Janser 111 095 000 User manual

POWER STRIPPER
Janser GmbH
Böblinger Straße 91
71139 Ehningen
GERMANY
Phone +49 / 7034 / 127-0
Fax +49 / 7034 / 8838
E-mail: [e-mail]
Internet: www.janser.com
PROFESSIONAL
FLOORING
TECHNOLOGY
OPERATING MANUAL
Order-No.: 111 095 000 (230 Volt / 50Hz) MNo.: 060283262
Order-No.: 111 093 000 (120 Volt / 60Hz)

OPERATING MANUAL 3
POWER STRIPPER
Chapter Page
1 Rules of safe operation
1.1 Electric connection 4
1.2 Staff 5
1.3 Usage 5
2 Produkt Information
2.1 Technical description 6
2.2 Technical data 6
2.3 Standard accessories 7
2.4 Optional accessories 7
3Instructions bevor use
3.1 Control 8
3.2 Assembly of the guide bar 8
3.3 Start-up procedures 9
3.4 Adjustment of the working angle 9
3.5 Changing of the blade 9
4Spare Parts
4.1 Drawing 10
4.2 List 11
5Certificate of Conformity 12
TABLE OF CONTENTS

OPERATING MANUAL
4
POWER STRIPPER
1 RULES FOR SAVE OPERATION
1.1 Electric Connection
Commandment Warning /
Caution
Hint /
Clue
Forbiddance /
Prohibition
Always disconnect power plug before servicing.
Maintenance, replacement or adjustment of hydraulic fluid or other parts can cause serious injury or
death to the user or other persons, if the machine is connected to the power supply system.
Keep the cable away from the blade to avoid damage of the cable.
Das Run over or damage of the cable can cause an electric shock.
The machine is constructed for inside-usage only.
Danger of electric shock. Do not expose the machine to water or rain.
Connection: power supply system – machine
Only to the given ranges on the type plate.
Check before usage.
Connection: cable – machine only with authorized cable.
Europe, Cable – Type: HAR HO5VV-3x2,5 mm² , Connector / Plug – Type: 2P+T16A-250v
Using cables with to little average or excessive length can cause damage to persons and objects.
Electrical equipments like cables or plugs must be controlled / renewed by an authorized electrici-
an. Risk of injuries or fatalities by wrong electrical connection
Never operate with a damaged cable or connector.
Replacement of worn or damaged cables or connectors has to be effected by a specialist or a similar qua-
lified person.
Improperly connecting the grounding wire can result in risk of electric shock.
Check with a qualified electrician if your in doubt as to whether the outlet is properly grounded. Do not
modify the plug provided with the tool. Never remove the grounding prong from the plug. Do not use
the tool if the cord or plug is damaged. If the plug will not fit the outlet, have a proper outlet installed
by a qualified electrician.
Do not use machine when cable is damage. Don't move the machine by dragging the cable. Utilization
with a damaged cable can cause an electric shock.
Non observance of the symbols, which you can see in the instruction manual or on the machine, may
result in serious injury or death for the user and other persons. Read, understand and follow all the clues
/ hints, which are situated in the machine or in the instruction manual.

OPERATING MANUAL 5
POWER STRIPPER
1 RULES FOR SAVE OPERATION
1.2 Staff
The operator has to be instructed to the use of the machine before operating.
Non observance of the instruction manual before commissioning, adjustment or maintenance could
cause serious injury to personal or objects.
Read unexceptionally all security statements. Be sure that type plate, security symbols as com-
mandments, warnings, precautions and the directives are mounted / fixe to the machine. Non
observance of the directives inside this manual may cause serious injury or damage.
Always wear eye-protection, protective suit, dust-mouthguard / dust respirator and ear-protection
during the usage of the machine. The noise that appears while removing flooring can be so intense
that at long term use it may cause injury of the auditory tube. Working without appropriate security
equipment, as for instance a protective suit, can injure eyes and body. Arising airborne dust may be inha-
led when wearing no mouthguard.
Keep arms, feet and clothes away from the operating machine parts.
Moving parts of the machine can cause serious injury or damage.
1.3 Usage
Use only the recommended accessories ensure its function before starting.
Spare parts and accessories are manufactured especially for POWER-STRIPPER.
We explicitly point out that other parts must not be used. Thereby the safety of the machine can be
negatively affected, especially the blade. The manufacturer cannot be held responsible for the perfor-
mance of any damage arising from the use of machines in which genuine spare parts have not been
used.
Work Safety
The POWER-STRIPPER is designed to the highest technical standards. Nevertheless the usage may
cause dangers for life, body and objects. Use this machine only as instructed in this operation manual
and with the machine in perfect working order. Disturbances that could impair safety, have to be elimina-
ted immediately.
Restrictions of Use
The POWER-STRIPPER may only be used for the removal of floorcovering of concrete or wood
floors. DO NOT USE THE MACHINE ON SWINGING FLOORS IN OLD BUIDINGS ! The manufacturer
cannot be held responsible for any damage or loss caused by incorrect use. Correct use also includes to
take care of all directions from the operation manual and the execution of maintenance and service.

