Janome Skyline 55 User manual

Instruction Book

1
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic safety precautions should always be followed, including the
following:
This sewing machine is designed and manufactured for household use only.
Read all instructions before using this sewing machine.
DANGER— To reduce the risk of electric shock:
1. An appliance should never be left unattended when plugged in.Always unplug
this sewing machine from the electric outlet immediately after using and before
cleaning.
WARNING—To reduce the risk of burns, re, electric shock, or injury to persons:
1. Do not allow to be used as a toy.Close attention is necessary when this sewing machine is used
by or near children.
2. Use this appliance only for its intended use as described in this owner’s manual.
Use only attachments recommended by the manufacturer as contained in this owner’s manual.
3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if
it has been dropped or damaged, or dropped into water.
Return this sewing machine to the nearest authorized dealer or service center for examination,
repair, electrical or mechanical adjustment.
4. Never operate the appliance with any air opening blocked. Keep ventilation openings of this
sewing machine and foot controller free from accumulation of lint, dust and loose cloth.
5. Never drop or insert any object into any opening.
6. Do not use outdoors.
7. Do not operate where aerosol (spray) products are being used or where oxygen is being
administered.
8. To disconnect, turn all controls to the off (“O”) position, then remove plug from outlet.
9. Do not unplug by pulling on cord.To unplug, grasp the plug, not the cord.
10. Keep ngers a way from all moving parts.Special care is required around the sewing machine
needle and/or cutting blade.
11. Always use the proper needle plate.The wrong plate can cause the needle to break.
12. Do not use bent needles.
13. Do not pull or push fabric while stitching. It may deect the needle causing it to break.
14. Switch this sewing machine off (“O”) when making any adjustment in the needle area, such as
threading the needle, changing the needle, threading the bobbin or changing the presser foot, and
the like.
15. Always unplug this sewing machine from the electrical outlet when removing covers, lubricating, or
when making any other adjustments mentioned in this owner’s manual.
SAVETHESE INSTRUCTIONS
Please note that on disposal, this product must be safely recycled in accordance with relevant
National legislation relating to electrical/electronic products. If in doubt please contact your
retailer for guidance. (European Union only)
For Europe only:
This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved.Children shall not play with the appliance.Cleaning and user maintenance shall not be made
by children without supervision.
For outside Europe (except U.S.A and Canada):
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.

