Jaypro Sports 400-AC-FG Quick start guide

1
FIXED HEIGHT BASKETBALL SYSTEM
ASSEMBLING INSTRUCTIONS
AND OWNER'S MANUAL
Keep this instruction manual in case you have to contact the manufacturer for replacement parts.
!
!
WARNING
FAIL U R E T O C O M P L Y W I T H A N Y
O F T H E W A R N I N G S I N T H E S E
I N S T R U C T I O N S M A Y R E S U L T I N
S E R I O U S P E R S O N A L I N J U R Y .
FAILURE TO COMPLY MAY ALSO
R E S U L T I N P R O P E R T Y D A M A G E .
PLEASE HEED ALL WARNINGS AND
CAUTIONS TO ENSURE YOUR SAFETY.
DO NOT ATTEMPT TO ASSEMBLE THIS
S Y S T E M W I T H O U T C A R E F U L L Y
R E A D I N G A N D F O L L O W I N G A L L
I N S T R U C T I O N S . B E G I N B Y
I D E N T I F Y I N G A N D T A K I N G
INVE NT O RY OF A LL PART S USI NG
T H E P A R T S L I S T P R O V I D E D .
400-AC-FG
400-FA-FG
Item #

2
1. 2 Adjustable Wrenches 10. Concrete-1/2 yard or 14-16
2. Socket Set Bags, (80 lb. bags)
3. 9/16" Wrench 11. Phillips Head Screwdriver
4. 3/4" Wrench 12. Electric Drill
5. 15/16" Wrench 13. Carpenter's Level
6. 1/2" Wrench 14. A minimum of 2 Ladders
7. Hammer or Mallet 15. Water Supply
8. Tape Measure 16. Degreaser
9. Shovel 17. 1/4" Drill Bit
TOOLS AND MATERIALS REQUIRED FOR ASSEMBLY
(Not Included)
**A MINIMUM OF SIX ADULTS IS
REQUIRED TO LIFT UNIT INTO PLACE**
STOP!
BEFORE YOU START
A. Identify and inventory all parts using the checklist boxes in the parts list. Be sure to
Keep the hardware bags and their contents separate. If any parts are missing call
Ourt Customer Service Department (800-243-0533).
B. Test fit all Bolts by inserting them into the respective hole. If necessary, carefully
Scrape away any excess powder coating buildup from inside the holes. Do not
Scrape away all of the powder coating. Bare metal may rust.
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE
AND WILL VOID THE WARRANTY. The owner must ensure that all players know and follow these rules to safely operate the
system. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk
of accident or injury. A high probability of serious injury exists if this system is not installed, maintained, or operated
properly.
●If using a ladder during assembly, use extreme caution. Follow all warnings and cautions on the ladder carefully. ●6 people
are required to lift the unit into place. ●Before digging, contact the appropriate agency to locate underground
power cables, gas, and water lines. Do not install the system within 20 feet of overhead power lines. ●Climate, corrosion,
or misuse could result in system failure. ●If technical assistance is required, contact the manufacturer. ●Minimum
operational height is 7'6”to the Rim. Most injuries are caused by misuse and /or failure to follow instructions.
Use caution when using the system.
STOP!
!
!
SAFETY INSTRUCTIONS

3
Required For This Page:
Shovel, Concrete, Rebar and Tape Measure
**ONLY MINIMUM OF TWO ADULT IS REQUIRED FOR THE FOLLOWING STEPS**
NOTE: Before digging, call to locate any buried utility lines.
a. Dig a hole 54" deep and 36"x 36" square. The edge of the hole should be
flush with the edge of the playing surface. If you live in an area where
heavy frost can occur, it may pose a problem, consult your local building
inspector to determine the appropriate hole depth.
NOTE: The hole must be at least 54" deep.
b. Build a form before pouring the concrete pad, to ensure that the top of the
concrete remains straight and square. The form should be placed about
1/2" above the playing surface to allow for water drainage.
c. Bell out the bottom of the hole. And place the foundation using crush
stone, concrete pad or bricks that is 6 inches tall.
NOTE: A square hole prevents the rotation of the concrete.
NOTE: The area behind the playing surface must be cleared off by at least
3 feet to enable the user to stand behind the pole to adjust the Rim height.
STEP A
24”
54”
24”
STEP B
a. Mix the concrete according to the instructions on the bags. Note that a
thicker mix of concrete will dry stronger than a thin mix. Pour the concrete
into the hole, stopping approximately 18 inches from the top of the hole.
b. Insert the basketball post 48 inches from the playing surface
c. Insert the four pieces of ¾” x 42” Rebar into the hole, pushing each piece
firmly to the bottom of the hole. The four pieces should be arranged in a
square approximately 8 inches wide so that each piece of rebar will be
positioned surrounding the backstop post.
d. Finish filling the hole to the top with concrete. The top of the concrete
should reach just above the level of the top of the form.
YOU ARE NOW FINISHED WITH THE INITIAL ASSEMBLY STEPS. DO
NOT PROCEED WITH THE ASSEMBLY UNTIL THE CONCRETE HAS
FULLY CURED. CURING WILL TAKE A MINIMUM OF 72 HOURS. IN
HUMID CLIMATES OR WET WEATHER , ALLOW ADDITIONAL TIME
FOR THE CONCRETE TO CURE.
!
NEVER USE THE SYSTEM WITHOUT FOLLOWING THE CEMENTING INSTRUCTIONS. FAILURE TO FOLLOW ALL OF THESE INSTRUCTIONS
AND WARNINGS COULD LEAD TO SERIOUS PERSONAL INJURY OR PROPERTY DAMAGE AS LISTED ON PAGE ONE.
!
WARNING

