Jaypro Sports LS-200 User manual

Rev-B Page 1of 12
-- LS-200 --
(THE PLAYGROUND)
Installation Instructions
Call Jaypro Sports Equipment at 1-800-243-0533
during regular business hours for technical support.
www.jaypro.com
!
!
WARNING
D O N O T A T T E M P T T O
A S S E M B L E T H I S S Y S T E M
W I T H O U T C A R E F U L L Y
READING AND FOLLOWING ALL
INSTRUCTIONS. BEG IN BY
IDENTIFYING AND TAKING
INVENTORY OF ALL PARTS
U S I N G

Rev-B Page 2of 12
JAYPRO SPORTS
LS-200RS THE PLAYGROUND
ITEM
QTY
IMAGE
DESCRIPTION
1
1
6” x 6” x 157-1/8” LONG SQUARE UPRIGHT POST
2
1
8-1/4” x 11” x 7/16” THICK BACK POST PLATE
3
1
5” x 5” x 78-3/8” LONG UPPER EXTENSION ARM
WITH 8-1/4” x 11” PLATE & 6” x 10-1/2” PLATE
4
1
2-3/4” x 2-3/4” x 32-5/8” LONG LOWER EXTENSION
ARM WITH 6” x 6-3/8” PLATE & 4-3/4” x 8-1/2” PLATE
ITEM
QTY
IMAGE
DESCRIPTION

Rev-B Page 3of 12
ITEM
QTY
IMAGE
DESCRIPTION
5
1
42” x 72” GLASS BACKBOARD
6
1
UNIVERSAL BREAKAWAY GOAL W/ NETTING &
RUBBER GASKET
7
1
GLASS BACKBOARD SUPPORT FRAME
8
1
PAIR OF BACKBOARD EDGE PADDING
ITEM
QTY
IMAGE
DESCRIPTION

Rev-B Page 4of 12
ITEM
QTY
IMAGE
DESCRIPTION
9
4
PVC RIM SPACER FOR BACKBOARD
10
6
M16 x 220 mm HEX BOLT
11
12
M16 WASHER
12
6
M16 LOCK WASHER
13
6
M16 HEX NUT
14
4
M10 x 70 mm HEX BOLT
15
8
M10 WASHER
16
4
M10 LOCK WASHER
17
4
M10 HEX NUT
ITEM
QTY
IMAGE
DESCRIPTION

Rev-B Page 5of 12
ITEM
QTY
IMAGE
DESCRIPTION
18
4
M8 x 30 mm HEX BOLT
19
8
M8 x 35 mm HEX BOLT
20
20
M8 WASHER
21
12
M8 LOCK WASHER
22
8
M8 HEX NUT
23
6
M6 x 30 mm HEX BOLT
24
12
M6 WASHER
25
6
M6 LOCK WASHER
26
6
M6 HEX NUT
27
6
M5.5 x 30 mm SELF-DRILLING HEX HD W. PLASTIC
WASHER
ITEM
QTY
IMAGE
DESCRIPTION
IMPORTANT NOTICE:
1) BEFORE EACH USE CHECK EQUIPMENT FOR PROPER CONNECTING
HARDWARE AND STRUCTURAL INTEGRITY. REPLACE DAMAGED OR
MISSING HARDWARE IMMEDIATELY.
2) USE OF THIS EQUIPMENT OTHER THAN INTENDED, MAY BE
HAZARDOUS.
3) ALTERATION OR MODIFICATION OF THIS EQUIPMENT MAY BE
HAZARDOUS AND RESULT IN INJURY. FOR REPAIR OR
REPLACEMENT, CONTACT YOUR DEALER OR JAYPRO SPORTS.

Rev-B Page 6of 12
BEFORE YOU START
A. Identify and inventory all parts using the checklist boxes that appear on each
page. Be sure to keep the hardware bags and their contents separate. If any
parts are missing call Our Customer Service Department (800-243-0533).
1. 2 Adjustable Wrenches 10. Concrete-1/2 yard or 14-16
2. Socket Set Bags, (80 lb. bags)
3. 9/16" Wrench 11. Phillips Head Screwdriver
4. 3/4" Wrench 12. Electric Drill
5. 15/16" Wrench 13. Carpenter's Level
6. 1/2" Wrench 14. A minimum of 2 Ladders
7. Hammer or Mallet 15. Water Supply
8. Tape Measure 16. Degreaser
9. Shovel 17. 1/4” Drill Bit
SUGGESTED TOOLS AND MATERIALS FOR ASSEMBLY
(Not Included)
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY
OR PROPERTY DAMAGE AND WILL VOID THE WARRANTY.
●Proper and complete assembly, use and supervision is essential for proper operation and
to reduce the risk of accident or injury. A high probability of serious injury exists if this
system is not installed, maintained, or operated properly.
●The major components of this system have considerable weight. It is recommended that
scaffolding or a lift jack be used to hoist the outrigger, frames and board into place.
●If using a ladder during assembly, use extreme caution. Follow all warnings and cautions
on the ladder carefully.
●Before digging, contact the appropriate agency to locate underground power cables, gas,
and water lines. Do not install the system within 20 feet of overhead power lines.
●Climate, corrosion, or misuse could result in system failure.
●If technical assistance is required, contact the manufacturer.
●Most injuries are caused by misuse and /or failure to follow instructions.
●Use caution when using the system.
!
!
SAFETY INSTRUCTIONS

Rev-B Page 7of 12
Footing:
NOTE: Before digging, call to locate any buried utility lines.
a. Dig a hole 54" deep x 36" across. The edge of the hole should be flush with the
edge of the playing surface. If you live in an area where heavy frost can occur, it
may pose a problem, consult your local building inspector to determine the
appropriate hole depth. NOTE: The hole must be at least 54" deep.
b. There must be at least 3 feet of clearance behind the unit to enable the user to
adjust the height.
c. Mix the concrete according to the instructions on the bags. Note that a thicker mix
of concrete will dry stronger than a thin mix. Pour the concrete into the hole,
stopping approximately 18 inches from the top of the hole.
d. Insert the basketball post 48 inches deep.
e. Insert the four pieces of 3/4” x 42” Rebar into the hole, pushing each piece firmly
to the bottom of the hole. The four pieces should be arranged in a square
approximately 8 - 9 inches wide so that each piece of rebar will be positioned
surrounding the backstop post.
f. Finish filling the hole to the top with concrete.
g. Allow the concrete to cure a minimum of 72 hours before proceeding. In humid
climates or wet weather, allow additional time for the concert to cure.

Rev-B Page 8of 12
Extension assembly:
a. Attach the back post plate to the upper extension arm and position it just beneath
the white stripe.
b. Attach the lower extension arm to the upper extension arm, assembly as shown.
c. Carefully adjust the height of the extension arm assembly so that the height of the
top slot of the lower extension arm is 119” (see next page for illustration).
d. Securely tighten all hardware.

Rev-B Page 9of 12

Rev-B Page 10 of 12
Backboard & Goal Rim Assembly:
a. Insert six (6) M6 x 30 mm hex bolt into extension arm / support upright and
secure with M6 washer, lock washer and hex nut.
b. Slide the glass backboard into the support channel and secure with M8 x 35 mm
hex bolt with washer, lock washer and hex nut.
c. Removed goal cover plate before inserting M10 x 70 mm hex bolt with washer.
The rim spacer and rim gasket goes between glass backboard and goal. Secure in
place M10 with washer, lock washer and hex nut.
d. Use a drill to secure edge padding to glass backboard with M5.5 x 30 mm self-
drilling hex head with plastic washer.

Rev-B Page 11 of 12

Rev-B Page 12 of 12