OPERATING MANUAL
6
POWER STRIPPER
2PRODUCT INFORMATION
2.1 Technical Description
Operation:
Original Flex motor 2,0 kW, designed for continuous heavy use
Can be operatet either as hand stripper or as floor stripper
with extension handle
Easy operation by means of foot switch
Adjustable hand-grips to suit on body height
Shoulder-pad to cushion body weight when put behind
machine.
Application:
Universal use on, mid-range floor coverings, especially in
houses, e.g, textiles, PVC and semi-flexible tiles
Removal of bonded floor coverings on foam, textile or PVC
Rugged metal components for rough conditons
Working width:
210 mm
Blade dimensions:
210x60x1mm or
210x130x1 mm
Working areas:
suitable for the removal
of most types
of floor coverings
Motor:
Power 2,0 kW
Oscillations 6500 rpm
Weight 28 lbs
Noise level 85db (A)
2.2 Technical Data
210 mm
810 - 870 mm
540 mm

OPERATING MANUAL 7
POWER STRIPPER
2PRODUCT INFORMATION
2.3 Standard Accessories
-2 additional 210mm blades
-Guide handle extension - adjustable
-Crank box wrench SW10/SW13
-Open-end wrench SW 10
-3 cable-clips
2.4 Optional Accessories
-Spare 210 mm blade - lenght 60 mm
-Spare 210 mm blade - lenght 130 mm
-Metal carrying case
-Wheels attachment
- Leather Pocket for Stripper Blade
protection of hands, legs clothes
car stuff and more
-Serated Blade
Particularly to remove floor coverings
with felt-/fleece-back.
... the serated edge cuts off the fibres
... the teflon coating keeps the adhesive away from the blade.
Carrying Case
Transport Wheels
Leather Pocket

OPERATING MANUAL
8
POWER STRIPPER
3OPERATION
3.1 Control
Standard accessories
Make sure that the accessorie parts are complete
Electrical connection
Make sure that cable and connectors are in a faultless condition.
Always exchange defect electrical installations immediately
by an authorized expert.
3.2 Assembly of the guide bar
1. Put the lower guide bar (A) an the middle part (B) together
and tighten screw, nut and washer loosely.
2. Combine upper guide bar (C) and the middle part (B)
in the same way.
3. Slide the complete guide bar
into the bow handle and tighten
the two screws (D)
4. Adjust the guide bar to your body height
by adjusting the middle part (B).
The padded handle top must
touch your shoulder in working
position
5. Fix the cable clips and
hang in the connectiong
cable.

OPERATING MANUAL 9
POWER STRIPPER
3OPERATION
3.3 Starting the machine
The POWER STRIPPER comes ready for use Switch on / off with the
foot operating switch
Before beginning work with the machine slice strips into the flooring with
a regular razor knife approximately as wide as the blade attached to the machine.
Connect power supply
BEFORE USING THE MACHINE IN OLD BUILDINGS, ALWAYS CHECK STABILITY OF
THE FLOOR ! Damadges can occur on swinging floors.
When working with the POWER STRIPPER always wear HEARING PROTECTION !
3.4 Adjusting the working angle
Depending on the flooring condition of the floor covering that is to be removed, adjust
the blade with a tilted angle between 10 and a max. of 30.
If the adjusted angle is too much for the working condition, the resulting pulsation will
cause the RAPID DULLING OF THE WORKING BLADE.
If the adjusted angle is too little for the working condition, the blade will slip along the
flooring NOT CUTTING.
1. Loosen the 4 self locking nuts (which is position 41) and remove the used
blade.
2. Place the new blade in the same position.
3. Retighten the 4 self locking nuts.
DANGER OF INJURY EXISTS WHEN CHANGING THE BLADE
Always attach safety guard or leather pocket while transporting
and while not in use.
3.5 Changing of the blade

