janitza UMG507 Operating and installation instructions

Janitza electronics GmbH
Vor dem Polstück 1
35633 Lahnau
Support Tel. [phone]
email: [email protected]
internet: http://www.janitza.de
Doc. No. 1.032.311.1
Universal Measuring Device
UMG507
Functional description
Applications

2
Generals
The UMG507 supports the protocols Modbus RTU, Modbus TCP/IP, Modbus over TCP/IP (Modbus Gateway) or
Profibus DP V0, depending in the version. This functional description is an addition to the manual and describes the
configuration of the corresponding function step by step.
More functional descriptions can be found on the CD-ROM PSWbasic/professional. At present, the following functional
descriptions are available:
- UMG507 used as remote data display for external Modbus slaves
- OPC Server Port 502
- OPC Server Port 8000 (Modbus Gateway Function)
- The webserver of UMG507
- Description of the storage of UMG507
- Description of Profibus with examples
Issue Note:
17.02.2005 First edition / Wagner
07.03.2005 Correction
All rights reserved. No part of this description may be reproduced or multiplied without the expressed written permmission
of the author. Any contraventions are punishable and will be prosecuted with all legal means.
No liability can be taken for the faultless condition of the manual or damage caused by the use of it. As failures
cannot be avoided completely, we shall be very grateful for any advice. We will try to remove any failures as soon
as possible. The mentioned software and hardware descriptions are registered trademarks in the most cases and
are subjected to the regulations by law. All registered trademarks are property of the corresponding companies
and are fully recognized by us.

3
Data types
The UMG507 uses the following data types in Modbus Master Mode:
Higbyte before Lowbyte
UMG507 description Type Size Range
float float 4 Byte +/-3.8*10-38 to 3.4*1038 (floating point format)
short short 2 Byte -32768 to 32767
u_short unsigned short 2 Byte 0 to 65535
int int 4 Byte -2147483648 to 2157583647
u_int unsigned int 4 Byte 0 to 4294967296
char char 1 Byte -128 to +127
bit Bit always reads a complete register (16Bit)
Lowbyte before Highbyte
UMG507 description Type Size Range
float.lfloat 4 Byte +/-3.8*10-38 to 3.4*1038 (floating point format)
short.lshort 2 Byte -32768 to 32767
u_short.lunsigned short 2 Byte 0 to 65535
int.lint 4 Byte -2147483648 to 2157583647
u_int.lunsigned int 4 Byte 0 to 4294967296
char.lchar 1 Byte -128 to +127
bit.lBit always reads a complete register (16Bit)
I = inverted
RS485 connection
The RS485 connection of the UMG507 is designed as a 9 pole Sub D sleeve. We recommend a 9 pole Profibus plug
for connection (Type: SUBCON-PLUS-ProfiB/AX/SC Producer: Phoenix part.No.: 27 44 38 0 or comparable).
UMG507 Profibus plug SUBCON
390Ohm 220Ohm 390Ohm
ON OFF
1B
1A
3
8
VP (5)
GND (6)
2B
2A
Connection of the bus cables:
Connect the incoming bus cables always to the terminals 1A/1B (Also at the beginning of the bus system!) The
outgoing bus cable is connected to the terminals 2A/2B. The terminal resistors are activated via the slide switch at
the beginning and end of the bus system. The terminals for the outgoing bus cable (2A/2B) are disconnected
simultaneously.

4
Application 1: Energy rates
.Task: Real energy consumption shall be counted in different rates according to the respective daytime. The rate times
have to be programmed for winter and summer time separately. The place of installation is IRAN.
The following times have been fixed:
Summer time: Winter time:
Tariff 1 (T1) from 00:00 - 10.00 h Tariff 1 (T1) from 00:00 - 12.00 h
Tariff 2 (T2) from 10:00 - 24.00 h Tariff 2 (T2) from 12:00 - 24.00 h
Energy meter T0 is the addition of T1+T2.
Strategy:
1. Fixing of the time zone offset
2. Programming of the weekly switching clock for the corresponding tariff times
3. Programming of the time zone comparator
4. Programming of the logical combinations
5. Fixing of the I/O configuration
Step 1:
The time base of UMG507 is based on UTC. The standard time in Iran is GMT+3,5h for winter time and GMT+4,5h for
summer time. This corresponds to a time zone offset of 12600sec in winter and 16200sec in summer.
The summer/winter time changeover in Iran is as follows:
Winter/summer time changeover = First day in Farvardin
Summer/winter time changeover = End of 30th day in Shahrivar
This means, a calculation from the Persian calendar to the Gregorian calendar must be carried out.
The changeover according to the Gregorian calendar would be:
Winter/summer changeover = Third Monday in March at 23:59h (20:29 UTC)
Summer/winter changeover = Third Wednesday in September 23:59h (20:29 UTC)
Those data can be programmed via PSW.

