janitza UMG 96 RM-E User manual

Doc. no. 1.040.129.0.i 02/2018
Power Analyser
UMG 96 RM-E
Residual current monitoring (RCM)
User manual and
technical data
Item no. 33.03.207
Janitza electronics GmbH
Vor dem Polstück 6
D-35633 Lahnau
Support tel. [phone]
Fax [phone]
E-mail: [email protected]
www.janitza.com
www.janitza.com
Power Analyser

2
UMG 96RM-E
Content
General 4
Inspection on receipt 6
Available accessories 7
Product description 8
Proper use 8
Performance characteristics – UMG 96RM-E 10
Measuring process 11
Operating concept 11
GridVis network analysis software 11
Connection variants 12
Mounting 13
Installation 15
Power supply 15
Measuring voltage 16
Current measurement via I1 to I4 22
Residual current measurement (RCM) via I5, I631
Temperature measurement input 35
RS485 interface 36
Ethernet interface 39
Digital in-/outputs 40
LED status bar 45
Operation 46
Display mode 46
Programming mode 46
Parameters and measured values 48
Configuration 50
Connecting the supply voltage 50
Current and voltage transformers 50
Programming the current transformer for I1 to I352
Programming the voltage transformer 53
Programming parameters 54
TCP/IP configuration 55
RS485 device address (Addr. 000) 58
RS485 baud rate (Addr. 001) 58
MODBUS gateway (Addr. 002) 59
User password (Addr. 050) 59
Parameter 60
Mean value 60
Averaging method 60
Min. and max. values 60
Mains frequency (Addr. 034) 61
Energy meter 62
Reset energy meter (Addr. 507) 62
Harmonics 63
Measured value rotation 64
Measured value indocations 64
Phase sequence 66
LCD contrast (Addr. 035) 66
Backlight 66
Time recording 67

3
UMG 96RM-E
Operating hours meter 68
Serial number (Addr. 754) 68
“Drag indicator” 69
Recordings 70
Putting into service 71
Connecting the supply voltage 71
Applying the measuring-circuit voltage 71
Applying the measuring-circuit current 71
Phase sequence 72
Check phase assignment 72
Checking the energy measurement 72
Applying the residual current 72
Failure monitoring (RCM) for I5, I6 73
Checking the measurement 75
Checking the individual outputs 75
Checking the total power outputs 75
RS485 interface 76
Digital outputs 78
Impulse output 80
Service and maintenance 86
Service 86
Device calibration 86
Calibration intervals 86
Firmware update 87
Battery 87
Battery monitoring function 88
Replacing the battery 89
Error/warning messages 90
Technical data 96
Function parameters 104
Table 1 – Parameter list 106
Table 2 - Modbus address list 110
Number formats 113
Dimension diagrams 114
Measured value displays overview 116
Connection example 1 122
Connection example 2 123
Basic functions quick guide 124
TCP/IP addressing quick guide 125

4
UMG 96RM-E
Comments on the operating manual
We welcome your comments. In the event that anything
in this operating manual seems unclear, please let
us know and send us an EMAIL to: [email protected]
Meaning of the symbols
The following pictograms are used in the operating
manual at hand:
General
Copyright
This operating manual is subject to the legal requirements
for copyright protection and may not be, either in whole
or in part, photocopied, reprinted, or reproduced
by mechanical or electronic means, or in any other
manner be duplicated or redistributed without the legally
binding, written agreement of
Janitza electronics GmbH, Vor dem Polstück 1,
D 35633 Lahnau, Germany.
Trademarks
All trademarks and their resulting rights belong
to the respective holders of these rights.
Disclaimer
Janitza electronics GmbH takes no responsibility for
errors or defects within this operating manual and takes
no responsibility for keeping the contents of this
operating manual up to date.
cDangerous voltage!
Danger to life or risk of serious injury.
Disconnect system and device from power
supply before beginning work.
mCaution!
Please follow the documentation.
This symbol warns of possible dangers
that can arise during installation,
commissioning and use.
CNote!

5
UMG 96RM-E
Instructions for use
Please read the operating manual at hand as well as all
other publications that must be drawn from for working
with this product (in particular for the installation,
operation or maintenance).
Follow all safety regulations and warning information.
If you do not follow the information, it can result in bodily
injury and/or damage to the product.
Any unauthorized changes or use of this device, which
transcend the mechanical, electrical or otherwise stated
operating limitations, can result in bodily injury or/and
damage to the product.
Any of such unauthorized changes constitute "misuse"
and/or "negligence" in terms of the warranty for
the product and therefore eliminates the warranty for
covering any potential damage resulting from this.
This device is to be operated and maintained exclusively
by specialized personnel.
cIf the device is not operated according
to the operating manual, protection
is no longer ensured and danger can come
from the device.
mConductors made from single wires must
be fitted with wire-end ferrules.
mOnly pluggable screw terminals with
the same number of poles and the
same type of construction are permitted
to be connected together.
Specialized personnel are persons, that based on their
respective training and experience, are qualified
to recognize risks and prevent potential dangers
that can be caused by the operation or maintenance
of the device.
Additional legal and safety regulations required for
the respective application are to be following during the
use of the device.