OPERATING MANUAL
10
POWER STRIPPER
4SPARE PARTS
4.1 Drawing

OPERATING MANUAL 11
POWER STRIPPER
Pos. pcc. Order-# Description DIN-Norm
0001 1,00 111 090 081 230 V: Angle Grinder SM 2006 AC without accessories
111 093 081 120V : Angle Grinder SM 2106AC without accessories
0002 2,00 016 800 142 Flat Spring B14 137
0003 2,00 004 614 020 Screw M14x20 933
0004 1,00 111 095 109 Bow-type handle
0005 2,00 111 090 112 Special-Screw M8x16
0006 1,00 004 506 050 Screw M6x50 931
0007 1,00 014 600 062 Washer B6,4 125
0008 1,00 012 300 006 Nut M6 985
0009 1,00 111 095 072 Upper Guide Bar
0010 3,00 111 090 082 Cable Clip
0011 1,00 111 090 111 Middle Part
0012 1,00 111 090 080 Working Handle
0013 1,00 004 506 050 Screw M6 x50 931
0014 1,00 014 600 062 Washer B6,4 125
0015 1,00 012 300 006 Nut M6 985
0016 2,00 006 405 005 Screw M4,2x16 7981
0017 1,00 111 090 073 Lower Guide Bar
0018 1,00 111 090 079 Padded Hanle Top
0019 1,00 111 095 551 Foot operating switch
0020 2,00 008 412 625 Ejot-Screw KB 50x45 WN 1442
0021 1,00 111 095 070 Fastening metal
0022 4,00 016 600 082 Flat spring B8,1 127
0023 4,00 004 608 010 Screw M8x10 933
0024 4,00 111 090 078 Rubber
0025 4,00 004 005 025 Screw M5x25 912
0026 4,00 111 095 080 Distance bush
0027 1,00 111 095 074 Bearing case
0028 1,00 111 090 076 Ball bearing 6006-2RS1
0029 4,00 012 300 006 Nut M6 985
0030 1,00 111 095 069 Cover metal
0031 6,00 016 600 051 Flat spring A5,1 127
0032 6,00 004 005 010 Screw M5x10 912
0033 4,00 016 600 082 Flat Spring B8,1 127
0034 4,00 004 608 010 Screw M8x10 933
0035 1,00 111 095 075 Excentric washer
0036 1,00 111 090 068 Upper base metal
0037 4,00 009 806 016 Screw M6x16 63301
0038 1,00 111 095 095 Front metal piece
0039 1,00 111 080 001 Spare blade 210 x 60 mm
0040 1,00 111 090 101 Safety guard
0041 4,00 012 300 006 Nut M6 985
0042 1,00 111 095 108 Plastic tube
0043 1,00 237 101 020 Cover
0044 2,00 004 610 020 Screw M10x20 933
0045 1,00 111 095 082 Distance Washer 3mm
Spare / Optional Accessories
1,00 111 090 093 Open-end wrench SW10
1,00 111 090 096 Crank box wrench SW10 /SW13
1,00 111 080 001 Spare blade 210 - 60 mm length
1,00 111 080 002 Spare blade 210 - 130 mm length
1,00 111 095 400 Serated Blade
1,00 111 092 000 Leather Pocket for blade
1,00 111 090 200 Carrying case
1,00 111 095 900 Wheels attachment
4SPARE PARTS
4.2 List

DECLARATION OF CONFORMITY
We Janser GmbH
Maschinen- und Gerätebau
Böblinger Straße 91
71139 Ehningen
GERMANY
declare under our responsibility that the product
Machine type Hand Grinder
Model Power Stripper
Order-No. 111 095 000
Serial-No. ______________________
Year of manufacture ______________________
comply with the EU-Directrives
Machinery directive 2006/42/EC
EMC directive 2004/108/EC
in accordance with with following standards
EN 12100-1:2003, EN 12100-2:2003
EN 60745-1
EN 61000-3-2, EN 61000-3-3
EN 55014-1, EN 55014-2
Date, _______________________
Signatory:
Heinrich Serediuk, Technical Dept.