JBL Harman PARTYBOX 110 User manual

PARTYBOX 110
OWNER’S MANUAL

22
IMPORTANT SAFETY INSTRUCTIONS
For all products:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Clean only with a dry cloth.
6. Do not block any ventilation openings. Install this apparatus
in accordance with the manufacturer’s instructions.
7. Do not install this apparatus near any heat sources such as
radiators, heat registers, stoves or other apparatus (including
ampliers) that produce heat.
8. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding-type plug has two
blades and a third grounding prong. The wide blade or
the third prong is provided for your safety. If the provided
plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
9. Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles and the point
where they exit from the apparatus.
10. Use only attachments/accessories specied by the
manufacturer.
11. Use only with the cart, stand, tripod, bracket
or table specied by the manufacturer or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
12. Unplug this apparatus during lightning storms or when
unused for long periods of time.
13. Refer all servicing to qualied service personnel. Servicing
is required when the apparatus has been damaged in
any way, such as when the power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into
the apparatus, or the apparatus has been exposed to rain or
moisture, does not operate normally or has been dropped.
14. To disconnect this apparatus from the AC mains completely,
disconnect the power- supply cord plug from the AC
receptacle.
15. The mains plug of the power-supply cord shall remain readily
operable.
16. This apparatus is intended to be used only with the power
supply and/or charging cable provided by the manufacturer.
The following instructions may not apply to waterproof
devices. Refer to your device user manual or quick start
guide for more waterproof instruction if any.
• Do not use this apparatus near water.
• Do not expose this apparatus to dripping or splashing, and
ensure that no objects lled with liquids, such as vases, are
placed on the apparatus.
WARNING: To reduce the risk of re or electric shock, do not
expose this apparatus to rain or moisture.
CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
THIS SYMBOL ON THE PRODUCT MEANS THERE IS UNINSULATED,
DANGEROUS VOLTAGE WITHIN THE PRODUCT ENCLOSURE THAT
MAY PRESENT A RISK OF ELECTRICAL SHOCK.
THIS SYMBOL ON THE PRODUCT MEANS THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THIS GUIDE.
CAUTION FCC AND IC STATEMENT FOR USERS (USA AND
CANADA ONLY)
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
CAN ICES-003(B)/NMB-003(B)
FCC SDOC SUPPLIER’S DECLARATION OF
CONFORMITY
HARMAN International hereby declares that this equipment is in
compliance with the FCC Part 15 Subpart B.
The declaration of conformity may be consulted in the support
section of our Web site, accessible from www.jbl.com
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
CAUTION: Changes or modications not expressly approved
by HARMAN could void the user’s authority to operate the
equipment.
For Products That Transmit RF Energy:
(i) FCC AND IC INFORMATION FOR USERS
This device complies with Part 15 of the FCC rules and Industry
Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) This device may not cause