5
Step 2:
Programming of the weekly switching clock channels
Switching clock channel No.1 (for summer Tariff 1) Switching clock channel No.2 (summer Tariff 2)
Weekday first : Monday Weekday first : Monday
Weekday first : Sonday Weekday first : Sonday
Hours: 00:00 Hours: 10:00
Minutes: 10:00 Minutes: 23:59
Switching clock channel No.3 (for winter Tariff 1) Switching clock channel No.4 (winter Tariff 2)
Weekday first : Monday Weekday first : Monday
Weekday first : Sonday Weekday first : Sonday
Hours: 00:00 Hours: 12:00
Minutes: 12:00 Minutes: 23:59
Programming of the function combinations in
panel „Logic operations for maker flags“
Step 3:
Programming of the time zone offset comparator.
The UMG507 saves the actual time zone offset on address Adresse 7194. This offset is 12600sec during winter and
16200 sec during summer. The comparator contains the actual status after programming. If the time zone offset is
> 12600sec the output of the comparator is active.
Input parameter 7194 .

6
Step 4:
Programming of the logic.
In the logic is checked, which switching clock channel is active, and if it is summer or winter.
The combinations would be as follows:
Time switch channel 1 AND Comparator 1 = Flag 82 //Summer Tariff 1
Time switch channel 2 AND Comparator 2 = Flag 83 //Summer Tariff 2
permanent active NOT AND Comparator 1 = Flag 84 //Inverting comparator
Time switch channel 3 AND Flag 84 = Flag 85 //Winter Tariff 1
Time switch channel 4 AND Flag 84 = Flag 86 //Winter Tariff 2
Flag 82 OR Flag 85 = Flag 87 // Result Tariff 1 Active
Flag 83 OR Flag 86 = Flag 88 // Result Tariff 2 Active
Programming of the function combinations in
panel „Logic operations for maker flags“
Step 5:
Programming of the output configuration
The flags are assigned to the energy meters in the I/O assignment.
Programming of the
function combinations in
panel „Output channels“

7
Step 6:
Check functions
The function check can be carried out via the display of the UMG 507 or aided by PSWprofessional. In PSWprofessional
the topology is used for that purpose. All actual flag and switching clock conditions are displayed here.
Use right mousekey on the device in topology
and select function “show all measured values“.
The topology must be „online“.
One more possibility is to drag all important parameters into the display of UMG507.
The following parameters are useful:
Time channel 1 = Parameter: 3296
Time channel 2 = Parameter: 3297
Time channel 3 = Parameter: 3298
Time channel 4 = Parameter: 3299
Comparator 1 = Parameter: 3320
Flag 82 = Parameter: 3360
Flag 83 = Parameter: 3361
Flag 84 = Parameter: 3362
Flag 85 = Parameter: 3363
Flag 86 = Parameter: 3364
Flag 87 = Parameter: 3365

8
Application 2: Email for short interruptions
Task: An Email must be sent after a trigger event (e.g. short interruption). The email shall transmit the starting and
ending time of the short interruption. Starting and ending time shall be deposited in the parameter memory additionally.
The status of the short interruption must be provided on a digital output.
The following conventions have been made:
1. Digital output 1 active = Short interruption active
2. Digital output 1 chopped = Short interruption was active
3. Digital input 2 resets the status of the digital output
Steps:
1. Input DNS address.
2. Email configuration.
3. Fixing the limits.
4. Programming of the logical combinations.
5. Fixing of the I/O configuration.
Step 1:
Enter the IP address of your DNS servers first.
Please ask your system administrator for the
corresponding settings.
Step 2:
For the Email Account configuration, you need
the following data from your system
administrator
1. Server name = Post output (SMTP)
2. Account name
3. Password for your Email account
4. Authentification (Login, Plain, Cram-MD5)
5. Email address of UMG507 (Mail from)
6. Subject
5. User address
Note:
If several recipients must receive the same
email, the email adresses must be separated
by a semicolon.
Example:[email protected];[email protected]

