
[7] Default Value
1: Y
2: N
Restore to factory setting value.
N
[8] Gate in Mode
1: None
2: Once
3: Twice
Select the mode of external Gate in function.
None
[9] Sequence Set
1: OFF
2: Single
Select whether to enable the switch program, tool and small cycle
through external DAS/AMS or not?
OFF
[10] BC-1 000-0
1: BC1-9
2: 1-103
3: 0-9
BC-1: Barcode 1, up to 9 in maximum.
000: (1) Switch Program:1-99.
(2) Release NS: 100.
(3) Release AS: 101.
(4) Enable Tool: 102。
(5) Disable Too: 103。
0: Select tool.
(1) Select tool: 1-9.
(2) Unspecified: 0.
BC-1
000-0
[11] Password
0000-9999
Set module password
0000
[12] Product No.
NA
Product serial number (only for warranty revision).
NA
[13] Firmware Ver.
NA
Program version description (cannot be changed).
NA
SCREW Setting
Name
Set Up Time
and Value
Function Interpretation
Factory
Default
[1] Program
U1-U99
Select program.
01
[2] Screw Count
1-99
Count the total number of screws.
05
[3] OKALL Alarm
0.1-9.9 Sec
The duration of the OKALL Alarm signal after OK Batch is completed.
1.000
[4] Slow Start Mode
SP: L0-L9
RC: 0.1-9.9 Sec
Start Speed(SP)
Start slow start stroke speed.
Slow Start Time(RC)
Slow start function setting.
SP: L0
RC: 0.0
[5] Thread Limit
HC: 0.1-999.9
LC: 0.0-999.8
High thread(HC)
Screw lock High thread(HC)
Low thread(LC)
Screw lock Low thread(LC)
H: 999.0
L: 001.0

4
[6] Time Limit
HT: 0.1-9.99
Sec
LT: 0.0-9.98 Sec
High Time(HT)
Screw lock High Time(HT)
Low Time(LT)
Screw lock Low Time(LT)
While setting LT to 0.0 sec, it will activate the pre-lock function; the
pre-lock time is the longest time of locking HT screws.
H: 9.99
L: 0.01
[7] Stop Mode
NS: N/Y
AS: N/Y
NG Stop(NS)
Does the screw driver automatically stop operation after the occurrence
OKALL Stop(AS)
Does the screwdriver automatically stop operation after OKALL or not
NS: N
AS: N
[8] Count Thread
00-99
Set the value to judge the in-place shut off.
10
3. Set Function Options and Operating Instructions
1)After switching on the power, to enter into the function menu, press the “Esc” key on the panel for 3 seconds, following
which password input is required and press key to enter the menu or if no any operation is made for 10 sec, screen
returns to the main page.
2)Press UP or DOWN key to select the setting page to enter; after that, press key.
3)If data fails to flash, check the parameters; the flashing data can be increased/decreased.
4)When data isn’t flashing, the RIGHT/LEFT keys are disabled. When data is flashing,switch to the parameter to be adjusted.
5)Press Esc to jump out from the setting page.
4. External Input Control Function Description
Connector No.
Definition
Function Description
CN 1
External start signal
input
STR_IN
1.When (CN3+CN4) is closed, the screw driver then start reverse rotation.
2.When (CN3+CN4) is open, the screw driver then stop reverse rotation.
CN 2 GND
Input power GND
CN 3
External reverse
signal input
Reverse
1.When (CN3+CN4) is closed, the screw driver then start reverse rotation.
2.When (CN3+CN4) is open, the screw driver then stop reverse rotation.
CN 4 GND
Input power GND
CN 5
External disable
signal input
Disable
1.When (CN5+CN6) is closed, the screw driver disable rotation function is turn
on.
2.When (CN5+CN6) is closed, the screw driver disable rotation function is turn
off.
CN 6 GND
Input power GND
CN 7
External Confirm key
input
Confirm
1.When (CN7+CN8) is closed, confirm is selected.
2.When (CN7+CN8) is open, there is no input status.
CN 8 GND
Input power GND
CN 9
External clear key
input
Cleared
To clear the count value, the (CN9+CN10) closed circuit can enable the function.
CN 10 GND
Input power GND
CN 11
External sensor
switch
GAT E
1.When (CN11+CN12) is closed, article is detected.
2.When (CN11+CN12) is open, there is no article detected.
CN 12 GND
Input power GND