2
TABLE OF CONTENTS
ESSENTIAL PARTS
Names of Parts...............................................................3
Standard Accessories....................................................4
Accessory Storage.........................................................5
Extension Table..............................................................5
Free-arm sewing ............................................................5
GETTING READY TO SEW
Connecting the Power Supply........................................6
Operating Instructions:...................................................6
Machine Operating Buttons............................................7
Controlling Sewing Speed..............................................8
Foot Control....................................................................8
Function Keys.................................................................9
Raising and Lowering the Presser Foot....................... 10
Knee Lifter.................................................................... 10
Adjusting the Foot Pressure..........................................11
Dropping the Feed Dog.................................................11
Balancing Thread Tension............................................ 12
Lockout Key.................................................................. 13
Changing the Presser Foot .......................................... 13
Removing and Attaching the Foot Holder.................... 14
Replacing the Needle Plate.......................................... 15
Changing Needles........................................................ 16
Fabric and Needle Chart.............................................. 16
Winding the Bobbin...................................................... 17
Threading the Machine.................................................20
Built-in Needle Threader .............................................. 21
Drawing up the Bobbin Thread.....................................22
Selecting the Patterns..................................................23
Customizing Machine Settings..................................... 24
BASIC SEWING
Straight Stitch............................................................... 27
Securing Seams...........................................................27
Sewing from the Edge of Thick Fabric.........................27
Changing Sewing Direction..........................................27
Cutting Threads............................................................28
Needle Plate Guides....................................................28
Cornering Guide...........................................................28
Adjusting the Needle Drop Position .............................29
Adjusting the Stitch Length ..........................................29
Needle Plate for Straight Stitch....................................30
Lock-a-Matic Stitch.......................................................30
Locking Stitch...............................................................30
Straight Stitch with Left Needle Position...................... 31
Triple Stretch Stitch...................................................... 31
Knit Stitch..................................................................... 31
Sewing with Even Feed Foot (Walking foot) ................32
Zipper Sewing ..............................................................33
Rolled Hem...................................................................36
Gathering......................................................................37
Pintucking.....................................................................37
Zigzag Stitch.................................................................38
Multiple Zigzag Stitch (Tricot stitch) .............................39
Overcasting Stitch........................................................39
Knit Stitch.....................................................................40
Double Overcasting Stitch............................................40
Blind Hemming............................................................. 41
Shell Tuck.....................................................................43
Buttonholes ..................................................................43
Square Buttonhole........................................................44
Using the Stabilizer Plate .............................................48
Round End and Fine Fabric Buttonholes.....................49
Keyhole Buttonholes ....................................................49
Stretch Buttonholes......................................................49
Corded Buttonhole .......................................................50
Welted Buttonhole........................................................ 51
Button Sewing..............................................................53
Darning.........................................................................54
Tacking.........................................................................56
Eyelet............................................................................57
DECORATIVE STITCHING
Applique .......................................................................58
Fringing......................................................................... 59
Drawn Work..................................................................59
Smocking......................................................................60
Fagoting........................................................................ 61
Scallop.......................................................................... 61
French Knots................................................................ 61
Patchwork Piecing........................................................62
Patchwork.....................................................................62
Quilting.........................................................................63
Stippling........................................................................64
Clasp Stitches ..............................................................64
Free Motion Quilting.....................................................64
Hand-look Quilt Stitches...............................................65
Satin Stitches ...............................................................65
Elongation ratio ............................................................65
Twin Needle Sewing.....................................................66
PROGRAMMING A PATTERN COMBINATION
Pattern Combination.....................................................68
Programming Auto-lock Stitch......................................69
Programming Automatic Thread Cutting...................... 70
Pattern Combination with a Mirror Image..................... 71
Resuming a Pattern from the Beginning ......................72
Resuming a Pattern Combination from the Beginning.72
Bridge Stitches............................................................. 73
Monogramming ............................................................ 75
Editing a Pattern Combination......................................77
Deleting and Inserting a Pattern...................................78
Duplicating a Pattern.................................................... 78
Uniform Stitch Adjustment............................................ 79
Unied Needle Drop Position .......................................79
Individual Stitch Adjustment.........................................80
Correcting Distorted Stitch Patterns............................. 81
CARE AND MAINTENANCE
Cleaning the Hook Area...............................................82
Cleaning the Inside of the Thread Guide......................83
Problems and Warning Signals....................................84
Troubleshooting............................................................86

3
ESSENTIAL PARTS
Names of Parts
@8
@9
#0
#4
#6
#7
#1
#2
#3
q
w
e
r
t
y
u
i
o
!0
!1
!2
!3
!4
!5
!6
!7
!8
!9
@0
@1
@2
@3
@4
@5
@6
@7
@8
@9
#0
#1
#2
#3
#4
#5
#6
#7
#8
#9
$0
$1
$2
$3
$4
$5
Thread take-up lever
Foot pressure dial
Reference chart
Top cover
Touch panel stylus holder
Foot storage compartment
Bobbin thread cutter B
Bobbin winder spindle
Bobbin thread cutter A
Hole for extra spool pin
Spool pin
Spool holder (large)
Thread tension dial
Face cover
Thread cutter
Extension table (accessory storage)
Needle plate release lever
Start/stop button
Reverse button
Auto-lock button
Needle up/down button
Thread cutter button
Feed balancing dial
Knee lifter socket
Speed control slider
Touch panel (Function keys)
LCD screen
Needle clamp screw
Needle
Zigzag foot A
Needle plate
Hook cover release button
Hook cover plate
Foot holder
Setscrew
Needle threader
Buttonhole lever
Carrying handle
Handwheel
Thread cutter switch jack*
Drop feed lever
Machine socket
Foot control jack
Power switch
Presser foot lifter
NOTE:
To carry the sewing machine, hold the carrying handle
with your hand, and support the sewing machine with
the other hand.
NOTE:
Sewing machine design and specications are subject
to change without prior notice.
e
w
q
ry tui
o
!0
!1
!2
!3
!4
!5
!6 @3 @4 @5
!7
@6
@7
!8
!9
@0
@1
@2
#8
#9
$1 $2 $3 $4
$5
$0
* Thread cutter switch is an optional item.
#5

