Jar Furniture BEGA User manual

Assembly Instructions
BEGA
Dining Chair

1 2
Read Instructions carefully. Lay out all of the components on a soft surface
Check no parts are missing. as if you were preparing to do a jigsaw puzzle.
3 4
Carefully identify each component, especially Separate and identify each component from the
those that are similar. The most common mistake hardware pack and rest each one in its proper
is getting things back to front. location before fastening.
5 6
DO NOT fully tighten screws (leave slightly If glue is required DO NOT set until you are
loose). When the items is fully assembled certain that the parts belong together.
tighten the screws - but do not over tighten.
WARNING
FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE
THAT IS NOT COVERED BY YOUR WARRANTY
Page 2

What you Need
To Assemble the Body
1 x Allen Key
(provided)
(Tools not provided)
Phillips Head Screwdriver
Please make sure you have all these parts before you start.
Back Rest
(P1)
Page 3
2 x Short
Bolts
(H1)
4 x Medium
Bolts
(H2)
4 x Long
Bolts
(H3)
4 x Screws
(H6)
10 x Lock
Washers
(H4)
10 x Flat
Washers
(H5)
Seat Cushion
(P2)
Seat Frame
(P3)
Front Leg
(P4)

Step 1
You will need:
4 x Medium
Bolts
(H2)
4 x Lock
Washers
(H4)
4 x Flat
Washers
(H5)
Attach 1 x Lock Washers (H4) and 1 x Flat Washers (H5) into 1 x Medium Bolts (H2).
Insert 1 x Medium Bolts (H2) with Washers into holes of Front Corner Block as illustration shown.
Repeat the step for next 3 x Medium Bolts with Washers into another holes of Front Corner Block.
Do not fully tighten screws (leave slightly loose). When the items is fully assembled tighten the
screws - but do not over tighten.
Step 2
You will need:
2 x Short
Bolts
(H1)
2 x Lock
Washers
(H4)
2 x Flat
Washers
(H5)
Attach 1 x Lock Washers (H4) and 1 x Flat Washers (H5) into 1 x Short Bolts (H1).
Insert 1 x Short Bolts (H1) with Washers into holes of Back Seat Frame as illustrarion shown.
Repeat the step for next 1 x Short Bolts with Washers into another holes of Back Seat Frame.
Do not fully tighten screws (leave slightly loose). When the items is fully assembled tighten the
screws - but do not over tighten.
Page 4
(P4)
(P3)
(H4)
(H2)
(H5)
(P1)
(P3)
(P4)
(H4)
(H1)
(H5)

Step 3
You will need:
4 x Long
Bolts
(H3)
4 x Lock
Washers
(H4)
4 x Flat
Washers
(H5)
Attach 1 x Lock Washers (H4) and 1 x Flat Washers (H5) into 1 x Long Bolts (H3).
Insert 1 x Long Bolts (H3) with Washers into holes of Back Corner Block as illustration shown.
Repeat the step for next 3 x Long Bolts with Washers into another holes of Back Corner Block.
Do not fully tighten screws (leave slightly loose). When the items is fully assembled tighten the
screws - but do not over tighten.
Step 4
You will need:
4 x Screws
(H6)
Attach Seat Cushion (P2) onto Seat Frame (P3) and line it up.
Insert 1 x Screw (H6) through one of the hole of Seat Frame (P3).
Press the Seat Cushion (P2) tight as possible with one hand against the Seat Frame (P3).
Tighten the screw with a Phillips Head Screwdriver in another hand.
Insert 1 x Screw (H6) in one of the holes on the opposite side of the frame,
checking the traced lines to ensure the cushion is still in alignment with the frame.
Tighten the screw with the screwdriver.
Repeat Step 4 with the remaining screws.
Fully tighten all the screws and bolts when it is assembled on a flat surface.
Page 5
(H4)
(H3)
(H5)
(H6)
(P4)
(P3)
(P2)
(P1)
(P1)
(P3)
(P4)

Step 5
The job is now complete!
In the interest of our environment
Please dispose of all packaging thoughtfully.
Page 6