33
www.jbl.com
English
harmful interference; and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
(ii) FCC/IC Radiation Exposure Statement
This equipment complies with FCC and ISED radiation exposure
limits set forth for an uncontrolled environment.
In case this equipment has to subject to FCC/IC SAR (Specic
Absorption Rate) exposure test, this equipment is designed to
meet the requirements for exposure to radio waves established
by the FCC and ISED. These requirements set a SAR limit of
1.6 W/kg averaged over one gram of tissue. The highest SAR
value reported under this standard during product certication
for use when properly worn on the body or on the head, with
no separation. To meet RF exposure guidelines and reduce
exposure to RF energy during the operation, this equipment
should be positioned at least this distance away from the body
or the head.
For radio equipment operates in 5150-5850MHz
FCC and IC Caution:
High power radars are allocated as primary users of the 5.25 to
5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations
can cause interference with and/or damage to LE LAN (Licence-
Exempt Local Area Network) devices. No conguration controls
are provided for this wireless equipment allowing any change in
the frequency of operations outside the FCC grant of authorization
for US operation according to Part 15.407 of the FCC rules.
IC Caution:
User should also be advised that:
(i) The device for operation in the band 5150 - 5250 MHz
is only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems; (ii) the
maximum antenna gain permitted for devices in the bands
5250 - 5350 MHz and 5470 - 5725 MHz shall comply with
the e.i.r.p. limit: and
(ii) The maximum antenna gain permitted for devices in the
band 5725 - 5825 MHz shall comply with the e.i.r.p. limits
specied for point-to-point and non point-to-point operation
as appropriate.
Use Restriction Attention in European Union, operation is limited
to indoor use within the band 5150-5350 MHz.
Correct disposal of this product (Waste Electrical & Electronic
Equipment)
This symbol means the product must not be discarded as
household waste, and should be delivered to an appropriate
collection facility for recycling. Proper disposal and recycling helps
protect natural resources, human health and the environment.
For more information on disposal and recycling of this product,
contact your local municipality, disposal service, or the shop
where you bought this product.
This product is RoHS compliant.
This product is in compliance with Directive 2011/65/EU, and its
amendments, on the restriction of the use of certain hazardous
substances in electrical and electronic equipment.
REACH
REACH (Regulation No 1907/2006) addresses the production
and use of chemical substances and their potential impacts
on human health and the environment. Article 33(1) of REACH
Regulation requires suppliers to inform the recipients if an
article contains more than 0.1 % (per weight per article) of any
substance(s) on the Substances of Very High Concern (SVHC)
Candidate List (‘REACH candidate list’). This product contains
the substance “lead”(CAS-No. 7439-92-1) in a concentration of
more than 0.1% per weight.
At the time of release of this product, except for the lead
substance, no other substances of REACH candidate list are
contained in a concentration of more than 0.1% per weight in
this product.
Note: On June 27, 2018, lead was added to the REACH candidate
list. The inclusion of lead in the REACH candidate list does not
mean that lead-containing materials pose an immediate risk or
results in a restriction of permissibility of its use.
For devices with headphone jacks
WARNINGS/CAUTIONS
Do NOT use the headphones at a high volume for
any extended period.
- To avoid hearing damage, use your headphones
at a comfortable, moderate volume level.
- Turn the volume down on your device before
placing the headphones on your ears, then
turn the volume up gradually until you reach a
comfortable listening level.
For Products That Include Batteries
Instructions for Users on Removal, Recycling and Disposal
of Used Batteries
To remove the batteries from your equipment or remote control,
reverse the procedure described in the owner’s manual for
inserting batteries. For products with a built-in battery that lasts
for the lifetime of the product, removal may not be possible for
the user. In this case, recycling or recovery centers handle the
dismantling of the product and the removal of the battery. If, for
any reason, it becomes necessary to replace such a battery, this
procedure must be performed by authorized service centers. In
the European Union and other locations, it is illegal to dispose
of any battery with household trash. All batteries must be
disposed of in an environmentally sound manner. Contact your
local waste-management ofcials for information regarding the
environmentally sound collection, recycling and disposal of used
batteries.
WARNING: Danger of explosion if battery is incorrectly replaced.
To reduce risk of re, explosion or leakage of ammable liquid/
gas, don’t disassemble, crush, puncture, short external contacts,
expose to temperature above 60°C (140°F), sunshine or like,
expose to extremely low air pressure or dispose of in re or water.