4
Zigzag foot A (set on the machine)
Rolled hem foot D
Zipper foot E
Satin stitch foot F
Blind hemming foot G
Overcast foot M
1/4 seam foot O
Darning foot PD-H
Automatic buttonhole foot R (in the
accessory storage)
Buttonhole stabilizer plate (in the
accessory storage)
Even feed foot
Quilting guide bar (for even feed foot)
Button sewing foot T
Quilting guide bar
Bobbin (5 pcs.) (1 set on the machine)
Spool holder (large, 1 set on the machine)
Spool holder (small)
Spool holder (special)
Extra spool pin
Needle set
Screwdriver
Lint brush
Seam ripper (Buttonhole opener)
Knee lifter
Needle plate for straight stitch
Touch panel stylus
Power cable
Foot control
Semi-hard fabric cover
Instructional video DVD
Instruction book
Standard Accessories
q
w
e
r
t
y
u
i
o
!0
!1
!2
!3
!4
!5
!6
!7
!8
!9
@0
@1
@2
@3
@4
@5
@6
@7
@8
@9
#0
#1
q w e r t
y u i o
!0 !1 !2
!3 !4 !5
!6
!7 !8 !9
@0 @1 @2 @3
@4 @5 @6
@7 @8
#0 #1
@9

5
Extension Table
The extension table provides an extended sewing area
and can be removed for free-arm sewing.
q Extension table
w Free-arm
To detach:
Draw the table out to the left.
To attach:
Slide the table on the base and push the table to the
right.
Free-arm sewing
Free-arm sewing is used for stitching sleeves,
waistbands, pant legs or any other tubular garments.
It is also useful for darning socks or mending knees or
elbows.
w Free-arm
r
t q
w
w
e
w
q
Accessory Storage
The accessories can be conveniently stored in the
compartment of the extension table and the compartment
under the top cover.
To store the accessories in the compartment of the
extension table, push up the cover towards you to open
the accessory storage.
q Presser foot
w Buttonhole stabilizer plate
e Automatic buttonhole foot R
r Needle plate for straight stitch
t Bobbin
y Extra spool pin
Other accessories can be also stored in the compartment
in the extension table.
q
y

6
Connecting the Power Supply
zFirst make sure the power switch qis off.
xInsert the machine plug wof the power supply cord
into the machine socket e.
cInsert the power supply plug rinto the wall outlet t,
and turn the power switch qon.
q Power switch
w Machine plug
e Machine socket
r Power supply plug
t Wall outlet
If you wish to use the foot control, insert the pin connector
into the jack on the machine.
zFirst make sure the power switch qis off.
xInsert the pin connector winto the jack eon the
machine.
cInsert the machine plug rof the power supply cord
into the machine socket t.
vInsert the power supply plug yinto the wall outlet u,
and turn the power switch on.
The foot control sign iwill be displayed when the foot
control is connected to the machine.
q Power switch
w Pin connector
e Jack
r Machine plug
t Machine socket
y Power supply plug
u Wall outlet
i Foot control sign
NOTE:
The start/stop button does not work when the foot
control is connected.
e
w
q
z
c
r
t
GETTING READY TO SEW
z
v
q
e
w
r
y
u
NOTE:
Make sure to use the power supply cable that came
with the machine.
If you turn off the power switch, wait for 5 seconds
before turning it on again.
WARNING:
While in operation, always keep your eyes on the
sewing area, and do not touch any moving parts such
as the thread take-up lever, handwheel or needle.
Always turn off the power switch and unplug the
machine from the power supply:
- when leaving the machine unattended.
- when attaching or removing parts.
- when cleaning the machine.
Do not place anything on the foot control.
i
t
Operating Instructions:
The symbol “O” on a switch indicates the “off” position of
the switch.
For the U.S.A. and Canada only
Polarized plug (one blade wider than the other):
To reduce the risk of electric shock, this plug is intended
to t in a polarized outlet only one way. If it does not t
fully in the outlet, reverse the plug. If it still does not t,
contact a qualied electrician to install the proper outlet.
Do not modify the plug in any way.

