Jar Furniture KARLA User manual

Assembly Instructions
KARLA
Queen Size Upholstered Bed
Ver1.1

Page 2
2
3
56
Read Instructions carefully. Lay out all of the components on a soft surface
as if you were preparing to do a jigsaw puzzle.
Carefully identify each component, especially
those that are similar. The most common mistake
is getting things back to front.
Separate and identify each component from the
hardware pack and rest each one in its proper
WARNINGWARNING
Check no parts are missing.
4
fully tighten screws（leave slightly
loose).When the item is fully assembled
tighten the screws - but do not over tighten.
FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE
THAT IS NOT COVERED BY YOUR WARRANTY
If glue is required DO NOT set until you are
certain that the parts belong together.

What you Need
To Assemble the Body
(Tools not provided)
Phillips Head Screwdriver
Page 3
Please make sure you have all these parts before you start.
HEADBOARD
(P1)
FOOTBOARD
(P2)
CENTER RAIL
(METAL)
(P4)
METAL SUPPORT
LEG WITH
ADJUSTER
(P5)
BED LEG
(P7)
16 x CSK Screw
M4 x 20mm
(H7)
24 x CSK Screw
M4 x 30mm
(H8)
1 x Allen Key
M4
(H9)
1 x Allen Key
M5
(H10)
SIDE RAIL
(P3)
LVL SLATS
(P6)
10 x JCBC Screw
M6 x 50mm
(H3)
34 x Spring
Washer 5
16"
(H4)
24 x Flat Washer
5
16"
(H5)
16 x JCBC Screw
M6 x 30mm
(H2)
8 x JCBB Screw
M8 x 40mm
(H1)
10 x Flat
Washer 1
4"
(H6)

Page 4
Step 2
You will need:
8 x JCBC Screw
M6 x 30mm
(H2)
8 x Flat Washer 5
16"
(H5)
8 x Spring Washer
5
16"
(H4) (P1)
(P2) (P7)
(H2)
(H4)
(H5)
(H7)
(H9)
1 x Allen Key M4
(H9)
16 x CSK Screw
M4 x 20mm
(H7)
OPEN THE
NON-WOOVEN
COVER
TAKE OUT THE INNER BOX FOR THE
METAL LEG
Step 1
BACK VIEW
(P1)

Page 5
Step 4
You will need:
8 x JCBC Screw
M6 x 30mm
(H2)
8 x Spring Washer
5
16"
(H4)
8 x Flat Washer
5
16"
(H5)
1 x Allen Key M4
(H9)
(P2)
(P3)
(H9)
(H2)(H4)(H5)
(P4)
Step 3
You will need:
8 x JCBB Screw
M8 x 40mm
(H1)
8 x Flat Washer 5
16"
(H5)
(P1)
(P3)
(H5)
(H4)
(H10)
(H1)
1 x Allen Key M5
(H10)
8 x Spring Washer
5
16"
(H4)
(P1)
(P2)
(P3)

Page 6
SCREW THE SLAT
(H6)
(H4)
(H3)
(H9)
(P6)
Step 5
You will need:
4 x JCBC Screw
M6 x 50mm
(H3)
4 x Spring Washer
5
16"
(H4)
4 x Flat Washer 1
4"
(H6)
1 x Allen Key M4
(H9)
(H3) (H9)
(H4)
(H6)
(P5) (P4)
(P6)
Step 6
You will need:
6 x JCBC Screw
M6 x 50mm
(H3)
6 x Spring Washer
5
16"
(H4)
6 x Flat Washer 1
4"
(H6)
1 x Allen Key M4
(H9)

Page 7
COMPLETED ASSEMBLY
Step 7
You will need:
24 x CSK Screw
M4 x 30mm
(H8)
SCREW THE SLAT
(H8)
(P6)