6
UMG 96RM-E
Inspection on receipt
The prerequisites of faultless, safe operation of this
device are proper transport and proper storage, set-
up and assembly, as well as careful operation and
maintenance. If it can be assumed that risk-free operation
is no longer possible, the unit must be immediately put
out of operation and secured against being put back into
operation again.
The packing and unpacking must be carried out with
the customary care without the use of force and only
using suitable tools. The devices should be visually
checked for flawless mechanical condition.
It can be assumed that risk-free operation is no longer
possible if the device, for example,
• has visible damage
• no longer works despite the mains power supply
being intact
• has been exposed to long-term adverse conditions
(e.g. storage outside the permissible climate
limits without being adapted to the room climate,
condensation etc.) or rough handling during
transportation (e.g. fall from a height, even if there
is no visible external damage etc.)
• Please check the delivered items for completeness
before you start installing the device.
CAll screw-type terminals included in delivery
are attached to the device.
Concerning these operating instructions
These operating instructions are a part of the product.
• Read the operating instructions before using
the device.
• Keep the operating instructions throughout the entire
service life of the product and have them readily
available for reference.
• Pass the operating instructions on to each subsequent
owner or user of the product.

7
UMG 96RM-E
Available accessories
Number Part no. Description
2 52.22.251 Mounting clips
1 10.01.855 Screw-type terminal, pluggable, 2-pole (auxiliary power)
1 10.01.849 Screw-type terminal, pluggable, 4-pole (voltage measurement)
1 10.01.871 Screw-type terminal, pluggable, 6-pole (current measurement I1-I3)
1 10.01.875 Screw-type terminal, pluggable, 2-pole (current measurement I4)
1 10.01.865 Screw-type terminal, pluggable, 10-pole (digital/analogue inputs/outputs)
1 10.01.857 Screw-type terminal, pluggable, 2-pole (RS 485)
1 10.01.859 Screw-type terminal, pluggable, 3-pole (Digital/impulse output)
1 08.01.505 Patch cable 2m, coiled, grey (connection UMG 96RM-PC/Switch)
1 52.00.008 RS485, external terminating resistor, 120 ohm
1 21.01.058 Lithium battery CR2032, 3V (approval i.a.w. UL 1642)
1 29.01.065 Silicone seal, 96 x 96
1 15.06.015 Interface converter RS485 <-> RS232
1 15.06.025 Interface converter RS485 <-> USB

8
UMG 96RM-E
Product description
Proper use
The UMG 96RM-E is intended for the measurement
and calculation of electrical parameters such as voltage,
current, power, energy, harmonics etc. in building
installations, on distribution units, circuit breakers
and busbar trunking systems.
The UMG 96RM-E is suitable for integration into fixed
and weatherproof switch panels. Conductive switch
panels must be earthed.
Measured voltage and measured current must derive
from the same network.
The measurement results can be displayed and can
be read out and further processed via the RS485
interface.
The voltage measurement inputs are designed for
measurements in low voltage networks, in which rated
voltages of up to 300V relative to earth and surges
in overvoltage category III can occur.
The current measurement inputs I1–I4 of the UMG 96RM-
E are connected via external ../1A or ../5A current
transformers.
By continuously monitoring the residual currents
(RCM) of an electrical system via the inputs I5 and I6,
warning pulses can be triggered if a response threshold
is exceeded. Using these, the system operator can
be alarmed before a protective equipment reacts.
The UMG 96RM-E does not provide protection against
and electric shock!
The residual current measuring is done via the current
measurement inputs I5 and I6 via an external residual
current transformer with a rated current of 30 mA.
Measurements in medium and high-voltage networks
is always done via current and voltage transformers.
mThe residual current measuring monitors
residual currents via external current
transformers and can trigger a warning
impule when a response threshold
is exceeded. Thus, the device is NOT
an independent protective device!

9
UMG 96RM-E
The UMG 96RM-E can be used in industrial and domestic
settings.
Device characteristics
• Supply voltage:
Option 230V: 90V - 277V (50/60Hz) or
DC 90V - 250V; 300V CATIII
Option 24V: 24 - 90V AC / DC; 150V CATIII
• Frequency range: 45 - 65Hz
Device functions
• 3 voltage measurements, 300V
• 4 current measurements
(via current transformers ../5A or ../1A)
• 2 residual current measurements
(via residual current transformers ../30mA) or
optionally 2 temperature measurements
• RS485 interface, Ethernet
• 2 digital outputs and additional 3 digital
inputs/outputs
• Clock and memory function

10
UMG 96RM-E
Performance characteristics – UMG 96RM-E
General
• Front panel integration device with dimensions
96x96 mm.
• Connection via pluggable screw terminals
• LCD display with backlighting
• Operation via 2 buttons
• 3 voltage and 4 current measurement inputs
• Optional 2 residual current or
temperature measurement inputs
• 2 digital outputs and 3 digital inputs/outputs
• RS485 interface
(Modbus RTU, slave, up to 115 kbps)
• Ethernet (web server)
• 256 MB flash memory
(200 MB available for records)
• Clock and bettery (with battery monitoring function)
• Working temperature range -10°C .. +55°C
Uncertainty in measurement
• Active energy uncertainty in measurement class
0.5 for ../5A transformer
• Active energy uncertainty in measurement class 1
for ../1A transformer
• Reactive energy, class 2
Measurement
• Measurement in IT, TN and TT networks
• Measurement in networks with nominal voltage
up to L-L 480V and L-N 277V
• Measuring range current 0 to 5A eff.
• True RMS (TRMS)
• Continuous sampling of the voltage and current
measurement inputs
• Continuous monitoring of residual currents with
failure monitoring
• Temperature measurement
• Frequency range of the fundamental oscillation
45Hz .. 65Hz
• Measurements of the harmonic components 1st
to 40th for ULN and I
• Uln, I, P (reference/del.), Q (ind./cap.)
• Collection of well over 1000 measured values
• Fourier analyses 1st to 40th harmonic component
for U and I
• 7 energy counters for
active energy (reference), active energy (supply),
active energy (without return barrier),
reactive energy (ind.), reactive energy (cap.),
reactive energy (without return barrier), apparent
energy, each for L1, L2, L3 and total