7
Machine Operating Buttons
q Start/stop button
Press this button to start or stop the machine.
The machine starts running slowly for the rst few
stitches, it then runs at the speed set by the speed control
slider. The machine runs slowly as long as this button is
pressed.
The button will turn red when the machine is running, and
green when it has been stopped.
Pressing and holding this button while sewing will slow
down the sewing speed and the machine will stop when
the button is released.
NOTE:
•Thestart/stopbuttoncannotbeusedwhenthefoot
control is connected to the machine.
•Themachinewillnotrunandthepresserfootmark
ywill blink if you start the presser foot in the up
position. Lower the presser foot and press the start/
stop button.
•Youcanselectthedesiredstart-upspeedfrom
slow, medium or high (refer to page 25).
w Reverse button
When sewing stitch pattern 01, 04-07, 11-13, 01S,
04S-07S, (mode 1) or 37-38 (mode 2), the machine will
sew in reverse as long as the reverse button is pressed.
If stitch pattern 01, 04-07, 11-13, 01S, 04S-07S, (mode 1)
or 37-38 (mode 2) has been selected and the foot control
is not connected, the machine will start sewing in reverse
as long as the reverse button is pressed.
If you press the reverse button when sewing any other
patterns, the machine will immediately sew locking
stitches and automatically stop.
e Auto-lock button
When sewing stitch pattern 01, 04-07, 11-13, 01S,
04S-07S, (mode 1) or 37-38 (mode 2) the machine will
immediately sew locking stitches and automatically stop
when the auto-lock button is pressed.
When sewing all other patterns, the machine will sew to
the end of the current pattern, sew locking stitches and
stop automatically.
The machine will trim the threads automatically after
locking the stitch when the auto thread cutting is turned
on (refer to page 70).
r Needle up/down button
Press this button to bring the needle bar up or down.
The machine will stop with the needle in down position.
However, you can change the needle stop position in the
machine setting mode (refer to page 25).
tThread cutter button
After nish sewing, press this button to trim the threads.
The needle bar automatically rises after trimming the
threads (refer to page 28).
qe
r
t
q
w
e
r
t
NOTE:
Use the thread cutter on the face cover if the thread is
#30 or thicker (refer to page 28).
y
w

8
Foot Control
Pressing on the foot control can vary sewing speed.
The harder you press the foot control, the faster the
machine runs.
NOTE:
The machine runs at the maximum speed set by the
speed control slider when the foot control is fully
depressed.
Operating Instructions:
FootcontrolmodelYC-485ECisforusewiththissewing
machine.
Controlling Sewing Speed
Speed control slider
Youcanlimitthemaximumsewingspeedwiththespeed
control slider according to your sewing needs.
To increase the sewing speed, move the slider to the
right.
To decrease the sewing speed, move the slider to the left.