4
Required For This Page:
•HEX HEAD BOLT APPROXIMATELY 6” - 7” LONG WITH
WASHERS, LOCK WASHERS AND HEX NUT. (SET OF 6)
•BACK POST PLATE
•EXTENSION ARM WELDMENT
•HEX HEAD BOLT APPROXIMATELY 3” LONG WITH
WASHERS, LOCK WASHERS AND TWO HEX NUT. (SET OF 4)
!
!
WARNING
*BECAUSE OF THE SIZE AND WEIGHT OF THE SYSTEM, A MINIMUM OF
THREE ADULTS ARE REQUIRED FOR THE FOLLOWING STEPS*
a. Assemble the 5 inch by 5 inch hole pattern backboard to extension arm weldment 5 inch by 5 inch hole pattern.
b. Using the 4 sets of hex head bolt that fits the 5 inch by 5 inch hole pattern. Order of main part is rim, gasket,
backboard and extension arm weldment, tie four items using the hex head bolt with washer thru rim and gasket.
Into the backboard nut in the 5 inch by 5 inch hole pattern, use a hex nut to hold the rim and gasket to the
backboard. Then lift the backboard on to the extension arm weldment 5 inch by 5 inch hole pattern. Finish this
off with washers, lock washers and hex next, repeat till all four set of hardware is securely on ( see figure 1&2).
STEP 1
a. Position the extension arm and back post plate to the post near the white
stripe.
b. Using the longest hex head bolt to tie the two item mention above using
the hardware as shown below. DO NOT OVER TIGHTEN!
c. Set the top holes in the plate to 119 inch to the playing surface.
STEP 2
119” TOP HOLES TO PLAYING SURFACE

5
Figure 1 (Rectangualar Backboard)
Figure 2 (Fan Backboard)

6
a. Assemble support arms to extension arm weldment. Note slots in support arms goes on the extension arm
weldment and holes on the other end goes for the backboard hardware.
STEP 3
Required For This Page: (Optional For Rectangular Backboard)
•HEX HEAD BOLT APPROXIMATELY 6” LONG WITH WASHERS, LOCK
WASHERS AND HEX NUT. (SET OF 1)
•SUPPORT ARMS (SET OF 2)
•HEX HEAD BOLT APPROXIMATELY 3” LONG WITH TWO WASHERS,
BLACK FENDER WASHER AND LOCK NUT. (SET OF 4)
(Optional For Rectangular Backboard) Note: The Fan Shape Backboard does not require braces.
Backboard and Support arm
Extension arm weldment and Support arm
Two backboards can be assembled on a pole as shown.

7
Required For This Page: (Optional For Rectangular Backboard)
•SELF-DRILLING HEX HEAD W/ PLASTIC WASHERS QTY: 10
•PLASTIC CAPS QTY: 10
•SAFETY PADS (OPTIONAL)
Electric Drill
a. Position the backboard pad to the backboard. Use drill to secure the self-drilling hex head w/ plastic washers on
the backboard frame. Use plastic caps to cover up the expose end the self-drilling hex head w/ plastic washers.
b. Now go back and tighten down the remaining hardware.
c. OPTIONAL put the base safety pad on before trying to put on the longer safety pad.
STEP 4
Corporate Office: 976 Hartford Turnpike Waterford, CT 06385
Tel: [phone] Fac: [phone]
www.jaypro.com
*If you hace any problems with your basketball system please contact us*
(Optional For Rectangular Backboard)