44
EPILEPSY WARNING
A few people may experience epileptic
seizures when viewing ashing lights.
Precautions
Stand Mounting Safety Precautions
Always follow instruction and precaution advice from
speaker stand manufacturer.
This speaker contains a 36 mm receptacle cup to allow mounting
on tripod stands or on a pole over subwoofers. When using
stands or poles, be sure to observe the following precautions:
• Check the stand or pole specication to be certain the device
is designed to support the weight of the speaker. Observe all
safety precautions specied by the manufacturer.
• Always verify that the stand (or subwoofer/pole) is placed on
a at, level and stable surface and be sure to fully extend the
legs of tripod type stands. Position the stand so that the legs
do not present a trip hazard.
• Use this oor stand only on a at, solid surface. Once the
support (extended leg) has been placed and adjusted,
carefully tighten the screws and use the safety pin. After
placing the speaker on the stand, check for stability: When
tilting each direction to 10 degrees (for the surface), the
speaker should not turn off. If necessary, reduce the height
of the speakers and extend the base of the stand.
• Route cables so that performers, production crew, and
audience will not trip and topple the speakers over.
• Inspect the stand (or pole and associated hardware) before
each use and do not use equipment with worn, damaged or
missing parts.
• Do not attempt to place more than one PartyBox series
speaker on a stand or pole.
• Always be cautious in windy, outdoor conditions. It may
be necessary to place additional weight (i.e. sandbags) on
the base of the stand to improve stability. Avoid attaching
banners or similar items to any part of a speaker system.
Such attachments could act as a sail and topple the system.
• Unless you are condent that you can handle the weight of
the speaker, ask another person to help you get it onto the
tripod stand or pole.
Replace only with specied batteries. The symbol indicating
‘separate collection’ for all batteries and accumulators shall be
the crossed-out wheeled bin shown below:
WARNING - For Products Contain Coin/Button
Cell Batteries
DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD. This
product contains a coin/button cell battery. If the coin/button cell
battery is swallowed, it can cause severe internal burns in just
2 hours and can lead to death. Keep new and used batteries
away from children. If the battery compartment does not close
securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside
any part of the body, seek immediate medical attention.
For All Products with Wireless Operation:
HARMAN International hereby declares that this equipment is in
compliance with the essential requirements and other relevant
provisions of Directive 2014/53/EU and UK Radio Equipment
Regulations 2017. The declaration of conformity may be
consulted in the support section of our Web site, accessible from
www.jbl.com.

55
www.jbl.com
English
9. ADVANCED USAGE 13
9.1 JBL PARTYBOX APP 13
9.2 LIGHT EFFECT 13
9.3 TWS MODE 13
9.4 DAISY CHAIN 13
9.5 FACTORY RESET 13
9.6 IPX4 14
10. SPECIFICATIONS 14
11. TROUBLESHOOTING 15
12. COMPLIANCE 15
13. TRADEMARK 16
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS 2
1. INTRODUCTION 6
2. WHAT’S IN THE BOX 6
3. PRODUCT OVERVIEW 7
3.1 TOP PANEL 7
3.2 BACK PANEL 7
4. PLACEMENT 8
5. POWER ON 9
6. USING YOUR PARTYBOX 9
6.1 BLUETOOTH CONNECTION 9
6.2 USB CONNECTION 10
6.3 MUSIC CONTROL 10
6.4 AUX CONNECTION 10
6.5 MIXING SOUND WITH A MICROPHONE AND /
OR GUITAR 11
6.6 CHARGING YOUR MOBILE DEVICE 11
7. CARRYING YOUR PARTYBOX 12
8. POLE-MOUNTING YOUR PARTYBOX 12

66
2. WHAT’S IN THE BOX
12 3
1) Main unit
2) Power cord*
3) Quick Start Guide, Safety Sheet, Warranty Card
*Power cord quantity and plug type vary by regions.
1. INTRODUCTION
Congratulations on your purchase! This manual includes
information about PARTYBOX 110 speakers. We encourage
you to take a few minutes to read this manual, which describes
the product and includes step-by-step instructions to help you
to set up and get started. Read and understand all the safety
instructions before using your product.
If you have any questions about these products, their installation
or their operation, please contact your retailer or customer
service, or visit us at www.jbl.com.