9
!5 Direct pattern selection keys (refer to page 23)
Youcanselectthestitchpatterns01,04,11,and23
in mode 1 directly.
When the needle plate for straight stitch is being attached,
you can select the stitch patterns 01S or 04S only.
!6 Elongation key (refer to page 65)
Press this key to elongate satin stitch patterns.
!7 Twin needle key (refer to page 66)
Press this key when sewing with a twin needle.
!8 Mirror image key (refer to page 71)
Press this key to sew a mirror image of the selected
pattern.
!9 Set key (refer to page 24-26)
Press this key to enter the machine setting mode for
customizing the machine settings.
@0 Startover key (refer to page 72)
Press this key to sew a pattern combination from the
beginning.
@1 Lockout key (refer to page 13)
Press this key to lockout the machine when threading the
machine, replacing the accessories etc.
To reduce the risk of injury, all the buttons and keys are
deactivated.
To unlock the machine, press this key again.
@2 Memory key (refer to page 68)
Press this key to register programmed pattern
combinations.
Up to 50 stitch patterns combination can be memorized.
uw
Function Keys
qLCD screen
The LCD screen shows the following information when the
machine is turned on:
w Stitch pattern
e Mode
r Stitch pattern number
t Recommended type of presser foot
y Stitch width
u Stitch length
iCursor key (refer to page 77)
Press “ ” or “ ” to move the cursor to check or edit the
pattern combination.
oAuto thread cutting key (refer to page 70)
Press this key if you wish to cut the threads automatically
after nish sewing with a locking stitch.
When programming a pattern combination, press this key
to cut the threads automatically after nish sewing.
!0 Stitch width adjusting key (refer to pages 29, 38, 47)
Press this key to alter the stitch width.
!1 Stitch length adjusting key (refer to pages 29, 38, 47)
Press this key to alter the stitch length.
!2 Mode key (refer to pages 23, 24)
Press the mode key to select the mode.
When the power is turned on, the pattern selection mode 1
is set automatically.
!3 Number keys (refer to page 23)
Enter a 2-digit pattern number to select the desired stitch
pattern in modes 1 to 6.
!4 Clear key (refer to pages 25, 78)
Press the clear key to clear the memorized stitch pattern.
Press and hold this key until the buzzer sounds to delete
the whole pattern combination.
i!0 !1
!3
y
e
r
q
!2
!7
!8
@2
!4
!9
!6
@1
@0
!5
o
t

10
Raising and Lowering the Presser Foot
The presser foot lifter raises and lowers the presser foot.
q Presser foot lifter
Youcanraisethepresserfoothigherthanthenormalup
position. This allows for changing the needle plate, and
also helps you to place thick layers of fabrics under the
foot.
w Extra lifted position
Knee Lifter
The knee lifter is extremely helpful when sewing
patchwork, quilting etc, since it allows you to handle the
fabric while your knee controls the presser foot.
Attaching the knee lifter
Match the ribs on the knee lifter with the notches in the
knee lifter socket and insert the knee lifter.
q Knee lifter
w Rib
e Knee lifter socket
Adjusting the knee lifter
The angle of the knee lifter can be adjusted to t you.
Loosen the setscrew and slide the angle bar in or out to
adjust the angle of the knee lifter.
Tighten the setscrew to secure the angle bar.
r Setscrew
t Angle bar
Using the knee lifter
Push the knee lifter with your knee to easily move the
presser foot up and down.
Youcancontrolhowhighthefootrisesbytheamountof
knee pressure you exert.
NOTE:
Do not touch the knee lifter while stitching, otherwise
the fabric will not be fed smoothly.
q
w
q
e
w
r
t
NOTE:
Do not turn the hand wheel of press the up/down
needle button when the presser foot is in the extra
lifted position.

11
Adjusting the Foot Pressure
The foot pressure can be adjusted with the foot pressure
dial located under the top cover.
The dial has 7 setting positions from 1 to 7.
For ordinary sewing, set 5 at the setting mark.
qFoot pressure dial
wSetting mark
Reduce the pressure when sewing ne synthetics and
stretch fabrics.
To reduce the pressure, set the dial at a lower number.
Increase the pressure when sewing heavy weight fabrics.
To increase the pressure, set the dial at a higher number.
Dropping the Feed Dog
The feed dog can be lowered for sewing on buttons, free
motion quilting etc.
Shift the drop feed lever toward you to lower the feed
dog.
qDrop feed lever
wFeed dog
Shift the drop feed lever away from you to raise the feed
dog, it will return to the up position when you start the
machine.
w
NOTE:
If you start the machine with the feed dog lowered, a
message will appear on the LCD screen.
The machine will not run with the feed dog lowered
when selected following pattern numbers; 23 to 32, 34
to 36 in mode 1, stitch patterns in mode 3 to 6.
q
w
q

