Jaypro Sports A12-568 User manual

1/17 Page 1of 14
-- FBSC-120 --
(ECONOMY FOOTBALL / SOCCER GOAL)
Installation Instructions
Call Jaypro Sports Equipment at 1-800-243-0533
during regular business hours for technical support.
www.jaypro.com

1/17 Page 2of 14
JAYPRO SPORTS
ECONOMY FOOTBALL / SOCCER GOAL
ITEM
IMAGE
DESCRIPTION
QTY
1
UPRIGHT
2
2
UPRIGHT BACKING
PLATE
2
3
2”x 2”BLACK SQUARE
TUBE CAP
2
4
2”x 4”BLACK SQUARE
TUBE CAP
2
5
FOOTBALL UPRIGHT
2
6
LADDER FRAME
2
7
1/2”-13 HEX NUT
13
ECONOMY FOOTBALL / SOCCER GOAL PARTS LIST CONTINUE NEXT PAGE

1/17 Page 3of 14
8
1/2”SPLIT LOCK WASHER
13
9
1/2”FLAT WASHER
26
10
1/2”-13 x 6”HEX HD CAP
SCREW, ZP
6
11
1/2”-13 x 5 1/2”HEX HD
CAP SC, ZP
4
12
1/2"-13 x 2”HX HD CAP SC,
ZP
3
13
3/8”-16 x 3”HEX HEAD
CAP SCREW ZP
4
14
3/8”SAE FLAT WASHER,
ZP
8
15
3/8”-16 THIN NYLON LOCK
NUT NTE, ZP
4
16
NET CLIPS w/ SELF
DRILLING SCREW
1
ECONOMY FOOTBALL / SOCCER GOAL PARTS LIST

1/17 Page 4of 14
JAYPRO SPORTS
OPTIONAL EUROPEAN BACKSTAY KIT
ITEM
IMAGE
DESCRIPTION
QTY
1
HUB WELDMENT
4
2
EUROPEAN STYLE
PIPE
2
3
3/8"-16 x 2 1/2" HEX
HEAD CAP SCREW, ZP
4
4
3/8"-16 THIN NYLON
LOCK NUT NTE, ZP
8
5
3/8" SAE FLAT
WASHER, ZP
16
6
3/8"-16 x 3" HEX HEAD
CAP SCREW ZP
4
Call Jaypro Sports Equipment at 1-800-243-0533
during regular business hours for technical support.
www.jaypro.com
MODEL #: FBSC-EBS
EUROPEAN BACKSTAYS: Removable backstays are
made of 1.66" OD galvanized steel tubing.

1/17 Page 5of 14
JAYPRO SPORTS
OPTIONAL EUROPEAN BACKSTAY KIT
ITEM
IMAGE
DESCRIPTION
QTY
1
HUB WELDMENT
2
2
1.66" DIA BACKSTAY
BRACE
2
3
3/8-16 x 2 1/2 HEX
HEAD CAP SCREW, ZP
2
4
3/8"-16 THIN NYLON
LOCK NUT NTE, ZP
2
5
3/8" SAE FLAT
WASHER, ZP
4
6
GROUND STAKE
2
Call Jaypro Sports Equipment at 1-800-243-0533
during regular business hours for technical support.
www.jaypro.com
MODEL #: FBSC-FBS
FULL BACKSTAYS: Removable backstays are made of
1.66" OD galvanized steel tubing.

1/17 Page 6of 14
IMPORTANT NOTICE:
1) BEFORE EACH USE CHECK EQUIPMENT FOR PROPER CONNECTING
HARDWARE AND STRUCTURAL INTEGRITY. REPLACE DAMAGED OR
MISSING HARDWARE IMMEDIATELY.
2) NEVER ALLOW ANYONE TO CLIMB OR HANG ON THE NET OR GOAL
FRAME. AS SERIOUS INJURY OR DAMAGE TO THE EQUIPMENT MAY
OCCUR.
3) USE OF THIS EQUIPMENT OTHER THAN INTENDED, MAY BE
HAZARDOUS.
4) ALTERATION OR MODIFICATION OF THIS EQUIPMENT MAY BE
HAZARDOUS AND RESULT IN INJURY. FOR REPAIR OR
REPLACEMENT, CONTACT YOUR DEALER OR JAYPRO SPORTS.
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED:
(1) 9/16” Socket Wrench and Box Wrench
(1) 3/4” Socket Wrench and Box Wrench
(1) #29 Drill Bit or 9/64” Drill Bit or 3.5 mm Drill Bit
(1) Phillips head Power Drill
Unpack all parts and check against parts list to ensure that all have been
included.
Inspect all parts for damage. Report any damages to the trucking
company.

1/17 Page 7of 14
Site prep:
1. Determine the proper location for the goal uprights on the playing field. The spacing
between uprights is 24’-4” center to center. Dig the footing holes to the dimensions as
shown on the illustration below. These are minimum suggested dimensions for
average soil conditions.
2. For best results assemble the lower goal frame; uprights and crossbar assembly on the
ground prior to placing in the footing.
Semi-permanent installation: SGP-722G ground sleeve sold separately
1. Note: Whenever goal is removed from ground sleeves for maintenance or storage,
always cover the open end of the sleeve using the top cap provided.
2. Install ground sleeves as shown in drawing SGP-722G. Ground sleeves may be
installed with or without using the goal frame itself.
3. If using goal frame to install sleeve in. Slide the sleeves onto the bottom of each
upright and lower the assembled goal into the footing. Be careful to ensure that
concrete does not enter the sleeve –recommend wrapping tape around goal upright &
top of sleeve. Make sure the distance between the underside of the soccer crossbar
and the playing surface measures 8 FT. Brace the structure to assure that it doesn’t
shift during curing process.
4. Wait for the concrete to fully cure according to the manufacturer’s instructions. (A
minimum of 48 hours)
Permanent installation:
1. Lower the assembled goal (see frame assembly instructions) into the footing. Pay
special attention to proper orientation with regards to the face side. Block beneath and
around each upright, plumb the structure and pour the concrete. Check that the
distance between the playing surface and the crossbar of the upright is 8’. Brace the
structure to assure that it does not shift during the footing curing process.
2. Wait for the concrete to fully cure according to the manufacturer’s instructions. (A
minimum of 48 hours)
Note these are suggested dimensions for average soil conditions,
consult local building codes.
6” of crush stone, block or concrete footing.

1/17 Page 8of 14
Soccer Net Money Clip installation: (Nets sold separately)
1. Drill pilot holes for money clip if using soccer net with football/soccer goal frame.
2. Layout ladder frame and determined the orientation before drilling holes on one side
only. Holes are space at 14” on center, expert for ends. Same goes for the upright.

1/17 Page 9of 14

1/17 Page 10 of 14
Corner goal frame installation:
1. Use 6” long hex head screw thru upright backing plate, upright and ladder frame.
Make sure your ladder frame matches the image shown below.