77
www.jbl.com
English
3. PRODUCT OVERVIEW
3.1 Top Panel
4
6
1
8
2
3
7 5
1) Mobile device dock
2)
• Turn the power on or off.
3) Battery level indicator
4)
• Press to play, pause or resume.
• Rotate clockwise / counterclockwise to increase /
decrease the main volume.
5)
• Enhances the bass level: level 1, level 2, or off.
6) LED ring
7)
• Press to enter Bluetooth pairing mode.
• Press and hold for more than 10 seconds to forget all
paired devices.
8)
• Rotate clockwise / counterclockwise to switch between
different light patterns.
• Press to turn light effect on or off.
• Hold for more than 2 seconds to turn strobe light on or
off.
Caution:
– Do not look directly at the light-emitting parts when the speaker
lights are turned on.
LED behavior
Solid white Power on
Off Standby / Power off
Flashing white quickly Pairing
Solid white Connected
Off Not connected
Dimmed white Level 1
Solid white Level 2
Off Off
Flashing red quickly Low battery
Flashing white slowly Charging
Solid white
The speaker is fully
charged when the entire
light stripe turns solid
white.
3.2 Back Panel
11
2
3
4
8
7
1
5
9
10
6
12
1) TWS
• Press to enter True Wireless Stereo (TWS) pairing mode.
2) Guitar volume
• Adjust volume of the connected guitar.
3) GAIN (guitar)
• Adjust gain of the connected guitar.
4) Guitar socket
• Connect to a guitar.
5) AUX OUT
• Daisy-chain PARTYBOX speakers through 3.5 mm audio
cables (not supplied).
6) AUX IN
• Connect to an external audio device through a 3.5 mm
audio cable (not supplied).
• Daisy-chain PARTYBOX speakers through 3.5 mm audio
cables (not supplied).

88
7) Microphone socket
• Connect to a microphone.
8) GAIN (microphone)
• Adjust gain of the connected microphone.
9) Microphone volume
• Adjust volume of the connected microphone.
10) USB
• Connect to a USB storage device.
• Charge your mobile device.
11) AC
• Connect to AC power supply.
12) Pole-mounting your PARTYBOX
4. PLACEMENT
Caution:
– Do not sit or lean on the speaker or push it sideways to avoid tip-
over and possible damages.
Place the speaker on a at, stable surface and ensure that the
rubber feet side is down.

99
www.jbl.com
English
5. POWER ON
Cautions:
– Use the provided power cords only.
– You can use either AC power or the built-in battery as power
supply to the speaker.
OFF
ON
<15%
15% - 80%
>80%
1. Connect AC power.
• To use the built-in battery, disconnect AC power after
charging the speaker.
2. Press to power on.
Tips:
– Fully charge the speaker before rst-time use to prolong the
lifespan of the built-in battery.
– You can check the battery level by pressing any button on the
speaker.
– The speaker switches to standby mode automatically after
20 minutes of inactivity. You can press on the speaker to switch
to normal operation.
6. USING YOUR PARTYBOX
Notes:
– Only one sound source can be played at a time. The priority order
is USB -> BLUETOOTH -> AUX.
– Starting a source with higher priority will always interrupt a source
with lower priority.
– To start a source with lower priority, stop the source with higher
priority rst.
6.1 Bluetooth Connection
You can use the speaker with your Bluetooth enabled smartphone
or tablet.
DEVICES
JBL PartyBox 110
Bluetooth
Bluetooth
2
1
<10 m (33 ft)
1. Switch to the BLUETOOTH source.
2. Press on the speaker to enter Bluetooth pairing mode.
3. Choose “JBL PartyBox 110” on your Bluetooth device to
connect.
4. Once successfully connected, you can stream audio from
your Bluetooth device to this speaker.
Notes:
– This speaker can memorize a maximum of 8 paired devices. The
ninth paired device will replace the rst one.
– Enter “0000” if a PIN code is requested for connection to a
Bluetooth device.
– Bluetooth performance can be affected by the distance between
this product and your Bluetooth device and the environment of
operation.
To terminate the Bluetooth-enabled device:
• Turn off this speaker, or
• Disable Bluetooth on your device.