12
For general sewing, set the thread tension dial at AUTO,
which covers a wide range of sewing conditions.
q Thread tension dial
Balancing Thread Tension
Auto-thread tension
Manual thread tension adjustment
Youmayneedtoadjusttensionmanuallydepending
on the sewing conditions such as the type of fabric and
number of layers.
If the needle thread is too tight, the bobbin thread
appears on the right side of the fabric.
q Wrong side of fabric
w Right side of fabric
e Needle thread
r Bobbin thread
Turn the thread tension dial to a lower number to
decrease the thread tension.
q
q
w
e
r
q
w
e
r
q
w
e
r
q
w
e
r
Balanced thread tension
For straight stitch sewing, both needle and bobbin
threads will join at the middle of the fabrics.
For zigzag stitch sewing, the needle thread will appear
slightly on the wrong side of the fabric.
q Wrong side of fabric
w Right side of fabric
e Needle thread
r Bobbin thread
NOTE:
Manual thread tension adjustment may be required
when the stitch width is set more than “7.0”.
If the needle thread is too loose, the needle thread loops
on the underside of the fabric.
q Wrong side of fabric
w Right side of fabric
e Needle thread
r Bobbin thread
Turn the thread tension dial to a higher number to
increase the thread tension.

13
Changing the Presser Foot
CAUTION:
Always make sure to press the lockout key to lockout
the machine or turn the power switch off before
replacing the presser foot.
Raise the needle to its highest position and raise the
presser foot lifter.
Press the black lever on the back of the foot holder.
The presser foot will drop off.
q Lever
w Presser foot
Lockout Key
Press this key to lockout the machine when threading the
machine, replacing the accessories etc.
To reduce the risk of injury, all the buttons and keys are
deactivated.
q
t
w
Attaching the presser foot
Place the presser foot so that the pin on the foot lies just
under the groove of the foot holder.
Lower the presser bar to lock the foot in place.
Each foot is marked with an identication letter.
e Groove
r Pin
t Identication letter
e
r
To unlock the machine, press this key again.

14
Attaching the foot holder
Attach the foot holder to the presser bar from the rear.
Tighten the thumbscrew securely with the screwdriver.
Removing and Attaching the Foot Holder
CAUTION:
Always make sure to press the lockout key to lockout
the machine or turn the power switch off before
replacing the presser foot.
Removing the foot holder
Raise the presser foot and loosen the setscrew.
Remove the foot holder.
qPresser bar
wFoot holder
eSetscrew
q
w
w
e
q
e

15
Replacing the Needle Plate
Use the straight stitch needle plate when sewing ne
fabrics or sewing with straight stitches.
CAUTION:
Always make sure to press the lockout key to lockout
the machine or turn the power switch off before
replacing the needle plate.
zSlide the extension table to the left to remove it.
Turn the handwheel and raise the needle to the
highest position.
Raise and hold the presser foot lifter to the extra lifted
position.
q Presser foot lifter
w Needle
xPush down the needle plate release lever and the
needle plate will snap off.
e Needle plate release lever
r Needle plate
q
w
r
cPlace the straight stitch needle plate on the machine.
Set the left edge of the needle plate into the opening.
vPush down on the needle plate mark until the needle
plate locks in place.
Turn the power switch on or press the lockout key to
unlock.
Turn the handwheel slowly and make sure that the
needle does not hit the needle plate.
tNeedle plate mark
CAUTION:
Never press the needle plate release lever while
running the machine.
z
x
c
v
e
t