5
5. External Output Control Function Description
Connector No.
Definition
Function Description
CN 1
Start signal output
START
1.When (CN1+CN2) is closed, the screw driver then start running.
2.When (CN1+CN2) is open, the screw driver then stop running.
CN 2
COM
This pin refers to the START signal connection negative end
CN 3
Brake signal output
BRAKE
1.When (CN3+CN4) is closed, BRAKE is displayed.
2.When (CN3+CN4) is open, there is no output status.
CN 4
COM
This pin refers to the BRAKE signal connection negative end
CN 5
Screw driver reversed
signal output
Reverse
1.When (CN5+CN6) is closed, the screw driver then start reverse rotation.
2.When (CN5+CN6) is open, the screw driver then stop reverse rotation.
CN 6
COM
This pin refers to the Reverse signal connection negative end
CN 7
After completion of
fastening a screw
OK
1.When (CN7+CN8) is closed, OK is displayed.
2.When (CN7+CN8) is open, there is no output status.
CN 8
COM
This pin refers to the OK signal connection negative end
CN 9
When error operation,
NG is displayed
1.When (CN9+CN10) is closed, NG is displayed.
2.When (CN9+CN10) is open, there is no output status.
CN 10
COM
This pin refers to the NG signal connection negative end
CN 11
When the batch, work
or job sequence
completed, OKALL is
displayed.
1.When (CN11+CN12) is closed, OKALL is displayed.
2.When (CN11+CN12) is open, there is no output status.
CN 12
COM
This pin refers to the OKALL signal connection negative end
CN 13
Vdc
Positive DC voltage
terminal
This pin is to provide the external positive voltage.
CN 14
GND
Negati
ve DC voltage
terminal
This pin is to provide the external negative voltage.
※Remarks:
1. INPUT contact, if using non-isolating (wet contact) control, it needs to connect a 10K resistor in series on the line.
2. When the automatic machine is installed, it is recommended to install the signal line on the machine and then
connects to KL-WSCBSN.
When working with automatic control, pay attention to the above items to prevent equipment damage.
6. CONFIRM Mode
Code Description Remarks
C1 External GATE signal trigger once CONFIRM mode. External GATE signal trigger once
C2 External GAT E signal trigger twice CONFIRM mode. External GATE signal trigger twice
C3 When enable “Stop Mode AS” function, LCM screen will
display “C3” when OKALL.
panel key/external switch CONFIRM key
C4 When enable “Stop Mode AS” & “Gate Mode_Once”
function, LCM screen will display “C4” when OKALL.
External GATE signal trigger once + panel
key/external switch CONFIRM key
C5 When enable “Stop Mode AS” & “Gate Mode_Twice”
function, LCM screen will display “C5” when OKALL.
External GATE signal trigger twice + panel
key/external switch CONFIRM key

6
7. ERROR CODE Mode Status Description
Code Description Remarks
E3
Voltage-drop protection When the voltage of the electric screw driver drops instantly, the action of
the electric screw driver is stopped, and the LCM displays this symbol,
representing that the screw driver is currently under low-voltage protection.
E4
Over-temperature protection When the internal temperature of the electric screw driver is too high, the
action of the electric screw driver is stopped, and the LCM displays this
symbol, representing that the screw driver is currently under
over-temperature protection.
E5
Rotation-jamming protection
When the startup of the electric screw driver motor is abnormal, the action of
the electric screw driver is stopped, and the LCM displays this symbol,
representing that the screw driver is currently under motor startup
abnormality protection.
E7 Direction push board abnormal When the electric screw driver motor is switched on, as the direction push
board is changed, the motor of the screw driver then stops action
immediately, and LCM displays this symbol.
E8 Brake signal abnormal When the electric screw driver brake signal detection is abnormal, the action
of the electric screw driver is stopped, and the LCM displays this symbol.

7
8. BARCODE Operating Instructions
1. Hardware Configuration Description
Connect the Barcode Reader to the USB port specified on the diagram.
2. Operating Functions Description
2.1 First, set the lock command on Program of WSCBSN
Enable to switch the program used for workpiece lock through the Barcode Reader
Use the KILEWS barcode to switch program among Group 1-9; there are 1-99
groups (CMD.P01-CMD.P99) of barcodes available in factory.
Description:
Stick the program barcode to be used (e.g., CMD.P01~CMD.P99) on the workpiece.
When the workpiece comes in, scan the barcode attached to the workpiece or pre-prepared
to
enable and the tool; and switch to the correct program.
2.2 Use Barcode Reader to release the AS Confirm command
When the lock of workpiece batch is completed and AS is
set, it can be released by
Barcode Reader.

8
Use KILEWS barcode format: CMD.C02 to release AS (okAll Stop) command
Description:
For the AS function already enabled on the WSCBSN. When AS occurs,
the screw driver will be locked and unable to use; operator can use the
Barcode Reader to scan the pre-prepared command barcode to release it to
facilitate the operation.
2.3 Use the Barcode Reader to release NS Confirm command
When the lock condition of workpiece is wrong, if NS is set, it can be released
by the Barcode Reader.
Use KILEWS barcode format: CMD.C02 to release NS (Nok Stop) command
Description:
For the NS function already enabled on the WSCBSN. When NS occurs,
the screw driver will be locked and unable to use; operator can use the
Barcode Reader to scan the pre-prepared command barcode to release it to
facilitate the operation.