1010
To reconnect the Bluetooth enabled device:
• When you turn on this speaker next time, it tries to reconnect
the last connected device automatically.
• If not, manually select “JBL PartyBox 110” on your Bluetooth
device to connect.
6.2 USB Connection
Plug a USB storage device that contains playable audio contents
into the USB port of the speaker.
JThe speaker switches to the USB source automatically.
JAudio playback will start automatically.
Tip:
– The speaker plays audio les on the USB storage device from the
root folder to the last level of subfolders in alphabetical sequence.
Up to 8 levels of subfolders are supported.
Supported audio formats
Extension Codec Sample rate Bitrate
WAVE PCM 44.1KHz ~ 192KHz < 5Mbps
LPCM 44.1KHz ~ 192KHz < 5Mbps
IMA_
ADPCM
44.1KHz ~ 192KHz < 5Mbps
MPEG 44.1KHz ~ 192KHz < 5Mbps
MULAW 44.1KHz ~ 192KHz < 5Mbps
MP3 MPEG1
layer1/2/3
32KHz ~ 48KHz 32Kbps ~
320Kbps
MPEG2
layer1/2/3
16KHz ~ 24KHz 8Kbps ~
160Kbps
MPEG2.5
layer3
8KHz ~12KHz 8Kbps ~
160Kbps
WMA ≤ 320Kbps 8Kbps ~
48Kbps
6.3 Music Control
x 1
x 2
x 3
• Press once to pause or resume playback.
• Press twice to skip to the next track.
• Press three times to skip to the previous track.
• Rotate the knob clockwise / counterclockwise to increase /
decrease the main volume.
• Press BASS BOOST to enhance the bass level: level 1, level
2, or off.
Note:
– The skip operation is unavailable in AUX mode.
6.4 AUX Connection
1. Connect an external audio device to the speaker through a
3.5 mm audio cable (not supplied).
2. After stopping playback from any other source, start audio
playback on the external device.

1111
www.jbl.com
English
6.5 Mixing Sound with a Microphone and /
or Guitar
By using a microphone or electric guitar (not supplied), you can
mix sound with an audio source.
Notes:
– Always set the guitar or microphone volume to the minimum level
before guitar or microphone connection / disconnection.
– Always disconnect the guitar or microphone when you are not
using them.
6.5.1 Connecting a Microphone
Connect a microphone to the microphone socket.
6.5.2 Connecting a Guitar
Connect a guitar to the guitar socket.
6.5.3 Mixing Sound
Sing through the microphone or play guitar.
• To adjust the volume of the audio source, rotate the knob
clockwise / counterclockwise.
• To adjust the volume of the microphone or guitar, rotate the
microphone or guitar volume knob.
• To adjust the gain of the wired microphone or guitar, rotate
the GAIN control beside the microphone or guitar socket
respectively.
6.6 Charging Your Mobile Device
Note:
– The USB port is for charging purpose only.

1212
7. CARRYING YOUR PARTYBOX
Cautions:
– Before carrying the speaker, ensure that all the cords are
disconnected.
– To avoid personal injury and/or property damage, hold the product
rmly while carrying.
Hold the handles rmly to carry the speaker.
8. POLE-MOUNTING YOUR
PARTYBOX
Cautions:
– Installation must be done by qualied persons using safe rigging
standards.
– The installer is responsible for proper selection and use of mounting
hardware, to properly and safely pole-mount the speakers.
2
36 mm
1
10.84 kg / 23 lbs

1313
www.jbl.com
English
9. ADVANCED USAGE
9.1 JBL PARTYBOX App
Download and install the JBL PARTYBOX App to get more from
the product.
9.2 Light Effect
2S
x1
• Press to turn the light effect on or off.
• Hold for more than 2 seconds to turn strobe light on or off.
• Rotate the knob to select your preferred light effect: rock,
ow, cross, ripple, or ash.
9.3 TWS Mode
You can connect two PARTYBOX speakers to each other via
TWS mode.
Press TWS on both speakers.
To exit TWS mode:
Power off or press TWS on either speaker.
Tip:
– By default, the speaker connected to your Bluetooth device acts as
the primary speaker (left channel), while the other one acts as the
secondary speaker (right channel).
9.4 Daisy Chain
9.5 Factory reset
To restore the factory settings, hold and for more than
10 seconds.