16
Changing Needles
CAUTION:
Always make sure to press the lockout key to lockout
the machine or turn the power switch off before
changing the needle.
Raise the needle by pressing the needle up/down button
and lower the presser foot.
Press the lockout key to lockout the machine or turn the
power switch off.
Loosen the needle clamp screw and remove the needle
from the clamp.
qNeedle clamp screw
Insert a new needle into the needle clamp with the at
side of the needle to the rear.
When inserting the needle into the needle clamp, push it
up against the stopper pin and tighten the needle clamp
screw rmly with a screwdriver.
wFlat side
eStopper pin
To check needle straightness, place the at side of the
needle onto something at (a needle plate, glass etc.)
The gap between the needle and the at surface should
be consistent.
Never use a blunt needle.
rGap
q
w
e
r
Fabric Thread Needle
Fine
Lawn
Georgette
Tricot
Organza
Crepe
Silk #80-100
Cotton #80-100
Synthetic #80-100
Blue tip needle
Universal needle
#9/65-11/75
Medium
Sheeting
Jersey
Broadcloth
Fleece
Silk #50
Cotton #50-80
Synthetic #50-80
Red tip needle
Purple tip needle
Universal needle
#11/75-14/90
Heavy
weight
Denim
Tweed
Coating
Quilting
Silk #30-50
Cotton #40-50
Synthetic #40-50
Red tip needle
Purple tip needle
Universal needle
#14/90-16/100
Fabric and Needle Chart
•Forgeneralsewing,useredneedle.
•Finethreadsandneedlesshouldbeusedforsewing
n e fabrics.
•Ingeneral,usethesamethreadforbothneedleand
bobbin.
•Useabluetipneedleforsewingnefabrics,stretch
fabrics, tricot and buttonholes to prevent skipped
stitches.
•Useapurpletipneedleforsewingknits,freequilting
and across the hem to prevent skipped stitches.
•Useastabilizerorinterfacetostretchornefabrics
to prevent seam puckering.
•Alwaystestthethreadandneedlesizeonasmall
piece of the same fabric you will use for actual
sewing.
NOTE:
1 x twin needle, 2 x blue tip needle (#11/75), 1 x red
tip needle (#14/90) and 1 x purple tip needle (#14/90)
are included in the needle case (Part No. 859856005).

17
Extra spool pin
Use the extra spool pin when you need to wind a bobbin
without unthreading the machine while working on a
sewing project.
Insert the extra spool pin into the hole as shown.
Place a spool of thread on the extra spool pin and x the
spool with the spool holder.
qExtra spool pin
wHole for extra spool pin
eLarge spool holder
NOTE:
The extra spool pin is also used for twin needle
sewing.
Setting the spool of thread
Lift up the spool pin. Place the spool of thread on the
spool pin.
Attach the large spool holder, and press it rmly against
the spool of thread.
qLarge spool holder
Winding the Bobbin
Removing the Bobbin
Slide the hook cover release button to the right, and
remove the hook cover plate.
qHook cover release button
wHook cover plate
Lift out the bobbin from the bobbin holder.
eBobbin
NOTE:
Use the “J” plastic bobbins for horizontal hook (marked
with “J” r). Using other bobbins, such as pre-wound
paper bobbins, may cause stitching problems and/ or
damage to the bobbin holder.
Use the small spool holder to hold narrow or small spools
of thread.
wSmall spool holder
r
q
w
e
e
Use the spool holder (special) to hold the specic size of
the spool of threads as shown.
The sizes of the spools of thread are as follows;
The hole diameter of the spool has a range of 3/8 to
7/16 (9.5 to 10.5 mm)), and the spool length has a range
of 2 3/4 to 3 (70 to 75 mm).
eSpool holder (special)
rHole diameter (3/8 to 7/16)
tSpool length (2 3/4 to 3)
Firmly insert the spool holder (special) into the hole and
hold the spool as illustrated.
r
r
t
q
w
e
e
q
w

18
z
i
e
x
w
r
t
uy
o
cPut the bobbin on the bobbin winder spindle.
r Bobbin
t Bobbin winder spindle
vPass the thread to the bobbin.
Hold the thread with both hands and wind it around
the bobbin clockwise several times.
bInsert the thread into one of the slits uof the ange
plate yand pull the thread to cut.
y Flange plate
u Slit
nPush the bobbin to the right. The bobbin mark
appears on the LCD screen.
i Bobbin mark
mStart the machine.
Stop the machine when the bobbin is fully wound and
stops spinning.
Return the bobbin winder spindle to its original
position.
,Remove the bobbin. Cut the thread with bobbin thread
cutter B o.
o Bobbin thread cutter B
NOTE:
For safety purposes, the machine will automatically
stop 1.5 minutes after starting bobbin winding.
Winding the bobbin
zPull the thread from the spool.
Hold the thread with both hands and pass the thread
into the guide slot q.
qGuide slot
xDraw the thread to the left and forward around the
thread guide w.
Draw the thread to the rear and to the right around
and under the guide plate e.
Firmly pull the thread to the right while holding it with
both hands.
wThread guide
eGuide plate
NOTE:
Set the speed control slider at the fastest position (refer
to page 8).
c v
b n
m,
q
e