Jaypro Sports SP4 User manual

Rev-B Page 1of 7
-- SP4 --
(SHOULDER PAD)
Installation Instructions
Call Jaypro Sports Equipment at 1-800-243-0533
during regular business hours for technical support.
www.jaypro.com

Rev-B Page 2of 7
SP4
PARTS LIST (QTY: SINGLE UNIT)
ITEM
IMAGE
DESCRIPTION
QTY
1
BOTTOM UPRIGHT
(w/ WHEEL MOUNTS)
2
2
BOTTOM UPRIGHT
2
3
TOP UPRIGHT
4
4
SIDE PLATE 1
2
5
SIDE PLATE 2
(PLATE w/ LOGO CUTOUT)
2
6
WHEEL
(IMAGE MAY DIFFER FROM WHAT’S SHOWN)
4
7
#8 x 12” PAN HEAD PHILIP SCREW
8
8
5/16”-18 x 2” LONG BUTTON HD SCREW
(IMAGE MAY DIFFER FROM WHAT’S SHOWN)
16
9
5/16”-18 x 1” LONG BUTTON HD SCREW
(IMAGE MAY DIFFER FROM WHAT’S SHOWN)
4
10
5/16”-18 THIN NYLON LOCK NUT
(IMAGE MAY DIFFER FROM WHAT’S SHOWN)
20
ITEM
IMAGE
DESCRIPTION
QTY

Rev-B Page 3of 7
Table of Contents
I. Assembly One Half: ........................................................................................................ 4
II. Assemble Both Halves:.................................................................................................. 6
III. Install Wheels: .............................................................................................................. 7
IMPORTANT NOTICE:
1) BEFORE EACH USE CHECK EQUIPMENT FOR PROPER CONNECTING
HARDWARE AND STRUCTURAL INTEGRITY. REPLACE DAMAGED OR
MISSING HARDWARE IMMEDIATELY.
2) NEVER ALLOW ANYONE TO CLIMB OR HANG ON THE FRAME. AS
SERIOUS INJURY OR DAMAGE TO THE EQUIPMENT MAY OCCUR.
3) USE OF THIS EQUIPMENT OTHER THAN INTENDED, MAY BE
HAZARDOUS.
4) ALTERATION OR MODIFICATION OF THIS EQUIPMENT MAY BE
HAZARDOUS AND RESULT IN INJURY. FOR REPAIR OR
REPLACEMENT, CONTACT YOUR DEALER OR JAYPRO SPORTS.
Tools Require:
1
Allen Wench Set
1
1/2" Socket or Adjustable Wench
1
Philips Screw Driver
oUnpack all parts and check against parts list to ensure that all have been
included.
oInspect all parts for damage. Report any damages to the trucking
company.

Rev-B Page 4of 7
I. Assembly One Half:
Figure 1
Figure 2
INSIDE UPRIGHT
(LOGO TO FACE OUTWARD)
SIDE PLATE 1
(FLANGE)
SIDE PLATE 2
(w/ LOGO CUTOUT)
5/16”-18 x 2” LONG BUTTON HD SCREW
OUTSIDE UPRIGHT
(LOGO TO FACE OUTWARD)
#8 x 12” PAN HEAD
PHILIP SCREW
TOP UPRIGHT
BOTTOM UPRIGHT
(w/ WHEEL MOUNTS)
5/16”-18 THIN NYLON LOCK NUT
SIDE PLATE & UPRIGHT
NOTE ORIENTATION OF SIDE PLATE FLANGES.

Rev-B Page 5of 7
Figure 3
1) Assemble side plate 1 and side plate 2 onto two uprights in place using 5/16”-18 x
2” long button head screws (as shown in Figure 1). Ensure that both upright logo
faces the same direction and both side plate flanges are on the same side.
2) Using 5/16”-18 thin nylon lock nut. To secure side plates to the uprights onto
eight places (as shown in Figure 2).
3) Repeat steps again to create another set (Figure 3).

Rev-B Page 6of 7
II. Assemble Both Halves:
Figure 4
Figure 5
1) Orientate both halves of cart back to back (Figure 4) and line up the holes in the
side plate flange.
2) Secure both halves together using 5/16-18 x 1” long button head screw and 5/16”-
18 thin nylon lock nut (as shown in Figure 5).
5/16”-18 THIN NYLON LOCK NUT
SIDE PLATE
5/16”-18 x 1” LONG BUTTON HEAD SCREW

Rev-B Page 7of 7
III. Install Wheels:
Figure 6
1) Carefully lay the entire frame onto its side.
2) Thread four wheels by hand onto the outside uprights.
Please note only two of the uprights accept wheels.
OUTSIDE UPRIGHT
(w/ WHEEL MOUNTS)
WHEEL