Jaypro Sports PVB-1250 User manual

Rev: A Page 1of 6
-- PVB-1250 --
Installation Instructions
Call Jaypro Sports Equipment at 1-800-243-0533
during regular business hours for technical support.
www.jaypro.com

Rev: A Page 2of 6
PVB-1250
PARTS LIST (QTY: SINGLE UNIT)
ITEM IMAGE DESCRIPTION QTY
1
COLLEGIATE VOLLEYBALL NET
P/N: PVBN-3 1
2
VOLLEYBALL UPRIGHT PADS
P/N: PVB-60P 1
3
VOLLEYBALL ANTENNA
P/N: VBA-80
1
4
ANCHOR END CLAMP COLLAR
P/N: PVB-13-7 1
5
TOP ROLLER CLAMP COLLAR
P/N: PVB-13-8 1
6
BOTTOM SLIDING COLLAR
P/N: PVB-13-9 2
7
3 1/2” OD UPRIGHT
P/N: VB-12U 2
8
WINCH w/ HARDWARE
P/N: PVBWINCH 1
9
3/8”-16 x 4 1/4" BUTTON HEX SCREW
PART OF PVBWINCH HARDWARE KIT 1
10
3/8” ACORN NUT
PART OF PVBWINCH HARDWARE KIT
1
11
3/8” x 4 CARABINER
P/N: HM5019 1
12
1/4” x 24” LONG CHAIN
P/N: CN0001 1
13
PVC TENSIONING HANDLE
PART OF PVBN-3 1
ITEM IMAGE DESCRIPTION QTY

Rev: A Page 3of 6
Table of Contents
IMPORTANT NOTICE:
1) BEFORE EACH USE CHECK EQUIPMENT FOR PROPER CONNECTING
HARDWARE AND STRUCTURAL INTEGRITY. REPLACE DAMAGED OR
MISSING HARDWARE IMMEDIATELY.
2) NEVER ALLOW ANYONE TO CLIMB OR HANG ON THE NET OR GOAL
FRAME. AS SERIOUS INJURY OR DAMAGE TO THE EQUIPMENT MAY
OCCUR.
3) USE OF THIS EQUIPMENT OTHER THAN INTENDED, MAY BE
HAZARDOUS.
4) ALTERATION OR MODIFICATION OF THIS EQUIPMENT MAY BE
HAZARDOUS AND RESULT IN INJURY. FOR REPAIR OR
REPLACEMENT, CONTACT YOUR DEALER OR JAYPRO SPORTS.
Tools Require:
1
Adjustable Wench
1
9/16” Box / Socket Wench
1
Tape Measure
oUnpack all parts and check against parts list to ensure that all have been
included.
oInspect all parts for damage. Report any damages to the trucking
company.
These instructions assume that the appropriate ground sleeves have been correctly
installed:
• The PVB-1250 will fit most 2’’ inner diameter ground sleeves.
• The inside bottom surface of the ground sleeves must be at least 8” below floor level.
Please consult the instructions and specifications supplied with your ground sleeves for
more information.
If you require additional information or support to install or operate your volleyball
system, please contact the Jaypro Sports customer support team, Monday through Friday,
8:30AM to 5:00 PM (EST), at 1-800-243-0533.

Rev: A Page 4of 6
Assembly Instructions:
1. Place the uprights onto a table or pair of saw horses and loosely assemble the
parts as shown.
2. One upright will be designated the Winch End Upright and the other the Anchor
End Upright.
3. Assemble the winch onto one of the uprights as shown.
4. Carefully slide the bottom sliding collar and top roller collar onto the winch end upright.
Align the roller collar with winch assembly and tighten.
5. Carefully slide both a bottom sliding collar and anchor end collar over the anchor end
upright. Do not over tighten the clamping bolts as further adjustment will be required.
6. Place uprights in preinstalled sleeves (see instructions included with sleeves for their
installation).
7. Adjust the heights of the collars to the specific activity to be played. The top edge of the
top collars should be placed about ¾” above the desired height of the net. The bottom
collars should be positioned about 39” below the top collars.
8. Ensure both side dowels are inserted in the side net binding. Position the net between the
2 uprights.
9. Thread the webbing strap from the winch over the roller clamp and connect the end of
the cable to the snap buckle. Connect the other end of the net to a carabiner and the
length of chain provided and attach that end of the chain to the top anchor end clamp
(step 5) with the other carabiner.
10. Adjust the length of the chain as necessary to center net on court.
11. Slowly tension the top webbing strap by cranking the winch with the winch
handle. Adjust chain as necessary to keep the net centered.
12. Verify net heights and net centering. The uprights will deflect inward and downward due
to net tension; you may need to adjust heights and /or re-center the net.
Warning: Release tension from
the net before loosening any
hardware from the uprights.

Rev: A Page 5of 6
Winch End Upright
Typical Upright
Anchor End Upright
TIE A LOOP KNOT
BOTTOM SLIDING COLLAR
ITEM #6
COLLEGIATE VOLLEYBALL NET
ITEM #1
BOTTOM SLIDING COLLAR
ITEM #6
TIE A KNOT
COLLEGIATE VOLLEYBALL NET
ITEM #1
PVC TENSIONING HANDLE
ITEM #13

Rev: A Page 6of 6
Assembly Instructions:
13. Raise the center of the net to the full official net height by cranking the handle. Adjust all
net side straps to further tension the net.
14. When releasing tension on the net, first unfasten the side straps and release tension on the
bottom cord, and then slowly release tension of the top cable.
15. To remove the unit for storage, disconnect the net from the 2 uprights and carefully lift
each upright from the floor sleeve.
16. For player safety cut any excess chain before putting system into service.
INSTALLATION AND USE CONSIDERATIONS
1) The unit is designed for high level competition play. Consequently, when installed
and operational, the unit is subject to considerable stress loads. It is essential to inspect
all parts before each use.
2) Do not use this equipment without the protective upright padding properly fastened in place.
Tennis:
Badminton:
VELCRO STRAPS
VOLLEYBALL
ANTENNA
NET DOWELS
(BOTH ENDS)
NOTE: SAG, ADJUST BY PLACING
THE TOP COLLARS ¾” HIGHT
THAN DESIRED NET HEIGHT.
Volleyball:
7’ 11 5/8” (2.43 m) Men’s
7’ 4 1/8” (2.24 m) Women’s
5’
(1.52 m)
3’-6”
(1.07 m)
Warning: Release tension from
the net before loosening any
hardware from the uprights.