Jazwares Fortnite The Baller User manual

THE BALER
CNTS:
INSTRUCION MAUL
8+
FNT0381
Made in China
Used with permission. Manufactured and Distributed by:
Jazwares, LLC, Sunrise, FL 33326, USA
Jazwares, 16A Crane Grove, London, N7 8LE, United Kingdom
Jazwares GmbH, Mina-Rees-Str. 8, 64295 Darmstadt, Germany
www.jazwares.com / www.jazwares.de
© 2020 Epic Games, Inc. Fortnite and its logo are registered trademarks of
Epic Games, Inc. in the USA (Reg. U.S. Pat. & Tm. O.) and elsewhere.
All rights reserved.
FCC ID: YNIJAZWARES381 FCC ID: YNIJAZWARES117
“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.”
WARNING! Changes or modications not expressively approved by the manufacturer responsible for compliance could void the user’s authority to
operate the equipment.”
NOTE:“This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:“
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Conforms to toy safety standards CPSIA, ASTM-F963 and EN71.
HOW TO CLEAN YOUR
BALLER DELUXE VEHICLE
• To clean, wipe with a dry cloth.
• Do not submerge in water.
• Do not use chemical or abrasive cleaners.
BATTERY WARNINGS:
1. Batteries are to be replaced by an adult.
2. Non-rechargeable batteries are not to be recharged.
3. Rechargeable batteries are to be removed from the toy before being charged.
4. Rechargeable batteries are only to be charged under adult supervision.
5. For best performance, only the recommended batteries or their equivalent are to
be used.
6. Batteries must be inserted with correct polarity.
7. Do not mix new and used batteries.
8. Do not mix dierent types of batteries.
9. Exhausted batteries are to be removed from the toy.
10. The supply terminals are not to be short-circuited.
HYBRID
(STAGE 2)
THE BALER
REMOT
CNTROL

ADJUSTING STERING ALINMET
RANGE OF PLAY: 25 METERS/82 FEET.
CONTROLLER FREQUENCY BAND ：2410 MHz - 2473 MHz，MAXIMUM POWER：1.56 mW
RECEIVER FREQUENCY BAND ：2410 MHz - 2473 MHz，MAXIMUM POWER：0.06 mW
TROUBLSHOTING
TO ADJUST STEERING ALIGNMENT
If the vehicle doesn’t run straight
forward, adjust the steering alignment
lever on the underside of the vehicle.
STEERING
ALIGNMENT
LEVER
PEG FEET ONTO
PEDALS
ATTACH HANDS
TO HANDLES
STEERING DIAL
ON / OFF
FIGURE PLACEMNT
BATERY PLACEMNT
TOP VIEW
TWIST THEN PULL
TO REMOVE CAP.
REMOVE SEAT TO ACCESS
BATTERY COMPARTMENT.
OPEN AND CLOSE BATTERY
COVER WITH A PHILLIPS
SCREWDRIVER. NOT INCLUDED
BATTERY
COMPARTMENT
3
AFTER INSERTING BATTERIES,
CLOSE THE BATTERY
COMPARTMENT. PEG THE SEAT
BACK ONTO THE BASE, AND
PUT THE CAP ONTO THE
VEHICLE.
4
2
1
HOW T PAIR
1. Turn the vehicle ON, then turn the transmitter
controller ON within 30 seconds.
*Do not press any buttons or switches on the
controller while pairing, this may cause
interference.
2. The LED light on controller will start blinking.
3. Once the pairing is successful, the LED light on
controller will stop blinking and stay on.
4. If pairing is unsuccessful, turn the vehicle and
controller OFF and try again.
5. If vehicle enters sleep mode, turn the vehicle
and controller o, then back on and try again.
REMOT CNTROLE
MOVE UP:
TO GO
FORWARD
FOR TURNS:
MOVE SIDE
TO SIDE
ON / OFF
BATTERY
COMPARTMENT
MOVE DOWN:
TO GO
BACKWARD
Open and close the battery cover
with a Phillips screwdriver
LED LIGHT POWER
INDICATOR
1A
1B
1.5V AAA (LR03)
1.5V AAA (LR03)
Vehicle will not START
Vehicle does not respond to controls
Vehicle does not drive straight
Vehicle does not move
Vehicle does not respond properly
Transmitter controller does not work
PROBLEM SOLUTION
1. Power switch is o. Make sure to turn it on.
2. Batteries are installed with incorrect polarities. Check the + and - markings to make sure the
batteries are properly aligned.
3. Batteries are drained. Charge batteries, then re-install or install new batteries.
If the controller light is o, its batteries are drained. Replace the controller batteries.
The vehicle is likely out of range. Bring controller closer to the vehicle. If problem persists,
remove the controller batteries and replace with new batteries, then restart (ON/OFF) the vehicle.
1. Stop operation, switch o the power and rest your vehicle for a few minutes.
2. Check the position of the batteries in the vehicle, they may have been knocked loose during play.
1. Adjust the steering dial underneath the front axle, left or right, until the wheels point
straight forward.
1. Transmitter controller battery is drained. Replace the controller battery.
2. Vehicle is out of range. Bring controller closer to the vehicle.
3. Interference from surrounding electrical machinery. Bring to a wide open space.
REQUIRES BATTERIES, BATTERIES NOT INCLUDED.
THE PRODUCTS CAN BE SOLD IN ALL EU COUNTRIES