9
The following short descriptions are entered within the Email text (see address list):
<ul1min> = Minimum value of voltage in phase L1.
<ul2min> = Minimum value of voltage in phase L2.
<ul2min> = Minimum value of voltage in phase L3.
<tsu1minon_s> + <tsu1minon_m> = Start of short interruption in UTC time (Seconds + Milliseconds).
<tsu1minoff_s> + <tsu1minoff_m> = End of short interruption in UTC time (Seconds + Milliseconds).
The short interruptions are set to the actual values while creating the email. The minimum values have the average of
10 periods. More exact data are saved in the trigger memory (True RMS values over 128 periods) and can be read with
PSWbasic/professional. If the clock of the UMG507E/EP is synchronized by a NTP Server, the accuracy of the time
is about10 to 20ms. Three emails are required.
Email text No. 1 for phase L1: Email text No. 2 for phase L2:
L1 <ul1min> V L2 <ul2min> V
L2 <ul2min> V L3 <ul3min> V
L3 <ul3min> V L1 <ul1min> V
from <tsu1minon_s>sec + <tsu1minon_m>ms from <tsu2minon_s>sec + <tsu2minon_m>ms
to <tsu1minoff_s>sec + <tsu1minoff_m>ms to <tsu2minoff_s>sec + <tsu2minoff_m>ms
Email text No. 3 for phase L3:
L3 <ul3min> V
L1 <ul1min> V
L2 <ul2min> V
from <tsu3minon_s>sec + <tsu3minon_m>ms
to <tsu3minoff_s>sec + <tsu3minoff_m>ms
Step 3:
Fix limits for short interruptions for each phase in window
„Short interruptions / Overcurrents“ .
Low voltage phase L1
Low voltage phase L2 Low voltage phase L3
Saving the true RMS values
within the trigger memory.

10
Step 4:
In window „Logic“, the functional combinations are programmed.
No.: Source 1 Operator Source 2 Target flag
1 Permanently inactive AND Permanently inactive = 82
2 Short low voltage UL1 Neg. edge Permanently active = 82
3 Permanently inactive AND Permanently inactive = 83
4 Short low voltage UL1 Pos. edge Permanently active = 83
5 Permanently inactive AND Permanently inactive = 84
6 Short low voltage UL2 Neg. edge Permanently active = 84
7 Permanently inactive AND Permanently inactive = 85
8 Short low voltage UL2 Pos. edge Permanently active = 85
9 Permanently inactive AND Permanently inactive = 86
10 Short low voltage UL3 Neg. edge Permanently active = 86
11 Permanently inactive AND Permanently inactive = 87
12 Short low voltage UL3 Pos. edge Permanently active = 87
// Combinations for email sending.
13 Short low voltage UL1 Pos. edge Permanently active = 88
14 Short low voltage UL2 Pos. edge Permanently active = 89
15 Short low voltage UL3 Pos. edge Permanently active = 90
16 Flag 91 XOR Permanently active = 91
// By this assignment, the flag flashes cyclically every 200ms
17 Flag 88 OR Flag 89 = 92
18 Flag 92 OR Flag 90 = 93
// if short interruption is active in one phase, flag 93 is set
19 Flag 93 AND Flag 91 = 94
// if short interruption is active in one phase and flag 91 is active, flag 94 should flash
20 Flag 94 OR Short low voltage UL1 = 95
21 Flag 95 OR Short low voltage UL2 = 96
22 Flag 96 OR Short low voltage UL3 = 97
// the flag is active while short interruption and flashes after short interruption
23 Digital input 2 Pos. edge Permanently inactive = 88
24 Digital input 2 Pos. edge Permanently inactive = 89
25 Digital input 2 Pos. edge Permanently inactive = 90
// Resets the flashing
Description of the flags (only for information):
Flag 82 = Send Email No. 1 when short interruption L1 ends.
Flag 84 = Send Email No. 2 when short interruption L2 ends.
Flag 86 = Send Email No. 3 when short interruption L3 ends.
Flag 82 = Save parameter 5139 (time of short interruption L1 Stop)
Flag 84 = Save parameter 5145 (time of short interruption L1 Stop)
Flag 86 = Save parameter 5151 (time of short interruption L1 Stop)
Flag 83 = Save parameter 5136 (time of short interruption L1 Start)
Flag 85 = Save parameter 5142 (time of short interruption L2 Start)
Flag 87 = Save parameter 5148 (time of short interruption L3 Start)
Flag 97 =Set digital output 1 / flash.