1414
10. SPECIFICATIONS
General specication
Model No.: JBL PartyBox 110
Transducers: 2 x 154.6 mm / 5.25” woofer,
2 x 55 mm / 2.25” tweeter
Output power: 160 W RMS
Power input: 100 V - 240 V / 50/60 Hz
Frequency response: 45 Hz - 20 kHz (-6 dB)
Signal-to-noise ratio: > 80 dB
Battery type: Li-ion polymer 36 Wh
Battery charge time: 3.5 hours
*Music play time: Up to 12 hours
USB specication
USB format: FAT16, FAT32
USB le format: .mp3, .wma, .wav
USB charge out: 5 V / 2.1 A (maximum)
Cable type: AC Power Cable
Cable length: 2000 mm / 78.7”
Wireless specication
Bluetooth®version: 5.1
Bluetooth® prole: A2DP 1.3, AVRCP 1.6
Bluetooth®transmitter
frequency range: 2.4 GHz - 2.4835 GHz
Bluetooth®transmitter
power: ≤ 15 dBm (EIRP)
Bluetooth®transmitter
modulation: GFSK, π/4 DQPSK, 8DPSK
Dimensions
Dimensions (W x H x D): 295 mm x 568 mm x 300 mm /
11.6” x 22.4” x 11. 8”
Weight: 10.84 kg / 23 lbs
* 12 hrs battery playtime is only a reference and may vary depending
on music content and battery aging after numerous charging and
discharging cycles. It’s achievable with a predened music source, light
show switched off, volume level at 7 and Bluetooth streaming source.
9.6 IPX4
Caution:
– Always keep the charging port dry before connecting AC power.
– To ensure splash resistance, always keep the protective covers
closed securely.
The speaker is IPX4 splash resistant.

1515
www.jbl.com
English
12. COMPLIANCE
The product is in compliance with the European Union energy
legislation.
Bluetooth connection mode
The product is intended to be used for streaming music via
Bluetooth connection. A consumer can stream Bluetooth
audio to the speaker. When the product is connected through
Bluetooth, the Bluetooth connection must remain active at all
times to ensure proper operation.
The product will enter sleep mode (networked standby) after
20 minutes without operation. The power consumption in sleep
mode is less than 2.0 Watts, after which it can be re-activated
via Bluetooth connection.
Bluetooth disconnection mode
The product will enter standby mode after 20 minutes without
operation. The power consumption in standby mode is less than
0.5 Watts.
11. TROUBLESHOOTING
Caution:
– Never try to repair the product by yourself. If you have any
problems while using this product, check the following points
before you request service.
System
The speaker will not turn on.
• Ensure that the speaker battery is not drained. If not, use the
AC power instead.
No response from some buttons
• The product may be in demo mode. In demo mode, the
and buttons are disabled. Hold and simultaneously
for more than 5 seconds to exit.
Sound
No sound from the speaker.
• Ensure that the speaker is powered on.
• Adjust volume.
• Ensure that a sound source is active and not muted.
Bluetooth
A device cannot connect with the speaker.
• Ensure that the Bluetooth function of the device is enabled.
• The speaker is already connected with another Bluetooth
device. Hold on the speaker for more than 10 seconds to
disconnect and pair with a new device.
Poor audio quality from a connected Bluetooth device
• The Bluetooth reception is poor. Move the device closer to
the speaker, or remove any obstacle between the device and
speaker.

1616
13. TRADEMARK
The Bluetooth®word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by
HARMAN International Industries, Incorporated is under license.
Other trademarks and trade names are those of their respective
owners.
Este produto está homologado pela Anatel, de acordo com os
procedimentos regulamentados para avaliação da conformidade
de produtos para telecomunicações e atende aos requisitos
técnicos aplicados.
Para maiores informações, consulte o site da Anatel –
www.anatel.gov.br
Este equipamento não tem direito à proteção contra interferência
prejudicial e não pode causar interferência em sistemas
devidamente autorizados.